Metal Gel Repair Metal Gel Repair add appeared on Facebook. Comethry
Пікірлер
Hi Jim, I think first your mixing was a bit short , and as 2 component system, a proper mixing is key. Your poor mixing may cause reduced properties of that glue. I use this kind of glue (Tertell ) and after drying , this looks like stone hard! Thus, regarding your handle, it's best to apply the glue both sides of the cracked handle, which should harden far more ( but at least thicker coat than you did )... Hope the best
@jean-francoisburgy444 Жыл бұрын
Thanks for the info. Probably didn't mix it well enough and on the handle good idea putting on both sides. Yes probably didn't have enough.
@JimMcLaren1950 Жыл бұрын
Wire cutters I put a paperclip through the hole then glued it all. Later filed off the extra and it held.
@grandpabill1959 Жыл бұрын
Going to try JB Weld . Good idea using the paper clip. Thank You.
@JimMcLaren1950 Жыл бұрын
Great video Sir !! I also seen this on Facebook but thought I would come onto KZhead and check if there were any reviews before I pulled the pin on this , and I'm glad I did !! Thank you for sharing your experience with this Poor quality glue !! You saved me some money and gained a Sub !!Take care !!!
@erikkekkonen2941 Жыл бұрын
Your welcome. So many ads on Facebook they all look god in the videos but lots are not worth buying. Happy I saved you money. Plus thanks very much for subscribing. I have other products from Facebook coming up for review . ( Chubby Cable )..
@JimMcLaren1950 Жыл бұрын
Will it work on wood?
@jameswells97495 ай бұрын
Thanks for the great video, I have a broken part of my exhaust car, can I use this glue to stick a piece of metal to it for a long time? (I want to use this glue instead of welding)
@parvariramin Жыл бұрын
If I was to try anything I would use JB weld. I did use JB Weld on a wood stove so that the latch would hold in place. I am not sure that it would work on your muffler but JB Weld works a lot better than the stuff showing in the video and JB weld comes in a larger size the tubes in the video are small and would take a lot more to attempt the job.
@JimMcLaren1950 Жыл бұрын
JBWELD - enough said.
@kevinisawakeАй бұрын
JB Weld works good.
@JimMcLaren1950Ай бұрын
Thanks for the review! It looks like this glue is made for leaks only..
@chingonmex24888 ай бұрын
Your welcome.
@JimMcLaren19508 ай бұрын
Is it use to aluminium to aluminium how long its bonding ?
@sharppen95195 ай бұрын
Not even 4 minutes in and he is going to fail! The piece on the wire cutter is supposed to pivot! If you "weld" it in, it will not work!
@oldschooldiy324011 ай бұрын
Yeh I know this stuff it's been around a long time now, many years, it used to be liquid metal it was called you could buy it in big tubes, it never worked then and it obviously still doesn't work. The idea is good but the product just doesn't work. Who wouldn't like to use a glue that actually worked for what it was made for, but such things are very hard to find. That plastic break, you might have more success using super glue with Styrofoam, there's a guy on youtube been doing this stuff, not tried it yet but I know the super glue and baking soda thing works pretty good. I suspect the super glue with the Styrofoam would work as it's a type of plastic and super glue works well on plastic, also it melts that foam making it a hard substance. But the metal part you might be better off trying to weld that back together or file it down and use a plate and attach the spring thing to the plate, if you still have the parts that is.
@flitsies11 ай бұрын
Does this work on plastic / PVC pipes?
@be236 Жыл бұрын
It says it does.
@JimMcLaren1950 Жыл бұрын
JB Weld failed the same way though
@Schroeder9999 Жыл бұрын
Hi, is this glue good for exhaust? 🤔
@Dendrotera1 Жыл бұрын
The tubes have very little glue in them. I would try JB Weld.
@JimMcLaren1950 Жыл бұрын
No, its stands only for 200 celsius.
@reioXyhiАй бұрын
Basically, the Chinese sold you snake oil...
@alpachino4684 ай бұрын
lol
@JimMcLaren19504 ай бұрын
Ohhh you didnt mix it enogh. Thats important.
@reioXyhiАй бұрын
Thanks Do you go by color ir just mix it longer.
@JimMcLaren1950Ай бұрын
@@JimMcLaren1950 the same a+b glue buyed from Aliexpress says mix very carefully, i mix it maybe 3 times lomger time than in video.. I have never failed and I'm surprised every time how really good this glue I've never tested the heat resistance, promised 200 celsius but I will some day in my empiric research😄
@reioXyhiАй бұрын
@@reioXyhi Thanks for posting.
@JimMcLaren1950Ай бұрын
السلام عليكم ورحمة الله وبركاته فين كيتباع هاد المنتوج
@saidberjali7075 Жыл бұрын
في ali express
@sulimanalghaithi9342 Жыл бұрын
Plase I wan oder
@syedsheikhhamidalattas36977 ай бұрын
There is no web page to order from. Looks like they discontinued.
@JimMcLaren19507 ай бұрын
Chinese junk! What about JB Weld?
@woodsmanforlife1677 Жыл бұрын
Tried JB Weld but not for Plastic or pliers.
@JimMcLaren1950 Жыл бұрын
@@JimMcLaren1950 it kinda does work for plastic and metal.
@Nathan-lt6bw Жыл бұрын
@@Nathan-lt6bw JB weld did work for other metal things. I used it on a stove where the latch wasnt catching. Built it up so the latch would hold. In place.
@JimMcLaren1950 Жыл бұрын
Chinese goods are good at advertising only
@troyaikman1234 Жыл бұрын
Exactly , it doesn't work as shown in their videos.
Hi Jim, I think first your mixing was a bit short , and as 2 component system, a proper mixing is key. Your poor mixing may cause reduced properties of that glue. I use this kind of glue (Tertell ) and after drying , this looks like stone hard! Thus, regarding your handle, it's best to apply the glue both sides of the cracked handle, which should harden far more ( but at least thicker coat than you did )... Hope the best
Thanks for the info. Probably didn't mix it well enough and on the handle good idea putting on both sides. Yes probably didn't have enough.
Wire cutters I put a paperclip through the hole then glued it all. Later filed off the extra and it held.
Going to try JB Weld . Good idea using the paper clip. Thank You.
Great video Sir !! I also seen this on Facebook but thought I would come onto KZhead and check if there were any reviews before I pulled the pin on this , and I'm glad I did !! Thank you for sharing your experience with this Poor quality glue !! You saved me some money and gained a Sub !!Take care !!!
Your welcome. So many ads on Facebook they all look god in the videos but lots are not worth buying. Happy I saved you money. Plus thanks very much for subscribing. I have other products from Facebook coming up for review . ( Chubby Cable )..
Will it work on wood?
Thanks for the great video, I have a broken part of my exhaust car, can I use this glue to stick a piece of metal to it for a long time? (I want to use this glue instead of welding)
If I was to try anything I would use JB weld. I did use JB Weld on a wood stove so that the latch would hold in place. I am not sure that it would work on your muffler but JB Weld works a lot better than the stuff showing in the video and JB weld comes in a larger size the tubes in the video are small and would take a lot more to attempt the job.
JBWELD - enough said.
JB Weld works good.
Thanks for the review! It looks like this glue is made for leaks only..
Your welcome.
Is it use to aluminium to aluminium how long its bonding ?
Not even 4 minutes in and he is going to fail! The piece on the wire cutter is supposed to pivot! If you "weld" it in, it will not work!
Yeh I know this stuff it's been around a long time now, many years, it used to be liquid metal it was called you could buy it in big tubes, it never worked then and it obviously still doesn't work. The idea is good but the product just doesn't work. Who wouldn't like to use a glue that actually worked for what it was made for, but such things are very hard to find. That plastic break, you might have more success using super glue with Styrofoam, there's a guy on youtube been doing this stuff, not tried it yet but I know the super glue and baking soda thing works pretty good. I suspect the super glue with the Styrofoam would work as it's a type of plastic and super glue works well on plastic, also it melts that foam making it a hard substance. But the metal part you might be better off trying to weld that back together or file it down and use a plate and attach the spring thing to the plate, if you still have the parts that is.
Does this work on plastic / PVC pipes?
It says it does.
JB Weld failed the same way though
Hi, is this glue good for exhaust? 🤔
The tubes have very little glue in them. I would try JB Weld.
No, its stands only for 200 celsius.
Basically, the Chinese sold you snake oil...
lol
Ohhh you didnt mix it enogh. Thats important.
Thanks Do you go by color ir just mix it longer.
@@JimMcLaren1950 the same a+b glue buyed from Aliexpress says mix very carefully, i mix it maybe 3 times lomger time than in video.. I have never failed and I'm surprised every time how really good this glue I've never tested the heat resistance, promised 200 celsius but I will some day in my empiric research😄
@@reioXyhi Thanks for posting.
السلام عليكم ورحمة الله وبركاته فين كيتباع هاد المنتوج
في ali express
Plase I wan oder
There is no web page to order from. Looks like they discontinued.
Chinese junk! What about JB Weld?
Tried JB Weld but not for Plastic or pliers.
@@JimMcLaren1950 it kinda does work for plastic and metal.
@@Nathan-lt6bw JB weld did work for other metal things. I used it on a stove where the latch wasnt catching. Built it up so the latch would hold. In place.
Chinese goods are good at advertising only
Exactly , it doesn't work as shown in their videos.