KZhead
Тәжірибелік нұсқаулар және стиль

How to Make Cabinet Door Frames - Rail and Stile Bit Tutorial and Demo

Matt Montavon (MMCC_Woodshop)
2024 ж. 17 Мам.
168 740 Рет қаралды
Жүктеу

In this video I'll show you how to make cabinet door frames with rail and stile bits! This is very easy once you understand the setup, and this gives professional results!
**Check out my NEW Etsy page**
mmccwoodshop.etsy.com
Products/tools in this video (amazon affiliate links)
Rail & Stile bits: amzn.to/3PJBil6
Rockler coping sled: amzn.to/3JdvZbj
Less expensive coping sled: amzn.to/3BIU34f
Dewalt 2.25 hp router: amzn.to/3PN2Gii
Rockler pro lift (make sure this fits your table, there are different sizes) :
amzn.to/3PLVaUR
Festool CTA 48 Dust Extractor: amzn.to/2S43gjb
Set up jig blocks: www.rockler.com/router-bit-se...
Rockler router table:
www.rockler.com/complete-basi...
This was filmed with a GoPro Hero 8 Black and edited in iMovie. Thanks for watching! Be sure to subscribe and check out some of my other videos! Find me on Instagram (MMCC_Woodshop) for more of my work!

*DISCLAIMER* The following content is for entertainment purposes only. Woodworking and using power tools can be extremely dangerous if not done properly. YOU (the viewer) are fully responsible for understanding proper use of tools, as well as the safety features of each. I highly suggest reading the owners manual and/or watching how-to videos on the tools. I (MMCC_Woodshop) am not responsible nor liable for any injury, death, or handing of the tools you may use, nor do I assume to display the proper handing of as a demonstration. Please use extreme caution when working with any power tools. - Matt
Want to support my channel? Feel free to buy me a coffee!www.buymeacoffee.com/mmccwoodsh7

Пікірлер

  • I've done a lot of door like this, and when you route the groove first, you'll end up with tearout when you create the tounges. Much better to create your rails and tongues first, then run your grooves for the rest. Also, the rockler sled has a backer piece of wood that will help prevent tearout on creating the tounges so move it flush to the fence with your work piece, that's why it's there.

    @BobBrittonBespoke@BobBrittonBespoke Жыл бұрын

    • Great input Bob, thanks for the tips!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • I thought these bits came with a bit to do a cut on the outer edges on the doors? I want to get this very set of bits to match the recessed panel doors on my kitchen cabinets. The cabinet doors I have, have an angled cut with a slight "coved" profile.

      @Mark-in5yw@Mark-in5yw Жыл бұрын

    • And that backer bird after some use you can change it God bless all who call on the Lord who shed his blood for all Amen praise to The king. Bottom line

      @patrickarchuleta9594@patrickarchuleta959410 ай бұрын

    • Never seen the style done first I always thought you do the rails then the styles

      @blakecollie8770@blakecollie87707 ай бұрын

    • Can you use a 1/4 shank to do cabinet doors?

      @christiancarfann@christiancarfann4 ай бұрын

  • Finally went out and got myself that very router bit set. It's been sitting in my cabinets for - oh - I don't know how long. Today I'm going to grab some scrap and mill it to a consistent dimension and then just throw together a frame just like yours. They say imitation is the most sincere gratitude. Thanks.

    @petec6690@petec6690 Жыл бұрын

    • Nice! This setup has turned out to be a great investment and I’ve used this several times since this video. Thanks for watching and good luck with your frame builds!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Great tutorial Matt just what i need to start making my own shaker doors my kitchen cabinets"!!

    @jerrychaisson9308@jerrychaisson93088 күн бұрын

    • Thanks! Glad the video was helpful!

      @mmcc_woodshop6288@mmcc_woodshop62888 күн бұрын

  • This is very helpful. Thank you.

    @landjwilk@landjwilk14 күн бұрын

    • Glad it was helpful!

      @mmcc_woodshop6288@mmcc_woodshop628811 күн бұрын

  • I've just realized why I love shaker doors

    @LayZeeDawg@LayZeeDawg10 ай бұрын

    • They’re the best! 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop628810 ай бұрын

  • A rarely comment a video, but I appreciate how well and detailed you explained everything, i hope your channel grow up fast

    @reicoll9501@reicoll9501 Жыл бұрын

    • Thanks for the feedback and for watching!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • 😅😅😅😅😅😊😅😅😊😊😊😊😊😊😊​@@mmcc_woodshop6288

      @thomascraycraft3087@thomascraycraft30872 ай бұрын

  • Great vid. My issue I like to use 3/8 panels and leave 1/8 backside reveals so I get the 1/4 inch front side shaker look on 3/4 stock

    @BZ1340@BZ13405 күн бұрын

  • Thanks for the video it really saved me. I bought the router bit set and started to figure out how to use by myself. I was already about to throw it out of window :) Now I can keep it and use it.

    @IFGCZ@IFGCZ4 ай бұрын

    • Glad the video was helpful, thanks for watching and your feedback!

      @mmcc_woodshop6288@mmcc_woodshop62884 ай бұрын

  • Excellent video, very clear and precise instruction, and now time to work on my new doors! Keep this great videos going as you are a pretty good instructor! Have a blessed day!

    @fernandovelasquez7883@fernandovelasquez7883 Жыл бұрын

    • Thanks Fernando!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • This is the best video I ever seen about door making thank you

    @naturalmystics-kd9vt@naturalmystics-kd9vt7 ай бұрын

    • Thanks for the feedback!

      @mmcc_woodshop6288@mmcc_woodshop62886 ай бұрын

  • Excellent instructional. Thank you for creating and sharing this video!

    @LuciaCockfield@LuciaCockfield Жыл бұрын

    • Thanks Lucia!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Outstanding explanation and demonstration! Most helpful. Thank you!!

    @rickfrench786@rickfrench786 Жыл бұрын

    • Thanks Rick!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • That’s a great instructional video and very well presented. Thanks for posting.

    @angelarowlands3231@angelarowlands3231 Жыл бұрын

    • Thanks Angela!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Great tutorial. Easy to understand for a beginner.

    @keithwilliamson236@keithwilliamson2362 ай бұрын

    • Thanks Keith!

      @mmcc_woodshop6288@mmcc_woodshop62882 ай бұрын

    • I have the Ogee rail and stile router bit set. Im confused on which set up jig to order from your description list. Would it be 91991 stile and rail or 40431 shaker stile and rail? @@mmcc_woodshop6288

      @keithwilliamson236@keithwilliamson2362 ай бұрын

  • Beautiful work ❤

    @davidndahura7437@davidndahura743711 ай бұрын

    • Thanks David!

      @mmcc_woodshop6288@mmcc_woodshop628811 ай бұрын

  • Clear and informative video, thank you for posting this. I am planning to make my own in frame kitchen this summer and am currently learning how to do this and what tools are required. Without people like yourself I would not know where to start. Will need to invest in expensive tools but I am sure they will pay for themselves over time on other project and with my self satisfaction 😀

    @chrismoore7569@chrismoore7569 Жыл бұрын

    • Thanks for the input Chris! I agree that tools and a set up can be expensive but the ROI on these tools can be huge if you build and sell multiple projects, or use it for home use 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Thank you. Well detailed explanation. Job well done.

    @Ninoy2059@Ninoy2059 Жыл бұрын

    • You’re welcome and thanks for watching!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Thanks for the great video. I am preparing to venture into making my first shaker bevel frames. I got the Rockler 40431 router bit with the template.

    @GK-qz3cm@GK-qz3cm3 ай бұрын

    • Nice, glad the video was helpful and good luck with the frames!

      @mmcc_woodshop6288@mmcc_woodshop62883 ай бұрын

  • very good explanation it's clear my mind Thank you.

    @archiejoseph6681@archiejoseph6681 Жыл бұрын

    • Thanks Archie! 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Cool video. Thank you. I sometimes find the skinny back cracks easily when inserting the panel.

    @maceo2012@maceo20122 ай бұрын

    • Thanks for the feedback! It can help to leave the pieces wider to prevent cracking (if possible). I’ve run into that issue a few times myself

      @mmcc_woodshop6288@mmcc_woodshop62882 ай бұрын

  • Very comprehensive very useful I am new in woodworking And you have another subscriber and thats me, hope I'll learn much more from you

    @adeelbaig8708@adeelbaig8708 Жыл бұрын

    • Thanks for the feedback and for watching!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • great video, thank you, I did this last year when I saw the cost of doors, I needed 9 doors! The savings from 1 door almost paid for the bit. The bits are expensive if you get a good quality, which I recommend. I used finger jointed boards. Also use a sacrificial board next to the one you are cutting to help with tear out. The plastic guide was a huge help and I saved back a couple wood pieces as back ups.

    @Cam-wi3tp@Cam-wi3tp Жыл бұрын

    • Thanks for the feedback and tips Cam! You're right about that - crazy expensive for the set of bits but a $$ saver in the long run if you have to make multiple frames!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Great idea

    @aaudain1@aaudain1 Жыл бұрын

    • Thanks Anthony!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Great video, thanks for sharing! Cheers

    @marct2124@marct21242 ай бұрын

    • Thanks Marc!

      @mmcc_woodshop6288@mmcc_woodshop62882 ай бұрын

  • Thank you so much for this video

    @naturalmystics-kd9vt@naturalmystics-kd9vt7 ай бұрын

    • You’re welcome, thanks for watching!

      @mmcc_woodshop6288@mmcc_woodshop62886 ай бұрын

  • Great video. I would cut the end grain first so you can remove any breakout when you do the second cuts

    @AndyCarnegie@AndyCarnegieАй бұрын

    • Thanks! Great tip and thanks for sharing!

      @mmcc_woodshop6288@mmcc_woodshop6288Ай бұрын

  • Fantastic instructional video! I feel like I'm watching one of those wood magazine style vids, but better. Have you ever thought to do more vids like this?

    @rabwilson6974@rabwilson6974 Жыл бұрын

    • Thanks Rab! I’d definitely like to do more for sure, just have to figure out what to demo next!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Only comment I have is you need a backer for the end grain cut, this will prevent tearout. Good instructions and all the links to the tools used.

    @dlf43338@dlf43338 Жыл бұрын

    • Thanks! Yes, backer board is necessary for sure 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • you could do end cuts first then your long cuts to clean up the copes.

      @andykrask3184@andykrask3184 Жыл бұрын

  • Amazing video

    @davidboston4574@davidboston45744 ай бұрын

    • Thanks David!

      @mmcc_woodshop6288@mmcc_woodshop62884 ай бұрын

  • Good job brother

    @Juniorjohn9152@Juniorjohn9152 Жыл бұрын

    • Thanks Yaseen!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Thanks for your help I need help with this job

    @josearango8838@josearango8838 Жыл бұрын

    • You’re welcome, thanks for watching!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • What an excellent video. I’m very new to routing tables and this is something that I have wanted to try. This answers so many questions around what is achievable, using which tools and how to do it. Very nicely done. You have a new subscriber! Just one question, did you make that setup block or did it come with the router bit set?

    @richardm9550@richardm9550 Жыл бұрын

    • Thanks Richard! The set up block is purchased separately, they’re around $10ish.. just make sure you get the correct block that matches the bits you have. There’s a link to the blocks on Rockler’s site in the description!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Excelentes videos.

    @VientoNegro284@VientoNegro2845 ай бұрын

    • Thanks!

      @mmcc_woodshop6288@mmcc_woodshop62885 ай бұрын

  • Bravo!

    @mickey533@mickey533 Жыл бұрын

    • 👍🏻👍🏻🙌🏻🙌🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Thanks !

    @benohsten9323@benohsten93232 ай бұрын

    • Thanks for watching!

      @mmcc_woodshop6288@mmcc_woodshop62882 ай бұрын

  • is there any "hand tool" to do this? instead of the table one

    @ScarletCarsonDoll@ScarletCarsonDoll9 ай бұрын

    • Not that I’m aware of, I think a router table or shaper is the only way this can be done

      @mmcc_woodshop6288@mmcc_woodshop62889 ай бұрын

    • There is. It’s called a moulding plane.

      @shofarsogood7504@shofarsogood75046 ай бұрын

  • Great video. Is your rail & style bit specifically designed to create the decorative inlay or can it be used for a flush square shaker door frame?

    @jens2763@jens2763 Жыл бұрын

    • Thanks! The set in this video is specific to the decorative inlay trim. Here's a link to a set that would resemble much closer to shaker style! amzn.to/3Q2inTO

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • thanks for sharing all the details and Rockler's system. Is there any simple rule of thumb to measure the length of the shorter pieces (stiles?)? This is something I never really managed to figure out... measuring the depth of the groove seems pretty odd and finicky to me :D any better idea?

    @tiborpolgar435@tiborpolgar435 Жыл бұрын

    • The bits (at least this set) are specific to a 3/8” groove, so when measuring the length of the stiles, you’ll want to add 3/4” (3/8” on each side of the stile) to the total length. When you cut the edges out, it cuts a 3/8” groove on each end so the additional 3/4” you added disappears from the overlap 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • @@mmcc_woodshop6288 that's clear now, thank you for your reply! :)

      @tiborpolgar435@tiborpolgar435 Жыл бұрын

  • Where did you get? Find or make that setup block you used for the setup on the bit? That white clear piece. Thanks!

    @chrisweidtgolf@chrisweidtgolf3 ай бұрын

    • Here’s the link, you need to select the model piece that matches the router bits you’re using. www.rockler.com/router-bit-set-up-jigs-rail-and-stile-bits

      @mmcc_woodshop6288@mmcc_woodshop62883 ай бұрын

  • I missed how you knew the rough cut dimensions of the rails in order to get the door width you wanted. Does the router bit set tell you how much to allow for the tongue and groove depth? Also, is there a good way to determine the dimensions of the door panel or do you just measure it after the cuts are made?

    @sandiegodan@sandiegodan11 ай бұрын

    • Yes, the tongue on these bits is 3/8” inset. So you’d need to add an extra 3/4” (3/8” on each side) to the pieces that include the tongue 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop628810 ай бұрын

  • Hi, I have seen vids where they mention that plywood does not match the thickness of the cut as the standard thickness of the ply is not exactly what it is listed as being. Did you find a panel to fit snugly and if so, what thickness was it.

    @TrixyLixyStix@TrixyLixyStix Жыл бұрын

    • 1/4” plywood fits the groove.. the stuff I had in the video was 5mm, which is a little thinner. I didn’t have any 1/4” at the time of filming

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • So sweet. I already have the Jig, but not the plastic block. Where can i get?

    @frankcherry3810@frankcherry3810 Жыл бұрын

    • Here’s the link, just make sure you get the right block that matches the profile of your bits www.rockler.com/router-bit-set-up-jigs-rail-and-stile-bits

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Hi. Great video! The link you provided for the set up jog blocks isn't working. Is it possible to update it or give me more info so I can research it?

    @freedomhomeimprovementsny6506@freedomhomeimprovementsny6506 Жыл бұрын

    • Here's the new link - I'll update it in the description! www.rockler.com/router-bit-set-up-jigs-rail-and-stile-bits

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • @@mmcc_woodshop6288 Thanks so much for the follow up!

      @freedomhomeimprovementsny6506@freedomhomeimprovementsny6506 Жыл бұрын

  • Hello, i watch your video it showed me how to make shaker doors . Can you tell me what the item number is on the router bits so i can buy a set. Thank you

    @jeffbarneycastle9739@jeffbarneycastle97393 ай бұрын

    • It’s item #92013 on Rockler’s website

      @mmcc_woodshop6288@mmcc_woodshop62883 ай бұрын

  • Ok I tried again and this time I did 3passes taking a little more material each time. Success! So I’m thinking that this is what I get for buying my bits at Harbor freight and I should maybe invest a little more money in a quality style and rail bit set. What do you think?

    @johnjaconsky4488@johnjaconsky4488 Жыл бұрын

    • Nice! Router bits are expensive but I think they are worth the price. I try to always use Freud bits. I think I'm more terrified of using a cheaper bit at 10,000 - 15,000 rpm.

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • @@mmcc_woodshop6288 Ok thanks for the tips

      @johnjaconsky4488@johnjaconsky4488 Жыл бұрын

  • I’ll buy you a coffee if you tell me what attachment (and where you got it) you are using for your festool dust collector in this video? Thanks!

    @scottdutton7160@scottdutton71608 ай бұрын

    • Hey Scott, it's literally just the 36mm festool hose wedged down into the dust port on the router table - no special attachment. Here's the links to the hose, and the router table (you have to buy the router table accessory kit separately - the dust chute comes in the accessory kit. Dust hose: amzn.to/481i6cl Router table & accessory kit: www.rockler.com/complete-basic-router-table-kit-with-accessory-kit?country=US&sid=V91040&promo=shopping&PL&gclid=Cj0KCQjwio6XBhCMARIsAC0u9aHFkIgOKw2qMP-8nDvjofbcvcor2h1apQ8rnKkPlwc5B2Jppnomty0aAq7gEALw_wcB

      @mmcc_woodshop6288@mmcc_woodshop62888 ай бұрын

  • Who did you purchase the coping sled and is it affordable.God bless you and your family outstanding job great attitude

    @patrickarchuleta9594@patrickarchuleta959411 ай бұрын

    • It’s from Rockler - check out this link Rockler coping sled: amzn.to/3JdvZbj Thanks for watching!

      @mmcc_woodshop6288@mmcc_woodshop628810 ай бұрын

  • Consider feather boards on both the fence and the bed of your router table. Much safer and much more uniform results.

    @mattschreiber4251@mattschreiber4251 Жыл бұрын

    • Great tips! Thanks for the input!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • I make my end cuts first because of blow out. Then do my side cuts.

    @biggreg100@biggreg1004 ай бұрын

    • Nice tip, thanks for sharing!

      @mmcc_woodshop6288@mmcc_woodshop62884 ай бұрын

  • Can this be done with a portable/compact router

    @TheCoffeeField@TheCoffeeField Жыл бұрын

    • No, these bits should only be used in a table. You may be able to use a compact router in a table set up, but it would likely be underpowered for making these cuts.

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • How much longer and wider do you need to make each piece? How do you figure that out?

    @oxwilder@oxwilder Жыл бұрын

    • The second bit cuts a 3/8” tongue into the frame piece (on each side), so you’ll need to keep the second frame pieces 6/8” longer (3/8” on each side).

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • do you know what a backer-board is for?

    @ginoasci2876@ginoasci2876 Жыл бұрын

    • Reduces tear out.. should’ve had the scrap board closer to the fence during the cut 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Great video. Mic is to sensitive to background noises.

    @AAguilar74@AAguilar749 ай бұрын

    • Thanks for the feedback, I’ll aim to improve that in future videos 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop62889 ай бұрын

  • OK first of all I am just starting out in this woodworking hobby so I set up my bit that you call a that cuts the notch with the bearing just flush with the fence however the wood is getting burned so I moved the fence towards me as to make a smaller cut , same result The cut looks good wood is burned. Router speed is about 10000 rpm I was cutting maple. Any advice would be appreciated thanks much love your videos J

    @johnjaconsky4488@johnjaconsky4488 Жыл бұрын

    • I would make sure your bits are sharp, clean, and that your feed rate isn't too fast!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Did you just make the setup block?

    @sonicjihad7@sonicjihad7 Жыл бұрын

    • No, different blocks are available for the specific bits you're using. Here's the link! Set up jig blocks: www.rockler.com/router-bit-set-up-jigs-rail-and-style-bits

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Wawww

    @jamsheerkk2428@jamsheerkk24285 ай бұрын

    • 👍🏻👍🏻

      @mmcc_woodshop6288@mmcc_woodshop62885 ай бұрын

  • Good video but What do you mean the panel may need to be thicker ? I used every thing here and it cut 1/4" groove but 1/4" panel is not 1/4" thick how do you fill the gap to stop the wobble? Glue just runs out and makes a mess.

    @stacysmith7250@stacysmith7250 Жыл бұрын

    • Thanks Stacy! I didn’t have any 1/4” panel when I made this video - the panel I had was 5mm (a little thinner than 1/4”) so I was just trying to point out that you’d need to use a thicker panel than the scrap piece I had 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • The problem with these bits is that the groove the Rockler bits cuts is way too thick for a 1/4” thick interior panel to fit inside of without being too loose. You even mention at the end of the video “that would need to be a little thicker so that it doesn’t wobble around”.

    @MrLocke-bk3om@MrLocke-bk3omАй бұрын

    • The panel I had/was referring to was a piece of 5mm ply. The actual 1/4” panels fit perfectly in the grooves from these bits 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288Ай бұрын

  • Where is the description list?

    @brianduggan8739@brianduggan8739 Жыл бұрын

    • Hey Brian, what are you specifically looking for? The bits/tools are listed down in the description - if you’re looking for something else let me know and I’ll add details!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • 🎉❤🎉

    @samiadel7043@samiadel7043 Жыл бұрын

    • 👍🏻👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • You didn't use the sacrificial board on the coping sled as intended

    @TheTranq@TheTranq Жыл бұрын

    • Yep, I should’ve had the backer board all the way up against the fence

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • @@mmcc_woodshop6288 I’m using the Freud shaker bits for the first time, they’re slightly different from the rockler but hopefully can get these doors made

      @TheTranq@TheTranq Жыл бұрын

    • Those should work similarly! Good luck and hope it turns out well!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • Hello,

    @jeffbarneycastle9739@jeffbarneycastle97393 ай бұрын

    • It’s item #92013 on Rockler’s website

      @mmcc_woodshop6288@mmcc_woodshop62883 ай бұрын

  • You forgot the backer board to prevent blowouts!

    @ChefKevinRiese@ChefKevinRiese3 ай бұрын

    • Yep, I did. Thanks for the heads up 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop62883 ай бұрын

    • Dont feel bad. I just did the same thing TWICE!@@mmcc_woodshop6288

      @ChefKevinRiese@ChefKevinRiese3 ай бұрын

  • I like this setup, but adding up all the parts comes to about $1,200. That's a good chunk of change for a hobbyist woodworker, although I am about ready to build all new kitchen cabinets and doors. This would certainly make things easier and faster.

    @w9jim@w9jim Жыл бұрын

    • Hey Jim! I agree 100% Everything I have in this setup has been kinda of a 'one tool at a time' purchase. I've used the router table and lift quite a bit in the past but am new to the bits and coping sled (for this video anyway). It definitely makes the process easy to build them!

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • 1200 dollars you can own, a shaper but you need a router table for some tasks personally am confused about the investment the bits looks to be used up quickly yet they are expensive.

      @davidndahura7437@davidndahura7437 Жыл бұрын

    • I got a skil router table an router for 200 an cmt bits for 50$ cheap enough works great

      @jayhyde7987@jayhyde7987 Жыл бұрын

  • Here's a tip. Do your tendon cuts first.

    @pat199rick6@pat199rick6 Жыл бұрын

    • Cool tip 👍🏻👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • @@mmcc_woodshop6288 Thank you. Also, when you cut the tenons, put a sacrificial at the back of the cut. That way, you should get less spelching. As long as you don't move the sacrificial fence. It should be ok for all your cuts. Good luck!

      @pat199rick4@pat199rick4 Жыл бұрын

  • That backer board needs to be up against the fence. Its sole purpose is to be directly behind the end of your rail to prevent tear out. The way you have it set up (pulled back an inch or two), it might as well not even be there. It’s not doing anything at all. And… why do those bits even have bearings on them? They aren’t doing anything.

    @DMS20231@DMS2023110 ай бұрын

    • Thanks for your input and pointing that out 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop628810 ай бұрын

  • Sir, what happened to your finger? 😢

    @Vincent_de_Paul@Vincent_de_Paul6 ай бұрын

    • Just a small cut from something completely unrelated to this video. Finger is all good!

      @mmcc_woodshop6288@mmcc_woodshop62886 ай бұрын

  • What if you don’t have set up block. Spoiled

    @matthewhoheisel4840@matthewhoheisel4840 Жыл бұрын

    • Here’s the link to the set up blocks, they’re relatively inexpensive. Just make sure you get exact block that matches the bits

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • You will have chip out if the backer board is not right with your stile.Bottom line God bless

    @patrickarchuleta9594@patrickarchuleta9594 Жыл бұрын

    • Thanks for the tips Patrick - you're spot on! I've since adjusted that backed board for any future cuts

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • @@mmcc_woodshop6288 what do you mean could you elaborate? Sorry I’m a concrete worker trying to learn

      @martincampos5883@martincampos5883 Жыл бұрын

    • When the bit gets to the end of the board the part that gets cut will tear/chip out. If you place another sacrificial board up against the end of the board you’re cutting it will prevent tear out and leave a clean profile on the end.

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

  • WHY OH WHY Do so many you tubers start their videos with "What's up or What's going on " Arghhh instant switch to next video, it's so lame, how about some originality. What does it even mean.?

    @Paulgibbs99@Paulgibbs99 Жыл бұрын

    • Pretty sure it’s part of KZhead’s rules 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop6288 Жыл бұрын

    • Ohh that's a shame, I will have to start watching Rumble instead.!!!

      @Paulgibbs99@Paulgibbs99 Жыл бұрын

  • That router table is a pos

    @dwpalme2670@dwpalme26708 ай бұрын

    • Okay 👍🏻

      @mmcc_woodshop6288@mmcc_woodshop62887 ай бұрын
KZhead