Buy Best Conduit Bender from AMAZON amzn.to/3Ku17mw
Пікірлер
I know you’re just showing the proper way that you should do it but honestly how many guys even put the vendor on the floor for a 30° offset or any offset for that matter other than a 90°? Most of my bending as an apprentice I’ve been taught to do in the air
@bmcfad122 жыл бұрын
Soon to be cw here thanks for the vid
@tragan1442 Жыл бұрын
Great video but explain to people how multipliers are found using Trig?
@adams6798 Жыл бұрын
good job
@mohammedhassani39754 жыл бұрын
Great video. Thanks for posting. Nice looking bender. What brand is it? (Thanks in advance for the answer.)
@glennmann6343 жыл бұрын
Sorry i didn't remember the brand.
@passionateengineer043 жыл бұрын
how need majarmant
@jakirsheikh26313 жыл бұрын
This doesn't show how to use shrinkage to calculate for a given distance between the end of the conduit and the beginning of the first bend.
@Bapuji42 Жыл бұрын
Does the diameter of the conduit have anythi g to do with the "shrink" or is it all treated like a thin line?
@ryanb18744 жыл бұрын
Consider it as thin line.
@passionateengineer044 жыл бұрын
Depending on bending angle you should put your mark on the tangent of the angle. In this scenario you can see that the mark is in front of the bend as it should be in the center of the bend. This is important if you need the bends to be in an exact location.
@diazaa3 жыл бұрын
How do I put at mark at 0.57735026919?
@AngelRomero9552 жыл бұрын
@@AngelRomero955 .57 degrees?
@diazaa2 жыл бұрын
I found in another video that when making parallel runs with offsets. You need/want to use the Tangent of the offset angle. So it checks out. I’m a 1st year apprentice I still haven’t done any fancy bends.
@AngelRomero9552 жыл бұрын
@@AngelRomero955ok but what was your question about marking at .57? I have alot of experience (10+yrs) measuring for, routing and bending hydraulic tubing.
@diazaa2 жыл бұрын
@@AngelRomero955 Huh? The distance between marks is 1/sin(angle) times the offset rise.
@Bapuji42 Жыл бұрын
Ok!! How tje eff do you find the multiplier
@mariamontolla59784 жыл бұрын
The multiplier has to do with the angle, it's 30 degrees, sine of 30 = .5. But we are dividing by SINE 30, so it's like multiply by 2. Get the uglies manual.
@ryanb18744 жыл бұрын
45=1.414, 30=2, 15=3.86.... Those are the only ones I have memorized.
@diazaa3 жыл бұрын
a way to find the multiplier for any bend angle is - 1/Sine(angle
@lazarevic953 жыл бұрын
@@lazarevic95 Hey now, dont give away these magical tricks of the trade!!!
@diazaa2 жыл бұрын
hey viewed by me :D
@jarrisyed83723 жыл бұрын
Si hubiera subtitulado español sinvirioa
@juancarlosarayamanriquez28503 жыл бұрын
Its time to move on kopex like rest of the world!!
@alen22832 жыл бұрын
What video is This from?
@patricktelfort4 жыл бұрын
For conduit bending
@passionateengineer044 жыл бұрын
The title of the actual video
@patricktelfort4 жыл бұрын
@@patricktelfort Multiplier method of offset bend
@passionateengineer044 жыл бұрын
PASSIONATE ENGINEER Good video
@jondyer47534 жыл бұрын
"pick a spot, bend it... then pick another spot, bent it... then you have nothing you're looking for. Thanks for not actually explaining what the multiplier is and how you find it.
@FuquarProductions9 ай бұрын
You probably forgot to show the 1st and 2nd step which is ; preparing the necessary materials,tools,and equipment. And wearing ppe
I know you’re just showing the proper way that you should do it but honestly how many guys even put the vendor on the floor for a 30° offset or any offset for that matter other than a 90°? Most of my bending as an apprentice I’ve been taught to do in the air
Soon to be cw here thanks for the vid
Great video but explain to people how multipliers are found using Trig?
good job
Great video. Thanks for posting. Nice looking bender. What brand is it? (Thanks in advance for the answer.)
Sorry i didn't remember the brand.
how need majarmant
This doesn't show how to use shrinkage to calculate for a given distance between the end of the conduit and the beginning of the first bend.
Does the diameter of the conduit have anythi g to do with the "shrink" or is it all treated like a thin line?
Consider it as thin line.
Depending on bending angle you should put your mark on the tangent of the angle. In this scenario you can see that the mark is in front of the bend as it should be in the center of the bend. This is important if you need the bends to be in an exact location.
How do I put at mark at 0.57735026919?
@@AngelRomero955 .57 degrees?
I found in another video that when making parallel runs with offsets. You need/want to use the Tangent of the offset angle. So it checks out. I’m a 1st year apprentice I still haven’t done any fancy bends.
@@AngelRomero955ok but what was your question about marking at .57? I have alot of experience (10+yrs) measuring for, routing and bending hydraulic tubing.
@@AngelRomero955 Huh? The distance between marks is 1/sin(angle) times the offset rise.
Ok!! How tje eff do you find the multiplier
The multiplier has to do with the angle, it's 30 degrees, sine of 30 = .5. But we are dividing by SINE 30, so it's like multiply by 2. Get the uglies manual.
45=1.414, 30=2, 15=3.86.... Those are the only ones I have memorized.
a way to find the multiplier for any bend angle is - 1/Sine(angle
@@lazarevic95 Hey now, dont give away these magical tricks of the trade!!!
hey viewed by me :D
Si hubiera subtitulado español sinvirioa
Its time to move on kopex like rest of the world!!
What video is This from?
For conduit bending
The title of the actual video
@@patricktelfort Multiplier method of offset bend
PASSIONATE ENGINEER Good video
"pick a spot, bend it... then pick another spot, bent it... then you have nothing you're looking for. Thanks for not actually explaining what the multiplier is and how you find it.
You probably forgot to show the 1st and 2nd step which is ; preparing the necessary materials,tools,and equipment. And wearing ppe
Ahhh yes Vietnam
Ummm this is not helpful