Do you have an old aluminum boat with nasty, flaking paint that has seen better days? In this video, we show you how easy and inexpensive it is to transform an ugly aluminum boat into something you'll be proud to use on the water. And you can do it all without fancy tools or expensive marine paints. Watch to find out how!
Need more help painting your aluminum boat? You can find a step by step guide with a complete materials list on our blog here: www.fishingduo.com/how-to-eas...
Or check out our fishing blog for even more helpful fishing content: www.fishingduo.com
Essential materials we used:
Wire Wheel: amzn.to/3TVy6q3
Corded Electric Drill: amzn.to/49BlzOd
Paint Scraper: amzn.to/4aRn1gl
Citristrip Gel: amzn.to/3UhOwdO
Rust-Oleum Comfort Grip: amzn.to/3UoZf6h
Rust-Oleum Hammered Paint: amzn.to/3vWtwj5
Krylon Colormaxx: amzn.to/3Q1SPr4
Sanding Sponges: amzn.to/4auAvyJ
Frog Tape: amzn.to/4cVuLQw
Masking Paper: amzn.to/3PVtfE3
Plastic Drop Cloths: amzn.to/4aIGMqE
Respirator Mask: amzn.to/3Jc7dZY
Low Oder Mineral Spirits: amzn.to/3VWbkRf
Paint Brushes: amzn.to/3TSXwog
*As an Amazon Associate, we at FishingDuo earn a commission from qualifying purchases made through product links. However, we only link to products we use and can honestly recommend. Purchasing products through our links helps to support this channel so we can continue to produce even more helpful fishing content. Thank you!
I just bought an old 12’ Sears fishing boat. This is exactly what I needed to watch. Perfect timing. Thank you! 🙏🏻
Great video! I can’t wait to redo my old aluminum boat now! Thanks
This was a great job done to an old aluminum boat. Given today prices this is the way to go!!!
wow really great job . i like the idear of stripping the paint off ,great information thank you for shairing
I've owned several aluminum boats in my lifetime and I even camouflaged a few that I hunted out of. I never repainted any of the others, because the factory paint was still in good condition. My last boat, a 14 foot Proline V-bottom, has no paint at all. This is the way it came from the factory and since I no longer hunt, I like it. When I first bought it (used) I replaced the wooden seat tops and they now have side by side pine 2X10's left natural and painted with clear a spar urethane. I just buffed the aluminum a little to make it shine and it looks great. After looking at many boats since then, I've come to realize that I'm the only person on my lake that has an unpainted aluminum boat!
Good video! I already did my old Lund, but I followed the same basic process as you showed. I like the Krylon and Rustoleum Farm and Implement paints; very affordable, easily available, and very durable. For small aluminum boats, a decent looking paint job doesn't require paint that costs $120 per gallon.
Nice video. I have restored the inside of my boat and ready for the outside. This video will help me tremendously. Big thanks!
A couple of cans of Rust-Oleum Bed Liner sprayed on the floor now wouldn't hurt.
Thanks for sharing, doing the same thing to a 1966 mirrocraft 14ft aluminum boat right now.
I have the same exact boat. Mine is a 12ft. Nice paint job!
I'd have used a pressure washer before the stripper and to remove the stripper after it did it's work. Nice video!
This is pretty much the same method I used on my boat. Mine is a 16' and I painted the inside a matte gray and the outside a semi-gloss red. I also chose to leave the bottom unpainted as that was where the most wear would be. It's been good to go with no scratches since 2021.
Great tutorial! Thank you for the video.
Good tips. 👍
Orange strip is great stuff for an Aluminum boat. Gluvit or Total Boat aluminum epoxy will seal up the bottom seams and rivets. Just in case. Primer, paint, done. Never, ever, ever use Flex-seal on your boat.
I used flex tape for a boat plug replacement… 4 years later still holds
Always hook a safety chain to your boat motor.
Great video. What needs to be done prior to check for leaks in the rivets and welds?
m.kzhead.info/sun/pK-Kkc9whnaXdJ8/bejne.html
If you sand the bottom to bare alluminum dont you need to protect it with something? Im working on a similar project and was hesitant to work on the hull .
There are coatings you can apply to delay oxidation. Oxidation will definitely dull the shine so if that is important to you then you should coat it. However, I find it's less expensive on small boats to just take a fine grit sand paper to it ever year or two to restore the shine. But if you don't, oxidation won't reduce the integrity of the hulls strength and it still looks pretty good after many years. Thanks for watching!
Would Rhino Liner work on the inside of the boat? Might get good traction for getting in and out.
My friend bought a boat with that stuff sprayed inside the boat whoever sprayed it did not prep the surface correctly and it started to peel in areas something to think about
Just wondering if perhaps I should consider getting a can of Gluvit for the rivets and seams. Yes it will definitely increase the cost of the project as Gluvit is not cheap. 😏
Definitely worth considering since rivets on an old boat often leak.
I've used it on my old starcraft that I refurbished...bone dry in the boat, and that's with some rivets replaced with stainless bolts and nylon washers... its runny stuff, but works good...I applied to all the seams too for extra leak protection, inside and out.
I highly recommend Gluvit! It’s expensive but it works.
Why not just hit the boat with a pressure washer after the gel eroded the paint?
Honest question. Not sure it would be enough, but in think it would eliminate a lot of the manual scraping
I think that could work. But the amount of paint material that comes off a boat is more than you might think. I wanted to contain it and throw it in the garbage. if you have an area you don't mind making a big mess, go for it. It would save some time for sure. I also don't have a pressure washer, hence the scraping. Thanks for watching!
Should of hammered SOME dents out.
Can't argue with that. I was afraid to do more harm than good though. Thanks for watching!
Do not use a wire wheel on aluminum! It will cause it to corrode! Never ever do that!
USE A Stainless Brush Only
Yep. Dissimilar metal corrosion.
Hmm, I haven't had a problem.
Even if painting over it?
@@emptyjar02 Yes your never want to use carbon steel on Aluminum because of Galvanic Corrosion especially on aluminum that will see moisture.
Stainless steel will corrode aluminum.
With all the work people put into painting and then paint it RED the worst color as it fades in short period of time now they end with a crappie red