iENYRID M4 PRO S+ Electric Scooter Review & AKASO EK7000 PRO Action Camera + V50 Microphone
2023 ж. 5 Қаз.
1 553 Рет қаралды
@iENYRID @akasoofficial @slimeproducts Updated description on iENYRID M4 PRO S+ Electric Scooter regarding best voltage performance (54v to 46v), charging etc and showing small detailing I've added for a personal touch. You get 2 miles per volt on non-stop full speed before speed reduces under 46v ( just over 16 miles ) until battery goes at 39v ( 20+ miles ) ...Be safe and be well
Good video... Is there anyway to turn off the green/blue/red side lights... ?. I like the idea of the front and back lights, and also the indicators... but the side lights might be a bit too bling for me!
Thanks, no you can't turn the disco lights off or have set on one colour which is a shame. You can disconnect them if you open up the panel areas and they are only adhesive stuck on led strips, or just put some black tape over them will hide the horrible green/blue/red flashing Hahaha....I just put some red film over them which makes them less flashy by making the colours purple/orange/red which is in a video on here
Got the same scooter, I got a puncture going over a cattle grid at full speed. I got the proper inner tube off eBay. Have you got a link where I can buy the solid tyre please. Let us know how you got on putting tyre on cause guy in shop told me it’s not easy. It’s a good scooter on the roads and pavements but not off road. Good for climbing hills to, I’m 14 stone and I get 27-28 mph on straight road no wind. Being 56 yrs young I cruise about most of the time I’ve already fell off a cpl times lol
Hi yea them cattle grids will do that, I have gone down a steep hill knowing it's faster then top speed when it shows 27 but the display never shows higher. I'm about 16st and depending on wind and terrain it does reach 27 too. Yea the solid tyres it says put them in hot water for 10 minutes so there easier to get on but I looked earlier and although they are the same size as the ones the scooter comes with the lip of the tyre that lock's behind the wheel rim is 6.5 and it needs to be about 5.5 so I'm sending them back to Amazon...I haven't found any solid ones that should fit from searching the web yet but so far I think using that slime inner tube sealant is doing the job of not getting punctures so if I was you I would add some in your inner-tubes....I did use the slime with a red label on it, about 60ml (2oz) per innertube but earlier saw there is a black label called slime 2in1 that works on bigger punctures so I'm getting that and some spare inner-tubes if I need them for finding solid tyres to fit might be hard from what I've seen...and check tyre pressure is atleast 40psi max 50psi every so often so that tyres don't get a pinch puncture...I did order I standing pump off Amazon with psi meter because my bike pumps one is hard to see when using it.....other then that, yeah it's a good scooter and the upgrading of the controller from 16ah to 20ah iENYRID messaged me back saying they don't recommend it although not sure why since the +MAX version is basically that...upgrade of M4PRO S+
@@TenchuDRAGON thanks for reply, guy in bike shop who fixes all the kids punctures including mine said you need a machine to put a solid tyre on? My mate who’s a tyre fitter said he wouldn’t even wanna attempt it, I dunno why he does it all day everyday. The puncture I got was a pinch and it went down immediately, I think I will get some of that stuff. I never knew what pressure was in them from new they just seemed solid, I might invest in a battery pump to. Some guy on here said he puts about 45 psi in his. It’s great little scooter it gets me around, I don’t bother with the seat. I thought it was ok to put the 20ah controller on it? Think I’ll wait for some advice on that. Thanks for advise mate 👍