Extremely rusty car sheet metal repairing
In this video I show the repair of the extremely rusty threshold in my car.
The car is a Mazda 323 2.0 DiTD from 2001.
It is commonly known that Mazda has problems with the rust on the sheet metal, so see this video how to fix these flaws.
I've spent about 5 hours of work in the repair for a few days, which can be seen in this video of 15 minutes.
If you like the video, just click on the like button and, of course, make a subscribe to see more of this and similar stuff.
Don't forget to check my other videos!
You can check how it's turned out one year later on this link:
• Threshold rust repair ...
You can check how it's turned out two years later on this link:
• Checking the threshold...
Music from the video is:
Track: Tobu - Turn It Up [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Tobu - Turn It Up | Tr...
Free Download / Stream: ncs.io/Tobu_TurnItUp
Track: Star Party - Legends [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Star Party - Legends ...
Free Download / Stream: ncs.io/Legends
Track: Last Heroes x TwoWorldsApart - Eclipse (feat. AERYN) [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Last Heroes x TwoWorld...
Free Download / Stream: ncs.io/EclipseYO
Track: NIVIRO - Flashes [NCS Release]
Music provided by NoCopyrightSounds.
Track: Domastic - Khalas [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Domastic - Khalas [NCS...
Free Download / Stream: ncs.io/Khalas
#rust #repair #howto
@MCTutorialsOnline
It's his first repair job. You gotta start somewhere. List of possible ways to improve: - use heavier sheet (welding sheet that thin is difficult for even a seasoned welder) - make butt joints tighter - use magnets to hold the patch in place for tacking it - weld all the way around - get a DA sander - use a flex sanding disk on the grinder to feather out - Bondo isn't intended to be structural; use long strand fiberglass, or fiberglass mesh and resin to span gaps - use a 'cheese cutter' body file to rough shape bondo BEFORE it has fully cured. - use a long 'block' to retain a flat plane surface - sandblast, or use Por15 or other to 'freeze' rust, and slow it's return - That's all I can think of. Good for you for undertaking your first repair. One difference between my first repair and yours is I didn't show the whole world🤥
Thank you for providing constructive criticism VS all these other guys just saying "bad repair!" super helpful.
@@JoeUrbanYYC Thanks. It's better to be open to improvement than pretending we know it all. That is how I try to do it too.
I was about to comment the same thing but you beat me to it thanks for letting him know im gonna like this comment because i hate seeing negative comments get the most likes and good advice get the least...people piss me off
Eu não entendi o que você falou kkk
With how much information is out there these days I think there is no excuse for incredibly poorly executed work. This was just a lazy / sloppy repair. It is better to fail trying to do the best job than to fail trying to do a sloppy job.
When I was a very young man, that was the only way that I could afford to do bodywork on my cars. It was inexpensive and strangely lasted for many years. I have since grown older and I now have all kinds of expensive welders and different types of sheet metal in my workshop. I am grateful for the prosperity that I worked so hard to attain. Life has taught me to fix almost anything and make it look professional as I finish. You will also aspire to where you want to be in life because you are not afraid to try. Good job young fella.
Leider keine gute Arbeit. Nicht komplett verschweißt, viel zu dünnes Blech. Von der Spachteln Orgie kaum zu sprechen. Sorry das mach ich mit meinem 140 € Schweissgerät (Fülldraht) besser. Für TÜV mit großzügiger Kaffeespende reicht es.
Egal nach 14 Tagen fahren siehst nichts mehr von durchrosten 😂
@@pw8526 Pfusch bleibt Pfusch
Como puedo conseguir una soldadora como esa , yo vivo en Cuba
@@heinzgeorgspengler-ob8ux si tu sais faire mieux n'hésite pas de nos montrer une vidéo.
3.3 million views of the sloppiest body work I've ever seen, THATS AMAZING!
The worst job I've ever seen. The way you put on bondo more like a novice pastry student
A good laugh
His taste in music suggested a great deal about his ability. A quality repair takes time, effort and attention to detail. The music he decided to dub over this is a sign he has none of these things.
Wow, I hope people dont think this is how you do the job correctly! I could write a paragraph of everything you did wrong but im not going to because it would take too long. But kudos to you for getting out their and doing your own repair. You will learn and fix mistakes with your future repairs.
I was thinking at least put a layer of fiberglass over it to hold it all together before the Bondo
Hola.veo que entiendes del oficio !!.solo por tu comentario.deves de saver.yo con ver la herramienta que elijes se lo que saves.
Probably one of the worst repair jobs I have seen...seriously..
Pahahaha 🤣 yeah it was pretty bad, but I bet it passed the mot
good enough for an old beat up car
@Wayne Galvin Check my new video of repairing rust on my car! kzhead.info/sun/h5iImZVojquAooU/bejne.html
What would you do differently? I need to do similar job on my Burak
@@DaveDude he did ok but after cleaning and cutting out rust u need a good rust protection then get sheet metal and cut that spot almost perfect then well the spot then get a high grit sandpaper and sand well spot then potty, sand it and prime then paint
I watched over a hundred videos to learn how to repair the rust on my car and this video is the best because its closer to reality than what I saw in the other videos.
😂😂😂 a "screw it, it's getting dark. That'll do" job
HUGE GAPS IN THE THE PATCH .. FUCK IT ILL FILL IT WITH BONDO
you're far from reality then lol
You really found worse repair videos? Can I see them?
Wow, everything from wrong methods to wrong materials in one shot. One of the better used car lot scam fix's ever seen. Congrats!
😂👍
this looks like typical gypsy body work scam. they roam parking lots to look for victims with dents. it's real bad in Oregon and Washington. everyone on Oregon and Washington know never but a car truck or rv from a gypsy car lot. guaranteed rip off.
Какой правильный комментарий.
Great video for those that know the struggle. Just looking to pass a saftey inspection
Excellent although there all kinds of different ways to do things ! Your video gave me a good start point of the concept and when I attempt my Job on my Project I will do the best Job I can and it all depends on how much you want to put in the vehicle to sell it or keep it !!!👍👍👍🙏GOD BLESS US ALL SPREAD THE LOVE..💕🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸
Дай Бог тебе здоровья и побольше работы. У тебя есть, значит и у нас будет. Надо же кому-то потом все это восстанавливать.😄
ну, кровь из глаз... как по мне уже лучше бы стекловолокном и штаклей подлечил бы порог, чем этой фольгой... как я не люблю после таких деятелей переделывать, это капец...
угу сейчас он ржу попрячет, а к тебе клиент приедет рыжик подкрасить, ты его ковырнешь, а там все авто в труху
Leaving large gaps between the metal sheets will make the filler to crack at some point, therfore the repair is temporarily. The metal sheets must be well welded to the remaining body and cover the entire gap.
FUCK IT.. FILL IT WITH BONDO, ITS ALL GOOD, IT FIXES EVERYTHING . LOL
@@mikeroberts3660 i know an even far more worse way to fix it, and that is that i would have left the rotten pieces on the car and glue a piece of wall paper over it and then paint it and job done!
Its not a repair...its filling a hole with crap
Every time they remove any trash or dismantle a part I keep on getting scared that a snake is likey to slither out from them. I appreciate their patience and hard work though. This one of the best restoration videos on KZhead I've watched so far
Need to weld those patches all the way round, then use a waterproof filler with fiberglass strand, especially in an area that may see water infiltration. Then finish coat with light body filler before epoxy primer and finish coats. It’s a good effort, and it will last a while, but definitely not permanent. Decent job considering. 👍🏻
Hi, thanks for watching. Thanks for suggesting on repair. I will consider this option in my next repairs.
@@MCTutorialsOnline Next repairs? Are you selling these cars then? Dude, you should not repair cars because you are not suitable for the job because you don't have the patience, interest and therefor not the will to do it propperly. You have all you need to fix this job, except the sheet metal you used was way too thin, but all the other materials and tools are the same i use when i would do a cheap fix like this. So it's not the lack of knowhow but the lack of interest in fixing cars i see in this video, because you sure don't have any.
It's not what I'd consider a "permanent repair", but a 2001 Mazda 323 is not exactly a rare and valuable car that you restore in order to keep for the next couple of decades; it's a beater that just needs to get you through the next couple of months (or years). The repair looks adequate for that. In a couple of years, he can get something like a 2005 Mazda 3 for the money he'll get from the wrecker when he trades that in...
@@peterjohnson9438It might not have the highest price tag, but for some, your car is your car, and you just want to fix it.
He's not a tradesman but at least he's giving it a crack!! Good on ya mate.. 👍🇭🇲
Руки то у тебя золотые! Вот плохо,что растут не от туда.
You make it look easy, good job
* sees jack stand placement * -ahhh, one of THOSE videos
Круто! Получилось гораздо лучше чем было! Минимум времени-максимум результат!
Гавно это а не ремонт.
Quick tip for anyone welding thin sheet metal: Instead of trying to put welds in the space between the sheets, try welding onto the tack weld itself. It makes it harder to burn trough the sheet. Also, if your gonna weld all around a sheet like that take into consideration that the metal might warp and bend from the heat.
stitch welds
@@galehess6676 Right. Stitch, and maybe alternate between sides in order to allow the seams some time to cool.
This technique also works with aluminum if u have a shitty rig
I am not a professional whatsoever. But when had the same thing I made it in two steps. One, I have added in the upper side one thin sheet of metal so the patch will sit on it. Made some holes through the rocker itself and welded through those small holes. All parts were treated with special welding spray for corrosion inhibiting. Then added the patch which was also drilled and made spot welds on the extra sheet. Only after made also spot by spot welding the entire panel with the air gun blowing cold air and never one near each other. One on the left one at the right and with closing the gap the time spent blowing air was bigger. I have considered the rocker panel has structural importance and therefore thought it made sense. Any welded part is not like a full sheet of metal. In the end I sprayed rust inhibitor inside the panel and after few days some special wax with a specially nozzle. Outside was sealed using 2k epoxy. 5 years has passed and believe it or not, I still do not have rust in that area.
Great video, from start to finish. Thanks!!!
Hi, Thanks for watching and supporting me in my work.
I don't think the comments were hateful, just telling the truth. That was a really bad repair job but no doubt be did his best and good luck to the lad.
If it was his best, than what would be his average? I would not want this for my truck
Ive seen worse on a transit van the previous owner stuffed rags and stuff on the sill and body filled over them i dont even know how it worked but it did literally no structure to it tho it cracked when we jacked it up 😂
He has very poor tools ,so can't criticize his work.
@@UncleRobsGarage ive seen people do better with spit and copper. That being said this person probly doesnt do this for a living. They had all the proper tools just not the skill. Fun to watch though
seriously you helped me out big time thank you for the video! Its quick, easy and effective. That's all I can ever ask for when it comes to a DIY video.
And also illegal in most parts of the World that have road safety tests. Seam welding required at every non original join. Bottom was originally spot welded and plug welding is a usually acceptable alternative there.
En que te ayudo ??te mostro como No se hace el trabajo
Nice music choice. Gotta love how bass music is working it way into blue collar how to videos.
Great video, helped me repair my rockers as they were getting bad! Question, did you use gas euth your welder or just fluxcore? Keep up the great work!!!
Hi, Thanks for watching. I'm glad that my video helped you! I used only flux core welder.
Most of us obviously haven't taken the time to record and edit a video of ourselves repairing rust and upload it for everybody to criticize, so I have to give some credit for that. It does look great, but I'm definitely not a fan of this method and I don't think it'll yield any long term results. Ideally you'd have the patch fitting like a glove before any welding, then weld completely around the seam leaving no gaps. Personally I prefer to use "easy grind" wire because it'll leave a softer weld that's less prone to cracking paint/filler and is still workable.
most of us who have not uploaded a video on this type of tinkering, had probably made proper self evaluation.
Не дай Бог попасть к такому мастеру!
Совершенно согласен...😄Чего он сэкономил он сам не понял! Но зато после таких горе мастеров у нас всегда будет работа!
Trebuia să sudeze toată tabla care o puso,apoi să o şlefuiască să îi deie restul chitul de încarcare apoi de finisare,dupaia un grund si apoi vopseaua.
the work is skilled the results are good, very impressive
These days, any video that just starts with exactly what it’s captioned as. No “hi I’m Sir Nobody will remember your name, and today I will be showing you…” Gets an instant like and subscribe from me. Plus this was a great video too.
This “tutorial” should not be followed by anyone.
Hi, Thanks for watching. Hope you enjoyed. You can check video one year later. Subscribe for more. @Bob Vel please show me some of your work so I can learn how it's supposed to be done.
Agreed
Hi there, thanks for watching my video. I actually live in first world country. Also known as western world country!
@Tayip Erdogan I don't live in Russia. Don't know why you think that I'm from Russia. As I said I'm from western world countries. If you check some other comments you can find were I'm from.
@Trae Townsend Hi there, Thanks for supporting me in my work.
Good video.thanks for posting.
Hi, thanks for watching!
Thats the most profecional patch panel i have ever saw it should last a life time .keep it up and see where you end up.
It looks very nice to me. Great job. I also like the tips and advise in some of the comments here. Awesome.
Не позорься, не выкладывай такую шляпу.
Porr
Это ж не его машина)
Слыш ты хотя бы провори нормально, хули ты точками приварил
Дошерагами и супер клей и было бы лучше...
Я такого пиздеца!!! Ещё не видел!!!
Dam I was going say nice work until I seen you put the putty on without welding the sheet metal and sanding it after acouple months that will crack if your going do something and spend money on it then do it properly to make it last
Why is everyone disliking the video like it was misleading lol? 🤨 He clearly just showing how to replace a rusted part of the car
I was told I have to use same gauge metal as what I'm restoring but I see you use Bondo too so it must hold better with sheet metal .. I'm working on a 1960 valiant I have to do a piece just like this thanks this really helped I've never done it before this helped a lot
Hi, Thanks for watching. This was fast and cheap repair. If you want good and quality repair you need to use same gauge metal. But as you see this repair is still permanent. I'm glad that I helped you with your repair.
Don’t use bondo, it’s cheap but takes away from the cars structural integrity. It’s not designed to cover metal. Hence why when I go buy a car I take a magnet with me.
There's a professional restorer I watch on here. He uses 18 gauge for everything with is thicker than standard body sheet metal. He likes it because he doesn't have to worry so much about grinding through and it's easier to weld. My Honda is mostly 22 gauge which is thin as paper. I used some 20 gauge for my repair on the Honda.
its nice to see a consumate professional in the car repair business, a man with the knowhow and skills to repair such a badly rusted vehicle, a pleasure to have been privelaged to view this,
Surely ur taking the piss
@@weekendworkethic6177 well maybe a little bit maybe!!!!!
You lost me at 7:35 with unfinished welds with large gaps in sheet metal with body filler being applied to cover it up. That is not quality work and it would not have taken much but time to finish it correctly. This exposes the metal to rust again.
So true... he could have filled that up...
So would this be correct as long as it is completely sealed? Or what else is wrong?
@@marvino7132 well... having a weld instead of bondo is 100% better . a lil rock cold damage that area and you'd loose all the hard work cause u saved 1 extra minute of welding.
What im saying
@@marvino7132 when the panel was cut out and the rust behind it was exposed it could have been treated with rust stop or encapsulator. Then his welds were only halfway done leaving large gaps and then it was covered up with body filler. This will most certainly rust from behind because of the air gap. It may look fine in a year, but you can bet it will be rusting until it breaks through again. Watch Fritzee's Fabrication channel here on YT. Check out his "How To Do Automotive Sheet Metal Repair" playlist especially "Butt Welding." This man gives Master Class quality instruction for free here and is a must watch if you want to know how to do it right.
Wow nice bodge! This is why im doing the work i am now to my T4
This is how ALL DIY videos should be - no Stupid intros, no blah blah blah, I love hearing my own voice nonsense. Just straight to the repair video. Thanks for showing the rest how it's done.
What a melon you are
Should be titled "How I did it, but how you shouldn't"
Lol😂
Haha yup
But why
And where Is you´r video Mr Professional?
@@netinfluencer Where are your car metal work videos?
Very poor bodge, this is a structural part of the vehicle, and needs to be fully welded with the correct gauge steel.
Hi there, Thanks for watching. On this part I was repairing the threshold on the car. By all I know it is not a structural part of the car. The structural part of the car is a chassis that I did not repair here. I put a gauge steel what i haved and repaired rust on that part. You can check my video one year later to. Link in description.
MC Tutorials Online have to tell you this is structural part of the car all cars have what is a monoqouqe shell which means the chassis is part of the whole structure including the part you patched up ! It is indeeed structural , the part you patched up is also a jack point on cars and you not using the correct gauge that sill will collapse if someone in future puts a jack under it to say change a tyre
@@iamasmurf1122 you tellum.
@@iamasmurf1122 it's not a structural! Just decorative
@@MCTutorialsOnline the sill is a structual part of a monocoque body. The sill is the chassis part of the car. You could of just used thicker steel, run round the rust with the grinder and welded the patch on top if you wanted to do a cheap job on an old banger.
Excelente y que calibre de lata se utiliza para arreglar el espacio a arreglar gracias
I watched to the end...still waiting to see when the actual repair happens.
What do you mean?
@@aleksihaapasaari he didnt weld it properly, just used a lot of filler. filler not gonna keep your car together and this is a structural part of your car. as i see it would be better to replace the whole rocker panel. he also used too thin metal i think.
Hi, I made some mistakes, I needed to use higher gauge metal and weld it all. But you can check how it's turned out after two years of using car. Anyone who said that this won't work can check it on this link. kzhead.info/sun/dZmkpauSfKSKlWw/bejne.html
@@MCTutorialsOnline No disrespect dude this aint a good repair . If you think it is get the trolley jack out and jack it up on the edge of the sill
@@richardmounfield7822 Hi, You can check lifting up and all other details on this link kzhead.info/sun/dZmkpauSfKSKlWw/bejne.html This is two years after repair.
Вроде и инструменты есть и материалы- но так делать категорически НЕЛЬЗЯ
Можно вам спихнуть лохам
@@vhgd16 это из за тебя ушлепка такие тачки по дорогам ездят, а руки у тебя из жопы растут по всей вероятности из за этого ты только свои обрубки на видео показываеш
Great video! I have a similar issue with my old VW. What kind of metal do you use to this fix?? thanks in advance.
Hi, Thanks for watching. In this repair I used galvanized sheet metal. I used tiny sheet. Use at least 0.8mm thickness.
@@MCTutorialsOnline thanks for that. It is very usefull to me.
Please do not repair an old vw like that. You need to weld all the way round for a start.first you should cut all the rust out in a simple shape like a rectangle make your repair piece slightly bigger than your cut, make it the right shape if it fits on a bend etc, draw round your repair piece over existing hole, trim hole to properly fit the new piece. Then use magnets to hold piece in place. Weld tacks at a time going opposite each time and get the metal in line as you go along. Do not run a bead as the metal will warp and you will blow holes. When finished gently flat the weld with a flapper wheel. The only thing this guy did okish was clean the steel to weld to. It must be very very clean and free of paint and especially sealer anything that can burn will ruin any chance of a proper weld very little or no filler should be needed once finished a car is steel not a plaster cast 😂
@@andyc8826 Hi, Yes he need weld whole part. But I haven't, and repairing is still permanent. I'm using the car in daily needs. You can check it on this link (one year later) kzhead.info/sun/eMl7g7GLkXWwpWg/bejne.html Also you can check my new repair were I welded all around on this link: kzhead.info/sun/h5iImZVojquAooU/bejne.html
Muito bom amigo . Boa tarde. Até próximo vídeo.
Great post! for getting started , Like LE H imorovement addition to this video. Thanks for sharing.
Welding by Stevie Wonder and bodywork and paint by Ray Charles.
Hi, Thanks for watching and for advice.
Took the words right out of my mouth....I guess Ray and Little Stevie did the best they could! They weren't able to attend the "How To Repair Rust" day at trade school, it was a rainy night in Georgia and Ray don't like driving in the rain. So they just stayed home and wrote a song!
Paint job by Helen Keller
Good enough for who it’s for... or as we used to say Close enough for the girls we run with lol
I died
Bardzo dobry przykład jak nie należy wykonać naprawy blacharsko-lakierniczej.
Als ich zum ersten Mal ein Loch am Auto repariert habe, habe ich erst mal ein paar Tutorials geguckt. Das Ergebnis sah sehr viel besser aus und war dtabiler als das im Video gezeigte.
Good job men!!great video!!😉
Не иначе на продажу готовит,Фольгу поставил,да и еще и не проварил плнностью.Мастер иначе не скажешь.Ролик о том как не надо делать.
@@by5182 Тогда какой смысл в такой заплатке?
@@by5182 У него по всему порогу гниль, легче уж порог заменить, а он онанизмом страдает.
Мастер понятия не имеет что такое электрозаклепка. Не знает как что такое гибка кромок. Внутреннее ребро жёсткости не восстановил. Сгниет за год при таком 'антикоре'. Походу не для себя.
He what now?
Nice video content! Excuse me for butting in, I would appreciate your thoughts. Have you ever tried - Tarbbatigan Cars Rehabilitation Tip (do a google search)? It is an awesome one of a kind product for learning how to repair your car the easy way without the normal expense. Ive heard some decent things about it and my friend Sam at last got astronomical results with it.
The title should be How to build a rusting deathtrap 101
Yup. He used super thin metal to fix it and to finish it off he barely welded it at all. In an accident it’ll just crumple to shit in that weak point
Looking to restore a 240sx. I’m expecting rust spots on the frame. Is this a acceptable solution for the future rust issues I’ll have when I receive the car?
This video reminds me of the people that work in my shop
as a guy that work in a car body shop, this hurt to watch
Calm down Billy.
Why, he didn't do it bad enough for you boomer?
@@Anarchy-Is-Liberty aww, did I hurt your feelings? :(
I don't fix cars,but it also pains my eyes
@@denverwood5290 lĺĺ
Your technique was good but the metal you used was too weak. You should've used steel from a junk car. I still liked the video because you did a good job with what you had.
Another tip is use rivets to hold metal with copper pipe backing it grounds out so you dont burn threw when welding
I’m watching this video with a big grin on my face thinking, you’re doing this for a laugh just to see how many comments and views you can get, well it worked.
Wow!!! I’m impressed. Good job!
This was painful to watch. I was a bodyman for 45 years and this was total crap job. You should be ashamed of yourself!
Hahaha hahaha
😂😭
If it's a junk vehicle its fine. Cause a vehicle like this wil be scrap anyways. But I agree
Would you please share how it's done right?
Come on i think he did a great job for his first attemp. You have 40 years of experiance. Know go back in time and remember how mess up your own work was as your first project. SO REMEMBER EVERY EXPERT WAS ONCES A BEGINNER!!!
Nice job, look great.
I just watched it cause the music was soothing 😁
Żywica i szpachla czynią cuda :)
did the best he can with what he had and looks much better than it was before well done
The thing is that it's a structural part of the car, so this "fix" is dangerous as hell, and people like this should not work on cars at al, because when they fix a spot like that, then i don't want to know how they fix other things. So no way that i would let a idiot like this come near my car, let alone that i would let him touch it!🤣
Excelente y la soldadura es eléctrica? Muchas gracias
I am very new at body repair. I am learning on a 72 bug I bought mainly to learn how to redo an old car. What is the clear looking fluid you brushed on and what is the white that that you sprayed on?
Hi, Thanks for watching. Liquid is anti rust protection. White color is color primer.
Wouldn't your life have been made much easier cutting away the rusted metal in straight lines rather than the curves and notches?
Thanks for watching the video. Maybe it would be easier for me to do it that way. I decided on my own way of making it because at that moment I felt it was the easiest and fastest to do. I find that I did a good job of repairing the rust on my car.
It would be harder to shape the patch panel then but its down to personal choice
@@MCTutorialsOnline what kind of welding is that?
Lol, you missed at least a few good inches of metal that isn’t even welded. Any flex or stress placed on that area is going to immediately snap that bondo, then you’ll have moisture and junk going inside of your rocker panel.
Hi, You can check how it's turned out after two years in this link kzhead.info/sun/dZmkpauSfKSKlWw/bejne.html Then you can decide is this repair good or not.
Тонкая работа!)
Amazing Job !!!!!
I am so glad to see, the old addage, No job is to small to bodge. Is still alive and kicking..
Да ,было дело, в мытищах такие стояли на продаже и не только.
"хороший ремонт", мне больше музыка понравилась.🤭🤗
great job man 👌
Hi, Thanks for watching and supporting me in my work!
I want to do this to my truck, but I don’t know the proper tools. What tools did you use and brands?
The only thing I have to complain about was the music, other than that..don't listen to these comments. This was a cheap repair, that got the job done. It in no way interferes with the structural integrity or safety of the vehicle..so there is no 'danger' like some are saying. The only thing that could happen in the future is the piece of metal possibly falling off..but even then..not really a life threatening danger. I cant stand when people sit there and critique others in these rude manors, and they probably have some shit eating grin while they are doing it..I mean Were they there to fix it? were they there to buy the supplies? Do they want to send you the proper supplies or instructions to do it the way they want? The piece was so badly rusted, you really did not have a lot of options, but to remove the metal entirely like you did. I mean there was even people bitching about the way you grind the metal off..I mean are you kidding me??? I mean what do you all think he was going to do differently? its so fucking petty. These people do the job once, buy the most expensive products to fix the issue..then they think they have some kind of bragging right to go around and tell people how they should do it..because they did it that way and spent more money then they really needed to. Not to mention, this is all a professional shop is going to do anyway, granted yeah, they will take their time and make it look like its brand new and spotless..but your going to be out an extra $300-$400 for a repair on a piece of the body..that no one is going to see anyway. I have seen this shit first hand my self, case and point. I am out mowing the lawn one day, the new neighbor walks over..and tells me I should mow in straighter lines...get the fuck out of here ya old fart. You fixed/repaired the damage to the best your ability with the tools you had at hand, and what you could afford. There is nothing wrong with that, and frankly that is a major lesson and aspect of life today that is forgotten and spit on. Most important of all though, you were not boasting about any of it or bragging saying "oh you have to do it like this" So dont listen or take any of the shit people are saying you did a good job(excuse my FOUL language).
hi, i'm extremely grateful you watched my video. I am especially grateful for such a detailed comment in which you described everything that needs to be described. my repair was cheap and I needed it fast. I saved over $ 300 on this repair and the repair is still permanent. I hope the others see what you saw.
Yeah man, good job making this video, my repair will never be perfect either but neither is my car.
You obviously don't know how structural rigidity works in a car & how vital the rockers are in the event of a crash. This is NOT "how 99.9% of shops would do it" at all. If this guy (or anyone he sells it to) are unlucky enough to crash this car, they will undoubtedly sustain more injuries than they would have done of it had been repaired properly. This is not petty, & this is why so many people are commenting about it. He had the tools to fix it to a reasonable standard, but he didn't.
@@MrPabsUk I think you don't know what driving a shitbox is like. I've driven around in shit with rockers completely missing and holes in the floor. I scrap them afterwards. Most shitboxes hit the crusher after they get to this stage, a poorly patched rust hole is likely the least of this cars problems. At any rate I've done safeties on cars that I have failed because huge hunks of the frame are missing (Toyota trucks or GM A bodies have frame issues) I don't know what this car is but it's obviously a unibody anyway. Unibody cars are so shit that windshield and back glass give the unit structural rigidity and if you remove them and take the car over a bump or two the entire car will bend. Literally glass and glue is used for structural integrity. Anyways have a good time on the Bus/Train.
@@ryedogg6767 I`ve owned over 200 cars in the last 3 plus decades & a good number of those were purchased as $100-500 shitboxes with failed tests &/or crash damaged, I`m a qualified mechanic & also do bodywork, including welding & I`ve done full blown, ground up resto`s. I`m not sure what your point is supposed to be about unibody construction, I mean, how many separate chassis cars are there these days? If anything your proving my point about the need for uncompromised structure in the rockers if you want to maintain any degree of structural rigidity, yet at the same time your giving this guy a pat on the back for a good job? I reckon I`d be able to kick that rocker straight through in under 2 minutes.. You wanna die a slow death, bleeding out from your crushed legs in a crash that wouldn't have been serious if the cars structure hadn't been compromised by poor quality repairs, then good for you, enjoy. And what percentage of people do these shit 3rd world repairs, then sell the the things to unsuspecting people? Oh, and I`ve not been on a bus or train since 1991. Have a good day..
Looks like a fine repair on an old car. It'll help keep the rust out for a few more years.
Not because he not treat,scrap or remove completely the rust around the reparation.🤷♂️🤦♂️
Hi, You can check how it's turned out after two years in this link kzhead.info/sun/dZmkpauSfKSKlWw/bejne.html Than you can decide is this repair good or not.
@@AngelHernandez-ls5wr tengok la video dia..ketawa la awak..panas saja awak..hantu
Nice job,respect 👍
Hi, Thanks for watching and supporting me in my work!
That is a great lesson in not how to do it !!!
If Alfred Hitchcok would have been a sheet metal fabricator!
its a great video - he took out hte rust and replaced it with metal and grinded it and expoxied it i dont know why there are so many haters
Hi, Thanks for watching and supporting me. I have done some mistakes. I haven't weld all around. But I didn't have that in my plans, I wanted to have cheap and fast repair.
This man is the “Bruce Lee” with a Sanding Block!
"A grinder and paint will make you the welder you ain't"- my welding instructor
Надо было пеной монтажной запенить а потом зашпаклевать, эффект был бы тот же
Для тебя
Что то говно также как и пена
Как мой брат купил 2105 и через год узнал что пороги запенены
Forget everything you've seen
Did good for a back yard diy, but you made so much extra work for yourself.
Beauty is in the eyes of the beholder and what they believe will fulfill the job. When I was younger working in a body shop I was a painter and when the body shop would send work over to the paint shop we would look who’s name was on the body shop ticket and we knew who the butcher were. We used to yell out “make way for the butcher” the days of making fun on one’s work was our enjoyment again beauty is in the eye of the beholder, don’t be a shallow, Hal
Awesome job for DIY. Really hard to see uneven pattern specially when your working in the bottom. But i saw alot but ayy looks pretty good tho. Good job.
We the ones who live in the USA can just order a whole new rocker panel and avoid all the other complications.... but not all of us live the US and resources aren't handy to everyone or to most ppl in western countries, i'd give him a 8 out if ten for this job, the guy is working around what he has and he is making it work, he could have had welded the whole thing given that he was already using a thinner sheet of metal, but lets stop bashing on his work because im pretty sure we'd all do the same if that was all we had to work with.
Iiok
Oooooooooooooooooooooooooooooooooooooooooooooooopooooooooooooool
в том месте нужна жесткость, так как туда подставляют домкрат, и поэтому там нужна нормальная заплатка и проваривать ее надо по всей площади
May be 2 Out of 10 and I'm being nice yust for been brave to show it on you tube 😀
Buen tutorial 👍
Druciarstwo przez wielkie "D"
To jakiś dramat....😔
Rzeźba w gównie, totalny bezsens 🤯
I cyk do sprzedania, a za rok to samo 🙂 cały próg wstawiać, a nie jakieś łatanie i kilo zaprawy
kończy jeden koniec a na drugim wszystko w gruzie, co on łata???
I'm glad I found a video like this because when I buy my first vehicle its going to be a dodge truck or SUV and you already know how they rust out so when I do rust repairs I'll know exactly how to do it so thank you for posting it.
Just know there was no reason to use a grind wheel, just cut a square and tac weld it in place, the rest follows.
Thank you that helped me
Many critique the man’s skill not taking the vehicles condition into consideration. The repair is only as good as the car and its purpose.
I should have welded just a little more but it's not my car so as long as the owner is happy it's job done 👍
Hey fuck it!! I use balsawood and super glue!! Much easier to sand!!
Can’t see it from my house. Good enough for government work.
Bonjour quel tole utiliser vous en remplacement ?