How to make 5000w 250v Free Electric Generator at Home

I built a similar apparatus, but instead of microwave transformers and wires, I used an old shoe lace wrapped around a frozen banana cut in half. Use ripe banana for the negative coil, and fresh banana for the positive. The 9v battery and driving motor are not necessary if you use a stack of marshmellows on a wooden shaft as the armature. The sugar molecules cause continuous rotation of the marshmellows, but an initial spin by hand is required to get it started. Don't let it run too long, or it is difficult to stop the shaft rotating.

I think this generator could work but it would create around 5 or 6 V and it will give you very little current (i think around 15 mA) because of impedance of winding, not closed magnetic circuit and large distance between winding and rotor. This generator will never create 5 kW, maximum power from 9 V battery is around 11 W but motor this guy used don't take 11 W ( i got similar one and it takes 500mA from 9V battery so 0.5 A * 9 V = 4.5 W. Efficiency of DC motors is around 80%. 4.5 W * 0.8 = 3.6 W. So 3.6 W translates into mechanical energy. So if you use the same motor also as a generator it would create 3.6 W * 0.8 = 2.88 W and even less because of impedance of winding. This guy build his own generator that is much less efficient so power losses will be huge.

5000 W ? No. 0.005 W, Yes. A very efficient way to waste energy.

Be careful of the wire coming up through the center of the table which powers the thing.

The extra thick base keeps the massive amount of current and voltage generated by the device from tearing itself apart. Great engineering.

El cálculo de corriente @ 5000W y 250V es 20A. El calibre del cable de cobre necesario es 12. Se puede ver que el calibre usado en el proyecto no se acerca a ese valor. Puede deducirse que no pasarían 20A por el cable usado sin dañarlo.

its amazing , so many amps from a thin wire and if i am not wrong you didnt remove the insulation of turning wire before connection .

Interesting solution !!! from where do you get the magnets?

Another genius. Tell us, O Genius, how does a 9 volt battery that can supply about 1-watt of power to turn the motor produce 5 kW of power? When you've come up with the BS to explain that, maybe you'll move on to make a 10 Megaton thermo-nuclear device in an egg cup.

Please can you show us some voltage, amps reading on your nxt project its really exciting watching thanks buddy

Where did you get all the components? A list of components would also be appreciated, thanks in advance

Lo he probado con la lavadora y funciona....gracias Apu . Tienes pensado vender este artilugio en el badulaque?

There is no doubt, this flimsy wire makes a lot more than 5 KW. The rotation speed is not even affected of output power. I am convinced you can also power a whole city with your 9 V Battery for about half a day. Amazing discovery!

So how long will that last before you flatten the battery?

The round magnet is placed in alternate N and S pole?

Although I like your videos, I do wish you'd include V & A input & output readings. Also, the wire gauges & # of turns on your coils.

buen video muy bonito pero amigo por que no levanta la tabla estando todo encendido por que no termino de creer esa potencia con esas bobinas tan insignificantes pero el video y lo fisico muy bonito lo felicito.

Love your work. could you put links to where you get your parts from? trying to learn as much as possible. keep up the good work!

i like the design , but can you show me what under the table and the voltage and amp ?

At least he didn't hook up the output of the generator back to the input of the electric motor, claiming "perpetual motion"

5000 watts 😂🤣😂🤣😂 Run 3000watt motors Waste video, Waste my time.

Great job. Love the design and simplicity. You can use microwave transformers as the coils so you don’t have to wrap your own. I would love to see the voltage and amps output it as well.

Aren't you afraid to bust your 9v battery by soldering it perm. on your circuit ? once it started, it should be removed ?

Buen video magufo... si fuese verdad: resistirian esos conductores? giro la tabla base pero nunca la levantó.

What material are you using in the beginning? Is it paper or plastic?

Where can I find 9v batteries that can supply over 500 amps? (9v @500 amps = 4500 watts)

Silly question I'm sure, but what if you plug in the 9volt into the PowerBar and gave the spindle a manual push at the beginning, wouldn't that create enough energy to push the little motor?

Been trying to learn generators since I been using one. Used one 3000w till it blew up. Got a new one, don't know too much about why it blew up, I kept the fluids good, I guess it was just too old? Too much use? How do I make my own that ain't going to blow up lmao

Not to mention 20+ gauge wire can't support that much current.

To those who are wondering, this is not perpetual energy. No such thing. Bubble popped, I know. 😂

Thank you bro main ek barr jarur try karunga yha farmula ,

good Idea , you just modify the mechanical motor by turbine rotation (water turbine)

Do you know what is the meaning of 5000 watt ? Idea might be nice but 5000 value over

В столе дыра, через неё в трехрозеточный пилот заведен сетевой провод, именно поэтому от стола он эту хрень ни разу не приподнял, а лиши слегка сдвигал и вращал вокруг оси. Провода из пилота -бутафория.

How did you hide the mains connection? As 001 002 asked... What's under the board?

You're a serious artist as you managed to hide access to electricity somewhere under the board. This system cannot work because the motor hasn`t slowed down a bit under large curent

If your video is not informative and you hide the number of wire and number of turns, boban size, then your video is a joke with seekers and a waste of time. Many people here watching videos to learn a proper way to make something but this video is a waste of time for them because they don't know the wire number, number of turns and the size of boban, then there is no benefit for people and they are wasting time on your video.

5W...maybe.. :))) If U looking carefully, wire is conected to coil, AND under conectors..to whole in the desk, directly to 220Volt's..

Is it possible to discharge battery while charging it at the same time?

which better.. save cost ...long life use....dynamo magnet battere or inverter batere...

It would be cool if you can connect the power source of the motor to the outlet and pull the masking tape hard to start the rotor and let it perpetually turn so it would be self powering. Too bad the magnets are to strong and will just seize the movement.

hold up the system board! tow power lines under the system is calling "fake!"

WHAT ARE THOSE W SHAPE BLACK THINGS OR ANY OF YOUR TOOLS USED CALLED?

Exelente maestro. Simple y cencillo. Me imagino que con más bobinas y revolución más energía y potencia.

Great channel. But it would be great if you listed all the parts used and even somme of the technical information. Could you tell us what are the "E" part are? They look familiar but just can't think what they are.

How do you know how many turns the coil needs?

You use electrical energy to generate electrical energy What a great invention.... At least you could have made the generator be moved by water from the tap....

hi, is it possible to have a specs list? We didn't get much from the video. Thanks anyway for your peculiar contribution.

How many turns you made in the coil?

The first quarter of the year was all about survival with many achievements not met but you have to be ready for second quarter and it begins right now by making a move to achieve your goals…If you have been saving and it’s not really getting you to were you want to be, then invest that money today for a better life tomorrow. If you can’t fly, run, if you can’t run walk, if you can’t walk crawl but just try and move to achieving your goals.

La plus grande découverte de tous les temps, il lui faut le prix Nobel.

THE coils you wound are just first class. A nice video would be to show how you wound them three technology. Just an idea Sir. How long does the 9 volts battery last with three bulbs connected to the unit ???

Now I have a question.. Couldn't you also plug in a battery charging device so that you always have full batteries... Wouldn't that be great, wouldn't it?

Parts list please. i would like to make it, but i don't know exactly which parts to use.

How many watts does it take to pick up a few bulbs? At the very least, it makes sense to measure the voltage with a multimeter and test the power

Super design, absolutely I am sure that it is minimum 5.000 W maybe 10.000 W or more. Now you should start 3 or more big size of these to get minimum 1 MW. Thank you very much for share your knowledge.

Если смотреть провода на катушке они потянут максимум 250ватт ито греться будут

See the motor runs with constant speed even you have loaded 3 different things

Why don't you put a transformator 220 to 9v on the plug to replace the 9v battery after it started to produce 220v ? Like this you can close ce loop ?

Why design it so that you're going through a mechanical coupling between the generator and the motor that turns it? Why not put the windings in the same assembly and use inductive coupling? That way you can minimize losses and make the scam look even more amazing! 😃

этот чувак в курсе, что такое 5 кВт/ч? ))) пусть подключит 4 электро-чайника ;-)

You can't power electromagnetic coils without the "electro" part so this is fake.

What is name of that gear used and fixed neodymium magnets in it

I think I figured this one out. This very powerful 9v battery is not an alkaline battery, it is made from unobtainium, which will theoretically last forever.

Connect the stove and cook the eggs

To whom it may concern. Over Unity Electric Generator Design: By ☯AMA☯ Segment 1: 1 motor with hollowed bar connected to it standing vertically. Circular disc connected to bar that has magnets embedded in it's top side all around, surrounded in high permeability material to focus magnets outward pushing force in an upwards direction from top of disc. Segment 2: Hollowed out cylindrical Bar of material horizontally positioned. donut shaped platter that's flattened on all sides instead of rounded, all around the flat edge of this platter, from the center is a ravine in the center so structure looks more like 2 donut shaped platters flattened on all sides & sandwiched together against a smaller donut shaped platter that's flattened not rounded & between them both. Square openings are located all around the outside of platters edge on both sides & goes all the way through material. In these openings rectangular magnets surrounded in high permeability casings are slid into place all around platter in a matching pattern on both sides. N facing in then S facing in. Connect these securely all along the length of the horizontally positioned bar except at far ends and center. At both ends of horizontally positioned bar securely connect a ring of material that can be magnetically repelled (This will allow bar to spin when apart of completed construct) Build a hollow ring structure that has ring of magnetic repulsion around its inner ring that will be able to fit around main horizontally positioned bar and keep it from touching anything on account of the bar sitting on its magnetic field inside the ring. The ring structure has a rectangular bar protruding from it's outer edge & has small square platform on end of it that will allow it to be screwed in to another structure. Make 3 of these ring structures & position them (approx) over both ends of horizontally positioned bar & around it's center. Build hollowed out rectangular encasement that is separated into 2 pieces that can be placed on top of each other and screwed together. This encasement will fit over horizontal bar & everything that is immediately around this bar. Encasement needs areas all along it's top side that has screw openings that all structures inside that need to be fastened down will be able to screw into. (Best if encasement is transparent) Encasement has round opening at both ends so when in place horizontally positioned bar with round magnetically repel-able disc attached to it are sticking out. Build hollowed out ring structure (flattened not rounded) that has a hollowed out rectangular bar that protrudes from top and bottom of ring and has square platform at end of each that will be able to screw into inside of encasement on top and bottom. Ring structure should be able to separate into 4 halves (from middle separating top & bottom & from side to side on each) that sit on top of each other & side by side perfectly connected when encasement is closed. Hollowed out aspect of ring structure & it's protruding hollowed out bar that's connected to it is for conductive wiring to be placed so that the copper coil constructs not mentioned yet will be able to plug into this ring structure and the current can be diverted up through the hollowed out area to a point where another device can plug into it. On bottom of hollowed out ring structure there are openings where copper coil constructs can be plugged into. Build wide but small ring with ravine around its outer edge in center (kinda would look like the round metal piece you would see in a pulley system but not angled in) of structure (flat not rounded & not hollow in center). Copper coil will be coiled around this. Build hollowed out rectangular structure the length of the width of the wide small ring structure. Build a plug system within it so at the center of the rectangular structure it has proper electrical plug poking out that will be able to plug into bottom side of larger ring structure that is designed to divert current. At both ends of small rectangular plug system there should be flat rectangular legs hanging down so that you can fit it perfectly over center of small wide ring structure that has copper coil wound around it & screw openings at bottom of these flat rectangular legs so they can be screwed together. Ends of the copper coil are fed up into the plug securely. With wiring in place screw top halves of ring structure together still separate from bottom halves. Then with wiring in place screw bottom halves of ring structure together. Now screw the already connected top halves to the inner top encasement structure & same for bottom halves. Two main encasement structures still disconnected at this point. (Fine point... there are as many of these ring structures with copper coil constructs plugged into them as there are the magnetic disc constructs lined up across the length of the horizontal bar) This is because they are all to be lined up. Now with everything ready carefully lift up the Horizontal bar with the magnetic disc setup securely attached to it. At this point the magnetically repelling rings that are at far ends and center of bar should be hanging freely. Carefully position this whole thing in the bottom encasement so the copper coils are positioned perfectly in the ravine of the magnetic disc area connected to bar. Line the free hanging magnetic rings that have rectangle bars and square platforms up with the inner bottom of encasement and screw them in. At this point the horizontal bar is sitting on the magnetic fields in the rings and is securely in place connected to bottom encasement. Now pick up the top of encasement and carefully line it up the same but on top & then screw the top encasement to the bottom encasement. If lined up properly you will see that when the horizontally positioned bar is made to spin, the magnetic fields will interact with the coils that are perpendicular to the magnetic field lines and since the copper coils are positioned to hang withing the ravine, the magnets on both sides will magnify the effect to achieve greater results & since the magnets on both sides are set up N then S all the way around it will end up being AC current. At this point you may be wondering how will this ever equate to over unity? well we are about to get to the part that makes that possible. Build cylindrical structure (like a donut but flat not rounded on all sides but still hollow in center like a donut). The cylindrical structure is built in 2 parts. Top part & bottom part. Bottom half has a ridge close to bottom center area that circles around further into the center but not all the way in. On top of this ridge is a flat ring of high permeability (magnetic field shielding) material that has small openings that will allow magnetic fields through specific locations. The top flat side of the 1st part has rectangular grooves cut into it that go almost the entire distance from outside of cylindrical structure to hollowed out center. At both the outer edge and inner edge it instead cuts down sharply & narrowly at just over the width of the horizontal bar. This way when the horizontal bar in it's encasement is sitting in this spot the case fits down in and bar slides down in with a little extra space but the encasement can't shift forwards & backwards. The top half of cylindrical structure has same groove but no extended ridge going further towards center. Fill the rest of the rectangular grooves with duplicates of the electric generator construct. Now carefully position top of cylindrical structure in place and screw it to bottom section. Now position the motor segment with the vertical bar that has discs on it in center of cylindrical construct so the disc is lined up perfectly underneath the inner ridge that has the flat ring of high permeability material fastened to it. Now you can duplicate this whole setup and stack it for more electrical output. (The only thing that would need to be duplicated with the motor & vertical bar setup is for you to add another disc with magnets embedded in it, higher up on the vertical bar you are already using). When you turn motor on the discs will spin and the magnetic fields on them will only interact with the discs on the horizontally positioned bars when the magnetic field lines go through the small openings in the high permeability material. Since those openings are lined up with the edge of the discs connected to the horizontally positioned bars, it will force them to spin, effectively generating lots of electrical current. Just make sure to let enough of that current pump energy into the 1 motor you are using to run things, and the rest of the electric current is over unity. If you are still wondering how this could end up being over unity, the answer is simple. The device exploits magnetic field effects connected to the vertically positioned bar connected to the motor to have them do all the extra work so the motor does not have to. And since the magnets are exerting there force upwards while the bar spins around sideways, the motor won't be getting a detrimental amount of push back. This design invented by ☯AMA☯

Ask how many turns are per transformer or coil and if I want 9000W how many turns would that be?Then I have more curiosities like how much power does the homemade generator have? can sustain a house?

What you have here is a mechanical inverter. Inefficient but it would be a sine wave. You need something like a golf cart battery to power this.

Всё правильно, но батарейка и движок работают отдельно и насколько хватит энергии батарейки?

I especially liked the part where you added a battery to your free energy device..

1 unit We can use for 9 volt adopter to run the motor

Because such a small invention has such a large outlet, it could have a built-in battery

Возьми прибор и докажи что там именно это

I'm laughing hysterically as I'm watching this. Thanks for the laugh...

What brand is that battery? I want to buy a 5000W 9V battery!

Human evolution peaked some 10,000 years back. We are in the diminishing phase now.

pick it up and lets see where the "other" wires are....

It's not about physics, it's about believe.😊

good but if you can provide us the details of parts and links if possible... thanks

Great idea of hiding main supply, made a hole in switch board through wooden plate and passed under the table smartly you selected the board which opens from upper side.

NOT FREE ENERGY! You have a BATTERY connected which is supplying the POWER to run this device! THAT is not "free."

Obviously this machine works. No need to show a further back view or the table or under it. That would only prove that there’s no tampering going on! Why would you prove that if it’s working fine!!!

if you removes the batery, while the machine is processing ? did you tried ?

How to built it? My home is beside the river.. i need to use it with water flow energy to produce electrycity.. how can the small turbine like that can produce electric?

Olhando assim, realmente seria maravilhoso se fosse verdade, merece um like pelo trabalho que deu para enrolar o fio, mas tambem merece um deslike por tentar enrolar muita gente que acredita que isso funciona, pois o maximo que conseguiria era acender uns leds...

Excelente trabalho ,bonito e limpo valeu.

SO : HOW LONG THIS 9 VOLT BATTERY LAST TO KEEP IT WORKING ?????? CAN THIS DEVICE OPERATE A WASHING MACHINE AND A FRIDGE AND AIRCONDITION??

Só acredito que funciona se ele parar o gerador com a mão!...E sem tirar as lâmpadas das tomadas!...E se na hora que ele parar o gerador com a mão!!...se as lâmpadas apagarem e a hora que ele tirar a mão do rotor do gerador!...E as lâmpadas acenderem denovo daí eu acredito!....👍

i think there is a magnetic field under table from a primary coil transformer

He has a pair of wires coming up to the power board from below to power the lights - that's all people. The secret wires pass through a hole in the table.

Super. Great thought. Good work.

Great works. Thanks a lot. Where can I buy the materials used? Kindly share links to each material.

Followed your design and I now power my 2700 sq ft home and my neighbors. Simply amazing.

Две лампочки это не есть доказательство 500 ватт

Mümkün değil o pil ile motoru döndürmek yük ile ortalama 500 mili amp. harcar ve o 2 adet bobinden çıkan güç belki 10 watt gibi olur...

What is the copper wire gage and turns.

FAKE

Ridiculous nonsense!

Can this generate atleast 500watts?

Can you create a diy generator that can run an ref. An a tv..by using a electicfan motor that turn the generator??..