Hey guys so here is a nice little repair of a worn skidsteer sweeper bucket bottom. These things take some abuse because of not being able to inspect them as easily as a regular bucket. In any case, I hope this helps and I appreciate the support.
Here is a link to some of the tools I use
amzn.to/3TnyFdv
Just wanted to say THANK YOU! you are letting us learn so much over your shoulder! Amazing work as always. I think I can speak for us all and say that we appreciate your videos!
Well said! Couldn't agree more! Thanks, Isaac!
Thank you for making us feel human. Showing the first and second cuts, why you would do it differently and then just the silliness of forgetting your supply was under the table makes us all feel normal. You help us all feel like we can try some hard work, screw it up, figure it out, and move on. It is inspiring.
Bringing you a completely sandblasted bucket and precisely pre-cut plates to add to it -- there's someone who respects your work and your time, I'd say!
Smart guy has probably been around the block a time or two. Not many of those around.
Sometimes it means they want the cheapest work possible. Not saying this is the case but when customers ask me if they can prep parts, or come help me in the shop to do the job, they never accept the bid.
@@jtlpwilliem yes, most of the time its because they want to save a few bucks but watching this guy and knowing how good he is, they most likely wanted to save HIM some time because they already know what top notch job they are gonna be getting!
Your repair skills made the job look easier than it was. Your camera work and editing skills created a "how to" video that will allow anyone to duplicate your work results. I count that as two highly developed skills. No wonder you have such a great You Tube channel. 😎😎
I could watch you work your “Magic” for hours on end, ISAAC! ALWAYS, lessons learned by me, from your knowledge and experience! THANK you for sharing, and always “schooling” me in my craft and practices! Truly the BEST! ⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️
Perhaps this bucket wasn't the most complicated job for you. But no matter how tough and difficult a job gets I love your attitude " No biggie we'll fix it". Wish I could have more of that. As always, keep them coming. Love everyone of them👌👌👌
There's Isaac . I was getting a little worried . :)
I learn something, or two every time I watch Isaac . Thanks one more time . :)
Its always good when a old dog learns a new trick or two!😀👍
I love the way this channel and CEE complement each other. I don’t watch any other engineering channels
Try snowball engineering hard working clever guy. Good luck
Snowball Engineering in UK is another awesome channel to learn from. Same with IC Weld he show the jobs from beginning to the end with success and mishaps included. WatchWesWork gave him (Oliver) a shout out because of Oliver's great work. Oliver is young but work hard to make great content.
Once again you make repairs look like they are easy! Sequencing, heat, and skills from a seasoned professional is evident. The cleaning was a break, as was the shearing and hole punching…….but it’s faster and less expensive when you have multi thousand dollar tools in the steel supply facility. Allowed you to do what you’re really good at without the grunt work. Win - win!😊
If you only had more customers like that, he got the bucket sandblasted, it must have looked horrible before he took to you. Badass video.
I was thinking the same thing. It's nice when the customer helps out with the prep work before he sends it to you. Especially with it all cleaned up and sand blasted.
You work magic, my friend. It's a pleasure to watch a good tradesman at work. From one to another, it is always a pleasure. Maybe one day I'll upload some auto mechanic stuff, but there's already enough of those guys.
Always enjoy watching Isaac he explains how and why also not scared to show things that go wrong . Thank you for showing us your trade
Great job getting this customer fixed up. You do awesome work.
Man I learn so much every time I watch your videos. Thank you Isaac for your contribution to this community
*I C Weld* Bravo well done, always a pleasure to see another video, thank-you sir for taking the time to bring us along. GOD Bless.
I know the feeling, I am always getting in my own way when doing this sort of job. have a great day and keep the videos coming78 yrs. old retired and loving it Michigan.
Your Skill and experience shows in your amazing ability to freehand and make everything seem so easy. Well done Sir. Thank you for sharing your expertise with future welders/Fabricators.
Great Job Isaac ,When I get one of your New Video to watch I tell my Wife ,My Welding Class is about to Start ,thanks again I really enjoy watching you do your Magic ,and ad a Good Laugh today when you said and My next trick,,,,,
Nice work turning a piece of scrap metal back into a bucket.
As always Isaac. Your work is awsome !! Love the lessons !!! I sure appreciate your guidance sir. Thank you
Don’t understand why anyone that has watched more than one of your videos wouldn’t subscribe.
👍👍Agree
🤣
The Rain Sound Just Add's To The Atmosphere Man.........................
Well a simple yet straightforward repair made easy with a great tutorial on not how to but how you do it . Many thanks for having us along as you go I'm sure a lot of us watching have learned a lot and with at somepoint use the knowledge.
I'm not a welder Isaac, your videos are always, interesting, informative, educational and entertaining. Thanks for the time to make them. BTW my uncle is a welder/fabricator, old timer off the boat, told him about you on utube....he said "u tube ? U is a channel, NOT a tube, whatza mader U!" 😂😂 He turned 85, on the 23rd, still tinker, does "hard welds" for my brothers landscape business, he loves it.....says it keeps him sharp.
Was really nice of this customer to sandblast it and supply the steel with the scraper edge holes already put into the steel like that. Definitely made your job a bit easier for you for the customer to do that. Too bad all customers weren't as considerate.
Better than new at @ a quarter of the price. Fun video. Thanks for posting Isaac. Steve
As always it comes out as a WIN!! Nice work!👍🏼😊
Nice job your videos are always a lesson
Another work of excellence out the door!!
Good video as always. You may already know this but because the way the plasma swirls, the cut will always have a good side and a bad side. The good side being more square. The good side on most machines is the right hand side of the torch if the direction of travel is considered the front. So if you're pushing it away from yourself, the right side is the good side. If you're pulling it, the left (your left) is the good side. Left to right movement, good is near side. Right to left, good is far side. Doesn't matter the handle orientation. Just consider the leading side the front. Doesn't matter much on n thin stuff but it can help on thicker. With some machines it's more pronounced than others.
Always good when a different type of bucket comes in for repair, something new will always be learned. Top stuff young man!
Thanks. I'm not a welder just a guy that own a couple of them and like to fix my own junk. Always helpful advice in your videos.
Very nice job Isaac and nice little tip with the wedgey strut. Thanks for sharing
Another great class on fabrication and welding. Thank you Isaac for sharing your knowledge to us home shop guys.
For my first trick! Always a sense of humor as you approach your project! Anther nicely completed project,
As always Isaac, excellent work. You make it seem so easy.
Excellent work as usual!
I found this channel this evening, and want to say thank you! I'm a homeowner who likes to make and fix things (mostly for my tractors and implements). I'll be checking your other videos.
We can always count on you to teach us some new tricks, Isaac! Thanks very much. The videography is great as always, too. Hope you have a pleasant and peaceful weekend.
Amazing trick to keep the center from bowing awesome work as always Cheers from Nova Scotia
Evening Isaac I could not belive my eyes when I saw you use your plyers for there proper use! I thought they where your go to Hammer, Scraper🙂 nice to see you back on after such a long break. Regards Richard 🇬🇧
Isaac it’s always a pleasure to watch you work you’re an artist when your own way you never give yourself enough credit I learned a few tricks overexpanded take the belly out of it new sweeping bucket from bobcat I think silver 42 or 4500 bucks depending how wide they are I wouldn’t be afraid to buy an old one and rehab it like you did by the way I like your gantry how wide or should I say how long is your bottom span where the wheels are I’d like to build one and you’re seen the role really nice without any tipping could you just shoot me a bottom measurement of that where the two rollers are I don’t wanna make it too short so it’s tipsy and I don’t wanna make it too long like a tractor trailer but your seem to work well I’m the guy who sent you the rags Sam bacon do you know who I am and you take care get the kids some more videos I always enjoy your comments be safe take care stay warm your Yankee friend from New England bye
As usual, excellent work and teaching! We are learning a lot from your videos!
As always artistry at its finest. Thank you for sharing.
Thank you Isaac. Man that looks good😊
Always something to learn from your video, Always good!!
Take good care of those customers that bring clean parts ,they are keepers. Phil
Thanks for all the great videos, I enjoy watching your projects so maybe someday I'll know what to do when I have to fix my own stuff 👍
I always enjoy and learn from your videos. It doesn't matter what you are doing or if you've done something similar in the past, I'll always watch. Thank you!!
Yeah there was a nice little job. I like that. I like that tip you got on your plasma cutter makes it a lot easier. Yeah it was nicer. Sandblasted that's for sure. Yep the owner that'll be happy. 👍👍🙂🇨🇦 0:30
IC your attention to some of the simplest details is unmatched
Another great video. I like the way you explain what you are doing
Nice work Issac! My first welding experience was hard facing skidsteer buckets! Man what a throwback.
Already subscribed. Here's a comment for the algorithm. Thank you for the videos.
Nice crisp work there brother that plasma shines on rebuilds like this ✌🏻
Your skill and experience are nothing short of awesome
parking your project on top of your stock sound like something I would do. lol
Great Job!!! .. Indeed it looks brand new!! :)
Awesome as always. Thanks for sharing all the wisdom!!
Wow, you working on something I've done! Didference is i get them half full of mud and grease and fully assymbled. Half the work is getting them maneuvered to work on.
Looks good, amazing workmanship
You make this look very easy. A real Pro! Thank You.
Isaac that’s was a beautiful piece of work 👍cheers from California
Timely video Isaac, my farm tractor's bucket will soon have to have work similar to this done to it too. Yes, I have learned a couple of tips from this, and for that, I thank you.
Looks good to me. another fabulous job finished.
Always a lesson. Thank you.
As always a great looking job
always great content Issac......cheers from Florida, Paul
Yep I learned something your a better welder than I am. LOL
First 👍's up IC WELD thank you for sharing 😅
Thanks so much Isaac.
Nice shooting as always.
Someone did that exact thing to my sweeper bucket. I repaired it the same way. Fun ny!
Love watching you ! Just wish you were around to teach me when I was young . Was no you tube waaaaaaay back then . What I learned was in ag class a few hours way back then . Was no plasma or mig welding either just stick . A lot has changed in 60 +++ years.
love your videos, makes me jealous you get to do this for a living
Top job as always Greetings from Ireland
Always enjoyable watching your videos!
and who cares what a trumptard thinks... Nobody but their echo chamber.
Fantastic repair!!!
Awsome video ,great commentary ,safe travels . Thx for sharing bud🎉
Great video Issac and great learning experience with the different tricks for keeping things square.
Love the videos always a great watch!
Looks real good thanks for sharing your work and knowledge.
Nice job as usual. Very well explained, executed, and nice welds, by the way.👍 You said you're not keen on plasma cutting because they don't cut straight. Steady on there, fella. A skilled tradesmen like yourself never blames his tools! You are new to plasma cutting, so more practice is required on your part. You will soon make every cut straight. Trust me, it took me about 3 months before I mastered the art. And that is exactly what plasma cutting is. It's an art just like gouging or welding is. Remember the first time you gouged out welds using carbon rod, or gas. The mistakes you made, or how bad it looked? Do you remember when you first cut sheet metal using a torch and how crap it looked? Or what about the first time you used a stick welder? I bet that looked like bird droppings, am I right? Because mine did. I hated using a stick welder but perseverance pays off. Stay with it and test how each cutting tip reacts in different scenarios. See how different thicknesses of sheet or block metals react. You may be surprised that one tip does not cut as well as another one does on different materials. Also, the guide you used. It seemed to look more worn on one side than the other, or was that just the camera angle? In any case, it's much better than the clear plastic one, which came with my first plasma machine. Admittedly, it was cheap but still worked well. Another tip is your cutting technique. You will find it best pulling the torch towards you rather than pushing it away from you. Sometimes, slag can pop up into the path of the flame, causing it to wonder. The end result is a wonkey edge. I know, I learnt the hard way and some of my mistakes cost me money! Also, there is the safety aspect to consider. Once, I was cutting 3/4 inch thick sheet of steel. It was 8 feet long by 4 feet wide. It was cut from the hull of a ship. It was so heavy and me, feeling lazy as usual, I pushed instead of pulled. Suddenly, an explosion occurred, causing molten metal to fly across my shop, hitting my daughter in the face. She was sketching me at work for a school art project and sat 20 feet away. Never the less, it left her with a scar the size of a baked bean on her cheek. Safety first, always, as you never know what may happen. When can we expect a big job. One where your video is, let's say, an hour long?😁 Do you know what would be great, for you to upload 2, no! 3 videos a week🤘🇬🇧🇺🇦⚒️
😮Wow. Says video was released 14mins ago, and 620 views already. That's pretty crazy! Good job Isaac!👍🏻👌🏻⚡💥⚠️🚧🦺🚜🛠️🔧🔩
Never take KZhead statistics as facts. They can be all over the place and are totally unreliable. 😅 Mark from Melbourne Australia 🇦🇺
Great job.The only thing i do different is cap the outside bottom seam with hard face and hardface the wear strips.
Thank you for sharing, I learn a lot , 👍👍👍👍
Thank you for your Videos!!
You most definitely take pride in your work just like you take pride in yourself hoorah
seams are perfect
Awesome job like always! Thank you for sharing!
Kudus on repairing it but I'm surprised he just didn't have you build him a new one.
Great video as always.
I've been watching your channel for some time now. You get a lot of positive comments on your welding and techniques. You'd do well starting a 2nd channel with welding classes.
While I agree with your comments, I would say that Isaac has enough on his plate already. There is is mobile welding business, teaching his son, doing the bookwork even if his wife is doing the majority of the bookwork lsaac is still responsible for the facts and figures. Then there is this channel as well as some pod casts! After all of that Isaac does need some time off for rest and recreation and to spend some time with his wife and family. My apologies to your wife Isaac as I don't know her name! 😢 Mark from Melbourne Australia 🇦🇺
I wish that I could have been his apprentice!
A scrap yard bucket and Issac what do you get a new bucket. Great job
That’s a killer standoff you made Isaac. We always enjoy your thought process and learning how you tackle these projects. Much love from Htown.
Great job as usual!
I've found that #2 welding glasses works good with plasma. It lets me see the flame without burning my eyes.