💡 Restoration Of Old Rusty Air Compressor // Restore Complete Classic Air Compressor
2021 ж. 5 Жел.
1 931 644 Рет қаралды
restoration very old rusty air compressor machine | Nothing is impossible - restore capacity small air tool.
-Air Compressor made in Taiwan (star 1HP )
#NAME?
-Tank Capacity 2 Gal. (Can be customized)
-Motor Power 1 hp, 0.75 kW (Can be customized)
#NAME?
-Voltage 220V
-Maximum Pressure 8 Bar, 115 PSI
-maximum Speed 2880 rpm
-Noise Level with 80DB
#NAME?
I hope you find something useful & enjoy from this video!
I am happy to receive your feedbacks, advices, suggestions to improve myself.
During the actual repair of this cutter we also had a lot of difficulties and challenges because they were old, most of the plastic was weakened.
!!! I apologize for the mistake if I have made in this restoration !!!
Thank You so much follow me
It’s best to heat cast iron, then weld it, and immediately bury it in sand so it can cool slowly. That will give you a much better chance of a successful, strong weld.
I wouldn't trust such a rusty tank for a second without testing it.
I'd be more worried about what the inside of the tank looks like, than the outside. Somebody needs to track this guy down, and take that great big hammer away from him.
Will it hold up to a pressure test?
Так как ты забиваешь подшипники этим всё сказано ,какой ты мастер.
А также: краны наоборот поставил, фум лента под накидные гайки не наматывается такие соединения герметизируются прокладкой, съёмник за бортик ручейка а не за втулку - шкив обязан был лопнуть, на фоне этого покраска алюминиевых цилиндров нормальное явление. Такие ошибки простительны новичкам школьникам, но не мастеру который ещё и работу свою выставляет на обозрение.
ко всему прочему компрессор тупо не в ту сторону крутится...
Good job my Friend You forgot the belt cover Safety is verry importante
A little tip, when you connect the wires, put the cords in on the left side of the screws, because then the screws will pull the cords in, if you put the cords (as you was doing) on the right side of the screws, then the screws will push the cords out. By the way, a nice job.
apik tenan, telaten tur pinter
There was no inspection of the INSIDE of the tank. Air compressors are extremely dangerous as they can explode if rusted from lack of maintanence and care. Recently one of my cousins was killed by one of these. This is no joke!!!
I’m sorry for your loss I just attended my grandpa’s/PawPaw’s funeral by the time of me making this comment I know that feeling all too well but don’t let your cousin’s death pull you down he knows that it’s just fate playing it’s role and he sees you and your family are going to have a great life you deserve to have your cousin and you will have a great rest of your life Amen
ضضضس سيئة ڜڜشڜسسسسسسسششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششششڜڜڜڜڜڜششششڜشششششششششڜشششڜششششڜڜشڜشششششششڜڜشڜشڜشڜشششڜڜششڜشڜڜشڜڜڜششڜشڜششششڜڜشڜڜششڜڜششڜشڜشڜڜڜڜڜڜڜڜڜڜڜڜڜڜشڜڜششششششششڜڜشڜڜڜڜڜڜششششڜڜشڜششڜشڜڜشڜشششششڜششڜشڜشڜڜڜششڜششڜششڜشڜڜشڜشڜششڜشڜششششششڜششڜڜڜشششششششڜشڜشڜڜششڜششششششششششششششششششششششششششششششششڜشششڜڜشڜڜڜڜڜڜڜشڜڜششششششڜشششششششڜڜڜڜڜ
a
A fraudster and doesn’t care ⚠️, 😠
I’m sorry sir but pressure receivers air tanks do not explode due to rust in them. They always have rust in them. The only way an air receiver will rupture is in a overpressurization situation.
Great job new life to old compressor
عمل فنى جيد يستحق المتابعة
That's a great video. I will always cheer for you in Korea I'm looking forward to a great video. Have a nice day.
Hi welcome to Thailand ❤️💕💕
Like for the image quality
Agree with all comments. Heat a bearing , cool the shaft and it will drop on. Opposite for fitting in a case. Spent my life stripping and repairing well used machinery of all types, wish I had known about that magic spray that made nuts and studs free so easily when rusted in. Finally, hope the pressure test on that rusty pressure tank went well!. But interesting video.
まさに壊れたものを復活🎊 蘇らせるのってとても感動的です☺️
amazing work. thanks for sharing 🙏🙏👍
Conte conosco, José! Obrigado pelo trabalho, incansável! Que venha 2024 e seus desafios!
使用敲擊的方式來安裝軸承不太妥當
i like living...And I have seen rusty Air Compressors Explode!!
I rebuild compressors , and have done for over thirty years, looking at the way that pump is working, I would say that your not pumping efficiently, the valves need sorting out, it's only pumping at 55%
En apariencia es buena la restauración, en seguridad tienes parámetros de MUY ALTO RIESGO, nunca se vio que repusoieras la válvula de drenado en la parte baja del tanque además de que no verificaste el estado físico de las paredes para ver si resiste la presión...entre otras!
la supuesta capa de patina también es artífica o falsa, parece que le echaron sosa caustica para tratar de envejecerlo y oxidarlo a juro. el motor tampoco es el indicado, parece ser de muy poco RPM, con esas dos enormes cabezas de pistón debería cargar super rapido. ni hablar de cepillar con el cepillo de alambre los asientos de las cabesas de compresión. es simplemente un video para personas que son "entusiastas " de las herramientas, pero no para quienes realmente trabajan en las áreas tocadas en el video.
thank you
@@nito092 я думав що лише мені так здається
Fraud 😠
Great restoration. After all that I hope the tank is gd on the inside.
My man..hammering the bearing will damage it. And also the will dry out. You need to remove the plastic zo the bearing can get lubrication from the motor oil
That crack. You can just weld over it and grind it down, but it'll cause a vibration. Better would be to grind both sides to a wedge and close the gap, then fill it with weld and grind it smooth. That would ensure the roundness of the wheel and reduce vibration.
ષઠઠડ
Well done. 👍 Btw, thanks for not insulting our intelligence by showing a compressor that you "just happened to find" sitting in a field for years-but with green grass/plants still growing under it.
No hydraulic pressure test on that air tank = a bomb!!
not needed in Vietnam. If it works when u buy it, its all yours ! lol
This is 'Nam, baby!! No need to do it! 🤣🤣
,3misthemostpowerful @
@@ridhobaihaqi144 Hey, No problem. I'm in Cleveland and if it blows I'm safe.....But how 'bout the kids walking down the street in front of your shop or the people next door?
A fraudster and doesn’t care 😠
Nicht so ganz Fachmännisch repariert, aber der Klang ist geil. Ein Schutz vor Berührung vom Riementrieb wäre noch eine gute Sache
Lots of work but you never mentioned if you had the air tank tested to be sure it won’t blow from internal rust that all those tanks get over time.
An excellent painstaking restoration my friend as to the inside of the tank rust I'm no air compressor expert so I cannot comment good or bad but I felt you did an excellent job a very very time consuming job with an excellent outcome. It looked really good after you succeeded in restoring this old junked machine.
Niyamayi wede sahodaraya
What is the condition of the inside of the tank. Hope it does not explode some day.
Yo no restauraría un compresor en esas condiciones,es muy improbable,pero puede reventar..de hecho tengo uno de 50 litros que ya no utilizo por lo mismo..no lo tiro porque son muchos años y me da pena
13:14 make my day 😂
Góp ý ! Đầu fittings JIC thì không cần quấn băng keo trắng nha ! Chỉ có đầu NPT thì cần thôi ! Bạn google sự khác nhau giứa JIC và NPT thì sẻ rỏ ! Xài cho đúng nếu ko bị coi là thiếu thông minh !
Always put some oil on your Piston rings , will help with install and keep them from scoring at first start up.
You know to pull from close in to the shaft as possible. Unfortunately those old pulleys are brittle.
0:08 W tle rosną palmy, bananowce i jakieś tropikalne pnącza, a ludzie w swetrach, kurtkach z długimi rękawami... ciekawe, jak ubraliby się w naszym klimacie ;)
we come from Viet Nam
I love your signature colors
PARABENS PELO BELO TRABALHO Mustafa Zaidan { BRASIL}
Excelente muy buen trabajo
How were you confident that the tank would hold up to pressure after being allowed to rust away. No doubt there was water in that tank that evaporated. I wouldn't want to be near that tank when it decides that 175 psi is a bit too much
I almost became an air compressor repair man and builder but never was able to do it
I could see that pulley breaking. A little heat would have likely prevented that.
Loves battering stuff with the hammer ! ,and we all knew what was going to happen with the puller and the big pulley.......bit of heat and it would have fell off....
I do not understand much of these things, but I think It is a very cool job.
I don't know if it frightens the natives but, by God, it terrifies me!!!
super grate job dude
Did you pressure test that tank before doing all that beautiful work?
A fraudster…. 🙄 didn’t - ⚠️, 😠
Подшипникам конец)))
Khi ráp hoàn chỉnh r mà hơi yếu có thể chỉ bí quyết nguyên nhân k
good job
Bardzo super i idealnie jest to odrestaurowane pozdrawiam serdecznie 👍👍👍👍
I would use a new tank....
Автор, при разборе компрессора там были открытые подшипники, а при сборке запихал туда закрытые. Это как так и как они смазываться будут???
!НовьіеТехнологии
13:14 a magical moment
Always a rooster crowing in the background in these restoration videos
That’s not a rooster, It’s dinner,,
@@seadog158 like that reply.
Nice to see others like bringing back old like l,,, l just did a speedair 4 cylinder compressor puts out 38 CFM,, was happy to see American eagle is still making them and the compressor alone sells for 6000 dollars l payed 125.
HOW do you clean the inside of the tank?
Frumos, cati litri are butelia și în cât timp se umpla? 8 sau 10 bar?
В филме"Брильянтовая рука"бьiла реплика:"Надо бить силно,но внимательно!"Ето по поводу запресовки подшипники молотом.
Nice work on the air compressor.. I'll give you some advice, you need to restore that wheel 🛞 barrow the first chance you get, so you can haul more stuff home to restore...😊
Подшипники надо открывать и нормальной смазки туда набивать вместо силиконовой. И цилиндры хотя бы немного маслом смазать,перед тем,как поршни пихать.
beautiful job BUT. no pressure check of the tank??? it could become a large quantity of cobalt blue shrapnel. also no balancing of the drive wheel. if it's unbalanced it could tear itself apart.
Bravissimo 🙂
Nice work!! Awesome paint job!!
Muy buen trabajo❤❤
Are you going to trust that tank it will most likly explode from the pressure and the amount of rust it should be hydrostatically tested befor use
Compressor does not look old but looks like it has been in a corrosive environment. Cheap single stage probably thrown away when the valves went out.
Parabéns pelo trabalho!
घोठडठठठठठठछॅघडजटघठडठघटटटघोटगटघघटटजोओघघठठोऑघघटघघटिटटटटठोठटठजघघघघघघोओओओटठ
Que forma de poner un rodamiento..a base de martillazo ..adiós tolerancias y vida 😂😂😂 entre otras linduras ...
Excelente muy bueno 👌 👍 👏
все бы так подшипники напрессовывали😃
BUEN TRABAJO PERO TENDRIAS QUE HACERLE UNA PRUEBA HIDRAULICA AL TANQUE POR SEGURIDAD
Xomo es la prueba hidráulica, o es neumática?
Когда увидел как стучать по подшипнику. У меня случилось инфаркт.
Я этого не видел пропустил он давления не дает просто почистить и покрасить это не рестовратция обмануть себя церез пару часов работы масло побежит и расход электро энерги
Wonder how long those bearings are gonna last after that beating.
... and how a 2Rs bearing can be lubricated from the outside when the dirt guard is still fitted
@@peterp.1311 E
No doubt that was painful to watch
No Grease on the bearings???
Old air compressors are like ticking time bombs - you never know when they will go off. It's not a good idea to have a bomb near you... that's why you never repair an airframe older than 10 years. safety first!
New bearings destroyed on installation. One should only press on the part that is fixed.
Isso foi uma restauração verdadeira, parabéns, muitos mentem que restauram.
yes it is so cool
Pena que se nao sabe o estado do reservatório, se estiver muito deteriorado o risco de explosao e grande
@@lucianolopesdapaixao3990 من سوپاپ های مکش و فشار تیغه ای روی سر سیلندر و همچنین شیر یک طرفه روی مخزن و شاتونهای متصل به پیستون یک کمپرسور 400سی سی سه فاز را تعمیر و قطعاتش را ساخته و راه اندازی کردم و در حال استفاده از انم
THANKIOU
Very good
In fact the compressor is in good working condition only electric motor removed. no need to overhaul it.
bravo très beaux travail et belle réussite bonne continuation a bientôt et bonne journée :
Looks better than New 👍
Why you not removed the all ball bearing ZZ dust O ring OF THE bearing it will stop lubrication when you filled oil to compressor the oil will not lubricants the bearing and the inner ball bearing shall , it will the case overheating of bearings , and your compressor crank gets jarm so remove the bearing O ring seal when installing in compressor where oil lubricants the bearing.
46:24 Now that you watered the plants with green paint, they look prettier😂😂😂
good job.
27:41 thats that bearing destroyed.
Um excelente profissional abraços.
Meus parabéns vc é um excelente profissional adorei seus trabalhos ficam muito top👍👍👍
Thế thì ông 0 biết rồi,VIỆT NAM còn Cưa Bom,mấy cái này đâu xị nhện gì
Looks good , you need a one way pop off valve to relieve pressure on head for start up , the back pressure is fighting your pistons on start up.
٠
It's installed at 39:42
I never heard of a one-way pop off valve and I’ve been in this field for over 30 years. Please explain.
@@rotarycomptech actually called unloader valve, relives all the pressure from pump cylinders so it's not fighting pistons on next start up,, always placed in pipe from pump too tank also keeps pressure from leaving tank going back to pump.
@@georgespangler1517 oh wow thanks for the information I didn’t know that.
Muito bom 👍👍
If the tank is heavily rusted on the inside that thing is a timed bomb.
No, it’s not
No, it’s not
@@rotarycomptech yes it is
@@necsoiub i’ve been in the field for over 30 years air receivers. Do not rupture due to rust. Sorry it’s always over pressurization. The tanks are always full of rusty water and rust. Do you really think a tank manufacture is going to make a tank that’s going to rupture because of rust being in the bottom of it. If this was the case, this sure would be happening a lot but it only happens to a very small little air compressors why? ? The little compressor is running along and it’s starting and stopping using the pressure switch contacts.then one day the contacts weld them self shut or closed. Then you have a runaway air compressor. The only thing to keep the tank from exploding at this point is the pressure relief valve. If that fails, the tank will explode or maybe the discharge line might blow off to save the tank from exploding and that is how that happens.
Не накачивает полноценно, либо обратный клапан либо прокладки, плюс пластины клапанные не очистил...
công việc tốt
That compressor is not safe to use. Under pressure that old rusted tank can explode.
Typically the tank will rust at the bottom from the inside out. There is a drain valve at the bottom to drain water that condenses in use. Even so they will rust. The compression may look like new on the outside, but it could literally explode like a bomb !
Totally agree, Used tanks should always be tested. I always would test used tanks with hydrolic pressure (water) to factory specs and insure they hold pressure for several hours.
That receiver could be dangerous, I would never use anything like that without a proper pressure test
Sorry sir but tanks don’t explode due to corrosion or rust. It’s always over pressurization that causes them to rupture
Are you serious! A pressure vessel has to be tested (hydraulically to at least its rated working pressure @@rotarycomptech
@@johnwilson6298 yes I am serious and yes I was in the field for over 30 years. I know what I’m talking about.
Good hit 👍🏻👍🏻 🇮🇳 || Kuki 06|01|2022
Después de todo el trabajo realizado, creo que sí se merecía unas terminales para conectar el cable en el presostato.
Seriously, who cares about all the unbolting and rebolting? It was a bit tedious. The actual fixing is more interesting. For example, how did you inspect and clean the pressure gauge? Also, sorry about your busted pulley, but anyone could have seen that coming from a mile away.
Muito Bom, Parabéns
Very nice job 👍