Terimakasih telah mengupload video tentang pengelasan SMAW akar 2G cap 7018 ini. Sangat berarti bagi saya. Salam hormat ⚘🙏
@DreamerDrafter Жыл бұрын
Pěkné, provařené od kořene. Pevnost 100%. Dobrá práce.
@milanzizka4636 Жыл бұрын
всё это красиво на стендах , я варю в насосной турбы 300/400 диаметром , до 50 атм ! там иной раз между трубами даже с зеркалом не подлезть ! а операции делать категорически запрещено , тренировался на обрезках труб варить в слепую на слух , долго мучался но пошло ! стаж 30 лет ВСЕМ ДОБРА
@user-iq4xt3me4u Жыл бұрын
Сварка - это жизнь и пока есть тепло, вода этого не замечают. Сделайте видео ваших примеров сварочных прийомов для народа.
@user-yp1bd4sl6f Жыл бұрын
.
@raymundoanastacio22573 ай бұрын
I've been melting electrodes since 1979 and I'm still learning, congratulations on the video and technical ability
@wmswesleymachado Жыл бұрын
sloppy at best
@kennethcrowe300 Жыл бұрын
@@kennethcrowe300 and at worst?
@theouter_banks7260 Жыл бұрын
@@kennethcrowe300 who cares welding isn’t a art competition it’s about getting shit done that works. Everything isn’t a pissing contest . I’m sure there are welders that make u look greener then the grass in spring . Just because you hate yourself so much doesn’t mean you gotta bring others down
@joebly564111 ай бұрын
@@joebly5641 you're right it isn't an art it is a trade and in a trade there is this thing called VISUAL INSPECTION If a weld is shit then it looks like shit aslong as your looking for the right thing unless you're working on playgrounds or hand rails for the middle of nowhere or welds that don't really matter and are just there to stick some random shit together for a quick gig then you would be correct...but for this shit it's quite important I would fail this plate just because of the sheer amount of undercut plus the hollows I saw on the arc shot Something I have to check off on a sheet everyday at work is uniform weld profile uniform length and width of weld bead.
@shaun-o436011 ай бұрын
@@joebly5641Are you a welder? If not, then shut the hell up🙄😂there is such a thing as visual inspection. 99% of the time, if that weld looks like shit, it probably is shit. After 40+ years of welding in steel mills and nuclear power plants, I have seen MUCH. And shitty, subpar welding is not acceptable where I'm from.
@robertlee48095 ай бұрын
This man knows what he is doing. Depending upon the place you're working. I was always told no cutting wheels on a weld test. Only wire brush wheels.
@davidnichols15684 ай бұрын
You can use tools, you just end up forfeiting some certs that require you use NO tools.
@angertone21322 күн бұрын
I'm new Lerner, from Bangladesh. Ur video is so helpful. Please make 1G and 4 pass video
@Mousume365 Жыл бұрын
Taí! Gostei da simplicidade na montagem do teste... Mais explicado que isso não existe! 👏👏👏
@Tadeu.7545 ай бұрын
Da , meseriaș adevărat. Felicitări.
@valicamardale8951 Жыл бұрын
That first pass was impressive, Using a grinder is a no no, I don't think it would pass, But you certainly understand what you're doing, You've got your attack angle correct.
@BartBullock-tf9hu9 ай бұрын
I welded and cut and bent both ways so many of these I get sick just watching you set this up. I had a box full of these test plates made up and had to weld them in every position. Predominately with 7018 but also 6010. I still have burn scares, laughing. Brought back old memories. Thank you
@johndavis3185 ай бұрын
Sy pernah belajar las seprti yg ada dlm video ini. Setahu sy untuk tembusan awal menggunakan kawat merah. Untuk keping baru kita menggunakan 7018 LH70. Waktu itu kota di bending menggunakan hidraulik press hingga membentuk U. Jika undrrcut dipastikan pengelasan akan patah atau retak.
@herrylumempouw53677 ай бұрын
Pěkné, řekl bych od Profesionála. V kořenu místy "vruby", ale provařený, s dobrým převýšením... 🤘
@stanley2166 Жыл бұрын
Na základní kurz dobrý.
@StepanGregor-no5zv4 ай бұрын
The whole point of welding is to melt both metals equally and to drag the rod if it is horizontal position, if you weld verticals than some rods like 6013 are perfect for vertical up, but do not try vertical down with that electrode, if you weld with 7018 than your arc needs to be very short, I mean you need to melt both pieces with same rhythm and move electrode, after some time you will get experience to make it routine.
@stefanm5636 Жыл бұрын
Рррррррииириирррриррикбирррирррр
@user-qs5so6nv9e Жыл бұрын
@@user-qs5so6nv9e 9
@1113562 Жыл бұрын
I would not do circular motion for the root. Just a drag with a short arc length. As long as there is weld protrusion at the rear. To me there was too much protrusion after the first pass. Good idea about tacking blocks on the ends to maintain the gap while welding across the width.
@1113562 Жыл бұрын
You can drag or pull the rod as long as the slag pool is behind the molten metal pool.
@zukispur5493 Жыл бұрын
Compare 1:30 to 2:49 and you will see there was something changed about the video sequence. At 2:49, the wing added to the right side doesn't have a hand grinder groove cut in it. You can tell at the very end of the first pass, the root, he was panicking because it was getting hot and about to blow out. I think there was multiple attempts at this root pass on different plates. Unless someone dictated such a large gap for the spacing on the root, I don't see the point. Cut landings on the plate edges and use less gap for spacing. A few extra amps and push the rod forward instead of dragging the root and you could easily watch it cut through without so much flipping back and forth and pushing so much puddle through the backside of the plate. Maybe the plates were prepared for him and that's what he had to use along with the required spacing? Who knows? No explanation given before video. It could be done easier as far as the root pass went. None the less, informative video.
@johnmorris7960 Жыл бұрын
Your comment made me laugh. My first thought was why an 1/8 gap with no land on the bevel? You are just asking for an unwieldy size keyhole 😅. I'm with you, tighten the gap, grind that knife edge of a bevel a nice land and kick up the amps and punch through. Should be easier to maintain the keyhole and get all the way across with a single electrode.
@whamburger4576 Жыл бұрын
Busted😂
@bojack274010 ай бұрын
.57 second tack becomes a weld ?
@Obijuuankenobi7 ай бұрын
@@whamburger4576look again. That gap he set appeared to a covered smaw electrode. At the very least it was 3/16, looked more like it was approaching 1/4 inch.
@spokes3183 ай бұрын
Nice job for a learner. Try half the gap with a 7016. Don't flick back and forth your chucking metal away. Keep the arc short and watch for the arc flame just licking through. If it gets too hot slow up and shorten the arc to cool it down or vice versa . This applies to all positions and trains the eye to watch the pool. First ten thousand bots are the hardest.
@timstone5112 Жыл бұрын
Hello sir ❤️ have a great day
@jewellerydesignerartists9353 Жыл бұрын
why don't you make a video showing how it's done? anyone can say do this or that...
@TVTruther Жыл бұрын
Retired two years ago having welded power station tube walls and steam turbine pipework,gas and oil pipelines, gas compressor stations, and hospital size boiler rooms. Being an old git I'm crap at videos and besides haven't got a piece of 6" 5LB in the garage so l can't help you there, sorry. You will come across someone somewhere that can knock six to ten of these out in a day to radiographic standards. I learnt from an older guy at work well after finishing a five year apprenticeship . Good luck.
@timstone5112 Жыл бұрын
@@timstone5112 so you can easily show how it's done on video.. do it... any clown can post I did this or that.. so what
@TVTruther Жыл бұрын
@@TVTruther we understand your point but tbh I don't see where this man disrespected or said anything wrong about the video. In fact, he tried to help.
@chadmoyer1453 Жыл бұрын
I took the all position test in 1970 and worked for Marion Power Shovel .
@larrylitzinger7441 Жыл бұрын
I'm Anele Mgqibela from Cape Town in South Africa I'm a welding student I've learn a lot thanks bro.
@anelemgqibela3305 Жыл бұрын
Anele. When practicing in your welding bay don't always have the practice peices on your bench. Weld some underneath the bench above the bench switching hands. Awkward positions. You'll thank me one day 🌚 oh and loosen your grip on the electrode holder.
@zukispur5493 Жыл бұрын
mucha socabadura
@miguelangelmichel6501 Жыл бұрын
Interesting video I'm a student from Cameroon...i do study in advance vocational training center and i will like to learn more from you sir
@user-js5ee2ep9q3 ай бұрын
Muy buena la presentación aunque note que eran probetas diferentes , mi pregunta es cuántas probetas se hicieron antes de subirla a presentar
@remmtz8378 Жыл бұрын
Boa noite iron essa é a segunda vez que eu me escrevi no seu canal parabéns pelo seu trabalho excelente amigo sucesso para você
@josepereira6428 Жыл бұрын
Good penetration good appearance w/out undercut and porosity reinforcement also accepted nice job tanks you!
@weldingartswithdomeng9424 Жыл бұрын
Очень хорошо, называется "маруськин поясок" мне нравилось варить горизонтали, хорошо заварено.
@user-dt9gg1py3e3 ай бұрын
It is very interesting to show the angle of the rod (side view) while welding: sometimes your rod is almost perfectly horizontal while other passes you aim much more up. Understanding the perfect angle in relation of the plate is i think key of making a perfect weld. Thanks!!
@therealspixycat Жыл бұрын
its 90• degree
@chongraxesh1 Жыл бұрын
Excelente trabajo saludos desde Ecuador bendiciones
@juanpazmino6604 Жыл бұрын
Root pass hot pass was 🔥you've made it like it is ez.
@johnvonmartin7501 Жыл бұрын
Keliatannya sangat mudah 😁tapi saya rasa menjadi tukang las itu tidak gampang 🙏skil anda luar biasa 🙏🙏saya salut dengan itu 👏👏👏
@DuniaFolding Жыл бұрын
I took that course in 1991, and I remember that in the 45° x 1/8 bevel, the penetration electrode was 6010, in negative polarity. Yo realice ese curso en 1991, y recuerdo que en el bisel a 45° x 1/8, el electrodo de penetración era el 6010, en polaridad negativa.
@argenisramosbaron6956 Жыл бұрын
Во-первых корень безобразный очень крупный Валик обратный громко тоже подрез идёт и последний валик тоже подрез потому что углом назад ввёл надо углом вперёд последний облицовочный вести Валик неправильное заполнение облицовочного шва последнего изначально очень крупный зазор и большое притупление можно было меньше притупления сделать и меньше зазор проплавление Аккуратнее будет меньше надо будет заполнять Это на будущее угол разделки будет меньше потому что из-за зазора и всё проплавится надо правильно собирать детали
@smellzagrwzoff3529 Жыл бұрын
EXCELENTE VIDEO¡¡ SALUDOS Y GRACIAS POR COMPARTIR¡¡
@hectorr814 Жыл бұрын
Hello sir ❤️ have a great day
@jewellerydesignerartists9353 Жыл бұрын
Muy bien amigo, solo que, creo que fue mucha abertura al principio para el fondeo, con 3/32 de abertura es mas que suficiente y con eso queda una bonita vista por atras.
@jesusbaez54687 ай бұрын
soldó de mas y se veia cochinon
@plazamarreservations31863 ай бұрын
Soy Nuevo en este oficio para mi no se ve malo
@boricuaarecibo9259Ай бұрын
As working student I just wanna keen about welding at the beggining when I found this I'm so interested I have some guild thank you I'm just learning of welding
@AkashiUnit Жыл бұрын
Gênio!👏👏👏👏👏
@CarlosHenrique-kg7qs Жыл бұрын
Great job. Thanks
@billarroo1 Жыл бұрын
Root pass had porosity. Cap was undercut. Grinder didn't have a guard.
@GrimDan1789 Жыл бұрын
He's welds would not have passed a bend test. I don't know how people think they can get all of the slag out without using at least a brush.
@samuelswearingen8435 Жыл бұрын
pushed into the top edge to much rather than letting the rod consume and fill it, which i think caused the undercut. i'm still in welding school, but i recently fixed my undercut issue for the cap passes on V-groove joints by watching how my instructor has literally 0 undercut on his cap.
@RobPulson6 ай бұрын
You're right... top cover pass needs more upward angle & push in to fill over the undercut
@rainsrapidly4 ай бұрын
Terima kasi bnyak titorial las 2g nya sir👍👍👍🤝🇮🇩
@FAUZIAKBAR89 Жыл бұрын
Probably a36 x 3/8 in thk plates.. cellulous root and lo hi capping rods... nice strings.. we use 6010/7016 combo here.. 🙏🙏🙏
@edsantos6627 Жыл бұрын
the essence of welding connects two materials into one
@Inspection_Tour Жыл бұрын
Perfect weld.👏👏👏
@enockjunior34489 ай бұрын
This welding peace I love this work.
@user-hl2ij7nv7h9 ай бұрын
Desbordarles el materia superior para que por la gravedad se deposite en la parte inferior . Y darles primero con selulosico . Esa es la formas correctas. Del soldador . Saludos desde lo lejos .🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷
@arseniovera672 Жыл бұрын
Qual a operarem que você está fazendo a solda?
@garanhum.clistfacil00289 ай бұрын
Сварочный шов нагрузил на 300%. Зазор между деталями слишком велик!
@guv2495 Жыл бұрын
В данном случае, показан способ сваривания, если такой зазор, попадётся
@simbiozful11 ай бұрын
Хорошая работа , только вот диск на балгарине поменять на ежа было вообще идеально ,ну как тут не при...😂 на ультразвук на наличие трещин
@ruslanoruslano20487 ай бұрын
Хорошие электроды.На вид-отлично заварил! Fine rodes, good job visually 💪
@MegaTubetraveller Жыл бұрын
👏👏👏👏
@ismaelantoniodasilva4647 Жыл бұрын
Кстати да. Сразу видно качество электрода. Шлак просто одной- двумя чешуйками отслаивается
@gatogordo2597 Жыл бұрын
Здравствуйте! Хотел спросить можно ли варить 1 см материала любом электродам. Или есть разница??? Мне дали 4 электрод сварка очень слабый когда варю постоянно прелипаеться к металлу. Начальник говорит это в проекте так должен
@user-ml6rk4tl1p Жыл бұрын
@@user-ml6rk4tl1pэлектроды просуши, ток добавь. Пробуй в два шва варить. Электрод 4 для металла 4-6 мм, ток 120-200. Сантиметровый металл варится электродом 5-6 током 220-320. Либо токами слабее и электродами тоньше, но в три-четыре прохода
@gatogordo2597 Жыл бұрын
@@gatogordo2597 спасибо за ответ сделаю!!!!
@user-ml6rk4tl1p Жыл бұрын
Very cool. I wish good luck to the author of the channel.
@DnevnikSvarshchika Жыл бұрын
Có vẻ như cái phôi đầu video đã bị hàn hỏng và đc thay thế bằng phôi mới. Khe hở chỉ để ở tầm 2,5~3,2 thôi. Khe hở ở điểm xuất phát nên bé hơn so với điểm kết thúc vì càng hàn thì nó sẽ càng bị kéo sát vào. Mặt phẳng 2 phôi nên bẻ ngửa 5 độ
@hanhvo4922 Жыл бұрын
Mantap....matur suwun ilmunya
@rikosumarsono837910 ай бұрын
Cool video. Seems like you did two runs. End plate was cut with the angle grinder but not after checking to stick number teo
@troelsgudiksen990011 ай бұрын
Excelente 👌
@WeldingFromPeru Жыл бұрын
I was taught to grind the bevel first at least 1-2mm to create root face so it would be easier for root pass.
@muhdirfan157910 ай бұрын
Very nice finished weld. Why no backing for the root pass? Although I never used it, they make a tape you can use for this. The root gap also seemed a bit excessive but I am not certain. I design heavy steel structures and refer to AWS D1.1 for preapproved welds for guidance. Anyhow, nice looking weld.
@hootinouts9 ай бұрын
this is open root that's why there's no backing
@methodicalvxp92658 ай бұрын
Mantap om 😁 tetap semangat 💪😊
@supasupe3575 Жыл бұрын
Hello 🤩 thanks 😍....but just a question,why 6013 for the roots?
@alexdissieux5137 Жыл бұрын
انا اشهدلك فنان
@user-wz8iw6ni1q8 ай бұрын
I did this schitt most of my life. I will tell you, I don’t miss it even a tiny bit. It’s a hard, nasty, hot, thankless job. Not to mention hazardous in a variety of ways. From burns to slag getting in your ear. Why anyone would want to do this for a living is beyond me. Haven’t picked up a welding rod in years and couldn’t be happier.
@earth_ling Жыл бұрын
Pengelasan sampai akar menambah kekuatan benda kerja..ini keren temanku👍👍
@BENGLASBERKAHCHANNEL Жыл бұрын
4G Welding Tips And Trick Bro Am India Sarver Watching Yoer video😮😮
@zkas85516 ай бұрын
Very informative content
@bvbmotovlog29328 ай бұрын
That's a good job
@user-yy5zy4xl8s7 ай бұрын
para mi parecer y despues de mas de 30 años soldando eso no se suelda asi, en primero lugar esta terminantemente prohibido la soldadura con electrodo rutilo ( 6013 ) lo normal es soldar con electrodo basico 7018, y esa forma de soldar estoy totalmente convencido que que hay poro en la raiz, en la posicion de soldeo en 2G se tiene que hacer como una especie de C con la parte superior mas larga que la inferior y sin avanzar mas que el material de aporte, este tipo de soldeo se podria realizar para uniones que no tengan demasiada importancia, como puede ser una barandilla, en el peinado has medito la amoladora y has hecgo un corte muy fino en el relleno de la pieza, tienes mucho riesgo por no afirmar por completo de falta de fusion entre pasadas, yo te puedo garantizar que esa soldadura no es viable para radiografia. deberias si es que quieres enseñar a la genta a soldar ese tipo de posiciones hacerlo bien , esa soldadura no es validad bajo ningun concepto
@danidanidani331 Жыл бұрын
正解，6.28秒就是一个严重错误，这板子RT根本不可能过！
@lianqishi10 ай бұрын
I don't know why I'm not seeing people calling this a fake. I've seen different sets of plates in this video and anyone who has ever welded an open root joint like that knows that a 6013 would not fill that huge root opening like that.
@spokes3183 ай бұрын
The gap is wider than I prefer, but to each their own. There was a lot of porosity in your root pass, but I didn't notice it nearly as much in the fill or cap. All in all, I think it would pass a bend test. 👍
@ArkansasUnderground Жыл бұрын
Wouldn't even pass visual inspection. There's so much undercut on the last cap pass, which he wouldn't even need to do if he didn't grind the hell out of it, which would also fail you at most places, since they typically only let you grind the root to feather, and the rest will be wire wheel only. The probable porosity and slag inclusion from pure chipping and not any brushing could potentially crack it during a test. That's assuming that they even let you go to bend it. But given that no country with safety standards uses Arabic even as a third language, it would probably be fine even if it did crack.
@volatile100 Жыл бұрын
@@volatile100 yea I didn't even notice the undercut on the top cap weld. That'd be a no go.
@ArkansasUnderground Жыл бұрын
@@volatile100what do you think caused it to undercut?
@TrillMurray Жыл бұрын
@Trill Murray Too hot and having too little angle are most likely causes for it to happen. In this case it's probably the heat, since bead profile isn't drooping down like it would with bad angle. Turning down the amps or letting the plate cool would fix it.
@volatile100 Жыл бұрын
@@volatile100 thank you! I really appreciate it.
@TrillMurray Жыл бұрын
Great job👍👍👍👍👍👍👍👍👍
@MrMopar413 Жыл бұрын
Надо срезать вводные планки по бокам. Показать сварной шов по срезу.
@user-bp6kv5bz9k Жыл бұрын
Hello sir ❤️ have a great day
@jewellerydesignerartists9353 Жыл бұрын
Там у него на корне поры , даже на камере видно
@user-gz8nf1lo8g Жыл бұрын
@@user-gz8nf1lo8g ну дак кто же на корне вперед-назад размазывает, и зазор там чет конячий был.
@user-ie1ie3jk4t5 ай бұрын
На просвет не пойдет. Для ученика еще более менее
@John_Smith_7776 күн бұрын
Great lesson master😊
@kopikooo84833 ай бұрын
Saran aja nih bang kalo bikin tutorial tu minimal kasi tau ampernya jadi kita sebagai penonton juga menambah wawasan.
@suryojinggosuryo7322 Жыл бұрын
뒷쪽은 용접을 하는 장면이 안나왔었는데 어떻게 된거죠?
@user-fi6cw6yf6o Жыл бұрын
No undercut No porosity No slag inclusion No tungsten inclusion No over spatter No arc strike Good penetration Perfect...
@junkjava28767 ай бұрын
Gostei da solda aprendi mais um pouco
@joseluizdearaujo7125 Жыл бұрын
Ça semble facile , mais c'est pas le cas 👍👍 je suis impressionné , bravo 👍😊
@sadrickghemari1629 Жыл бұрын
Mais qual seria a amperagem que está usando?
@gedeaobarros7908 Жыл бұрын
Горизонт, вертикал, потолок - только опыт приводит к хорошим результатам.
@user-bf5pu5ue3b Жыл бұрын
Luar biasa mantab penjelasannya sobat👍👍👍
@TAPANULITV89 ай бұрын
Yes you are right Robert Good joint does not mean it passes bend test,,visual OK,, but must pass bend test,,,
@canadamontreal7397 Жыл бұрын
A little more juice for good fusion, slag and crevice burnout, and use multiple stringer beads instead of weaving the fill.
@hariowen3840 Жыл бұрын
Lovely Root weld! well done, but please never clean slag off with cutting disk ! just chip it off with chipping hammer, bad practice really, regards.
@stormytempest6521 Жыл бұрын
I am seeing slag inclusion and porosity, but overall, not too bad on the beads.
@jeffreyullrich85119 ай бұрын
EL PROTECTOR DE LA AMOLADORA. RECORDAR MEDIDAS DE SEGURIDAD MINIMAS
@rauloribe2428 Жыл бұрын
Première passe électrode basique au moins. Bourrage et finition électrode au plus. Tenir l'électrode en arcs courts sinon votre soudure sera un champ de souflures sphériodales. D'ailleurs la première passe est toujours blanchie pour contrôler une bonne compacité du métal déposé.
@brunoblanc9883 Жыл бұрын
Super bro
@angasasikumar50788 ай бұрын
Bạn hàn rất đẹp ..❤❤❤
@tuhoangminh67210 ай бұрын
Bravo, Majstore.....
@lollol-pm5pq Жыл бұрын
Saludos desde cali valle del cauca Colombia, quiero agradecerle por el video te comento, La raíz se debe hacer con 6010 o 6011 para la penetracion de la raíz , luego se hace el relleno con 7018 y se procede a hacer la presentación con 7018 con cordones intercalados de abajo hacia arriba me parece que el proceso está mal de inicio ya que se uso un procedimiento inadecuado
@jesusrios376410 ай бұрын
Correcto eso no sirve pa un carajo 😂😂
@leimanduran26889 ай бұрын
Awesome 👍👍
@premkumaryadav73467 ай бұрын
The last weld seams I saw the porosity , perhaps your electrode was not at the ideal temperature ?Because if it were a welding test that board is rejected...
@gregorioruz8675 Жыл бұрын
Mantap bg metodenya mudah di pahami
@BengkelLasMultikaryateknik5678 Жыл бұрын
You are a good welder but the undercut would fail it in a bend test. No cutting wheels to clean it thats what caused the undercut which equals weak joint. Good video though.
@robertblackshear8963 Жыл бұрын
?🥔🥔🥔🥔🥔😊😊
@sdrafiqul6348 Жыл бұрын
V rezných kolieskach máš pravdu na 100%,ale zvaral veľmi dobre a pri koreni dodržal tvar hrušky aby vznikol koreň.
@romanbalaz918011 ай бұрын
@@sdrafiqul6348 ❤❤❤❤❤❤❤❤ цих
@user-zt9nu8di1i11 ай бұрын
I agree on the undercut. As a Boilermaker "certified, high-pressure welder, I noted several items. On the backside (root pass) the slag would seem to indicate some "push through". The weld tests, I've taken, would permit the use of a wire wheel on a grinder, but never a grinding wheel. That was grounds for fail. My certification tests were on schedule 40 tube with a test strip taken at 1:30, 4:30, 7:30, & 10:30. There would be a face bend, root bend then the ultimate two were given side bends. In over two decades I've never failed the cert test or on the job, had one of my welds fail ultrasound, magnaflux, x-ray. I never held the rod, to steady it, my idle arm was used to brace the arm with the rod holder.
@richardkawucha123211 ай бұрын
I remember taking my 3G stick welding test some 20 yrs. ago. We were not allowed any power tools. Only hand tools. Chipping hammer, wire brush, and some dental picks were all I could bring. Not even allowed a grinder at all doing the test.
@americanwelder98659 ай бұрын
Ferramenta amolada, fogo alto!
@ricardobacelar1706 Жыл бұрын
In a nuclear power plant welding test. A grinder is only allowed when cleaning mill scale on your test plates.
@10Flat Жыл бұрын
Des année expérience , bravo...
@tade769 Жыл бұрын
жаксы ислеген усындай кылып ислеу керек рахмет
@UMPKING7_YT Жыл бұрын
The world look good but there's one thing I know that heats up too high something's off because on a pretty Chevy 18 weld your flux should curl up behind and come off by itself as your welding
@williamgoring7605 Жыл бұрын
Top penetração Sangada top de mas. E acabamentos Lindo Meu Compadre ae Sim
@tassiohenrique3805 Жыл бұрын
Gambar pertama anda menerangkan proses pengelasan maju mundur.... Tapi saya melihat ada kegagalan di pola maju mundur sehingga mengakibatkan pembesaran jarak antara besi pada lasan... Dan anda berganti pola dengan pola berputar naik turun... Dan itu berhasil
@ryanwijayanto68795 ай бұрын
I wonder what his settings are on the welding machine?
@dijonezable2 ай бұрын
Terimakasih Ilmunya bang iron
@muhammadsuryadi3128 Жыл бұрын
En mi época no permitían hacer guía con el disco solo grata
@Victorsanchez-yg8lw Жыл бұрын
Muy bien esplicado pero no seve la estufa para tener los electrones calientes que muy importante y la raíz tiene muchas mordeduras que en una radiografía salen y te la rechazan
@venanciomartinez8163 Жыл бұрын
Mantap bos ku menambah wawasan dan ilmu
@AdiLas-my3xb9 ай бұрын
My sadistic weld instructor had us use 6010 for our certification welds. While the day class got to use 7018. He told us we’d thank him when it came time to get a job because we’d be better welders than the 7018 guys.
Terimakasih telah mengupload video tentang pengelasan SMAW akar 2G cap 7018 ini. Sangat berarti bagi saya. Salam hormat ⚘🙏
Pěkné, provařené od kořene. Pevnost 100%. Dobrá práce.
всё это красиво на стендах , я варю в насосной турбы 300/400 диаметром , до 50 атм ! там иной раз между трубами даже с зеркалом не подлезть ! а операции делать категорически запрещено , тренировался на обрезках труб варить в слепую на слух , долго мучался но пошло ! стаж 30 лет ВСЕМ ДОБРА
Сварка - это жизнь и пока есть тепло, вода этого не замечают. Сделайте видео ваших примеров сварочных прийомов для народа.
.
I've been melting electrodes since 1979 and I'm still learning, congratulations on the video and technical ability
sloppy at best
@@kennethcrowe300 and at worst?
@@kennethcrowe300 who cares welding isn’t a art competition it’s about getting shit done that works. Everything isn’t a pissing contest . I’m sure there are welders that make u look greener then the grass in spring . Just because you hate yourself so much doesn’t mean you gotta bring others down
@@joebly5641 you're right it isn't an art it is a trade and in a trade there is this thing called VISUAL INSPECTION If a weld is shit then it looks like shit aslong as your looking for the right thing unless you're working on playgrounds or hand rails for the middle of nowhere or welds that don't really matter and are just there to stick some random shit together for a quick gig then you would be correct...but for this shit it's quite important I would fail this plate just because of the sheer amount of undercut plus the hollows I saw on the arc shot Something I have to check off on a sheet everyday at work is uniform weld profile uniform length and width of weld bead.
@@joebly5641Are you a welder? If not, then shut the hell up🙄😂there is such a thing as visual inspection. 99% of the time, if that weld looks like shit, it probably is shit. After 40+ years of welding in steel mills and nuclear power plants, I have seen MUCH. And shitty, subpar welding is not acceptable where I'm from.
This man knows what he is doing. Depending upon the place you're working. I was always told no cutting wheels on a weld test. Only wire brush wheels.
You can use tools, you just end up forfeiting some certs that require you use NO tools.
I'm new Lerner, from Bangladesh. Ur video is so helpful. Please make 1G and 4 pass video
Taí! Gostei da simplicidade na montagem do teste... Mais explicado que isso não existe! 👏👏👏
Da , meseriaș adevărat. Felicitări.
That first pass was impressive, Using a grinder is a no no, I don't think it would pass, But you certainly understand what you're doing, You've got your attack angle correct.
I welded and cut and bent both ways so many of these I get sick just watching you set this up. I had a box full of these test plates made up and had to weld them in every position. Predominately with 7018 but also 6010. I still have burn scares, laughing. Brought back old memories. Thank you
Sy pernah belajar las seprti yg ada dlm video ini. Setahu sy untuk tembusan awal menggunakan kawat merah. Untuk keping baru kita menggunakan 7018 LH70. Waktu itu kota di bending menggunakan hidraulik press hingga membentuk U. Jika undrrcut dipastikan pengelasan akan patah atau retak.
Pěkné, řekl bych od Profesionála. V kořenu místy "vruby", ale provařený, s dobrým převýšením... 🤘
Na základní kurz dobrý.
The whole point of welding is to melt both metals equally and to drag the rod if it is horizontal position, if you weld verticals than some rods like 6013 are perfect for vertical up, but do not try vertical down with that electrode, if you weld with 7018 than your arc needs to be very short, I mean you need to melt both pieces with same rhythm and move electrode, after some time you will get experience to make it routine.
Рррррррииириирррриррикбирррирррр
@@user-qs5so6nv9e 9
I would not do circular motion for the root. Just a drag with a short arc length. As long as there is weld protrusion at the rear. To me there was too much protrusion after the first pass. Good idea about tacking blocks on the ends to maintain the gap while welding across the width.
You can drag or pull the rod as long as the slag pool is behind the molten metal pool.
Compare 1:30 to 2:49 and you will see there was something changed about the video sequence. At 2:49, the wing added to the right side doesn't have a hand grinder groove cut in it. You can tell at the very end of the first pass, the root, he was panicking because it was getting hot and about to blow out. I think there was multiple attempts at this root pass on different plates. Unless someone dictated such a large gap for the spacing on the root, I don't see the point. Cut landings on the plate edges and use less gap for spacing. A few extra amps and push the rod forward instead of dragging the root and you could easily watch it cut through without so much flipping back and forth and pushing so much puddle through the backside of the plate. Maybe the plates were prepared for him and that's what he had to use along with the required spacing? Who knows? No explanation given before video. It could be done easier as far as the root pass went. None the less, informative video.
Your comment made me laugh. My first thought was why an 1/8 gap with no land on the bevel? You are just asking for an unwieldy size keyhole 😅. I'm with you, tighten the gap, grind that knife edge of a bevel a nice land and kick up the amps and punch through. Should be easier to maintain the keyhole and get all the way across with a single electrode.
Busted😂
.57 second tack becomes a weld ?
@@whamburger4576look again. That gap he set appeared to a covered smaw electrode. At the very least it was 3/16, looked more like it was approaching 1/4 inch.
Nice job for a learner. Try half the gap with a 7016. Don't flick back and forth your chucking metal away. Keep the arc short and watch for the arc flame just licking through. If it gets too hot slow up and shorten the arc to cool it down or vice versa . This applies to all positions and trains the eye to watch the pool. First ten thousand bots are the hardest.
Hello sir ❤️ have a great day
why don't you make a video showing how it's done? anyone can say do this or that...
Retired two years ago having welded power station tube walls and steam turbine pipework,gas and oil pipelines, gas compressor stations, and hospital size boiler rooms. Being an old git I'm crap at videos and besides haven't got a piece of 6" 5LB in the garage so l can't help you there, sorry. You will come across someone somewhere that can knock six to ten of these out in a day to radiographic standards. I learnt from an older guy at work well after finishing a five year apprenticeship . Good luck.
@@timstone5112 so you can easily show how it's done on video.. do it... any clown can post I did this or that.. so what
@@TVTruther we understand your point but tbh I don't see where this man disrespected or said anything wrong about the video. In fact, he tried to help.
I took the all position test in 1970 and worked for Marion Power Shovel .
I'm Anele Mgqibela from Cape Town in South Africa I'm a welding student I've learn a lot thanks bro.
Anele. When practicing in your welding bay don't always have the practice peices on your bench. Weld some underneath the bench above the bench switching hands. Awkward positions. You'll thank me one day 🌚 oh and loosen your grip on the electrode holder.
mucha socabadura
Interesting video I'm a student from Cameroon...i do study in advance vocational training center and i will like to learn more from you sir
Muy buena la presentación aunque note que eran probetas diferentes , mi pregunta es cuántas probetas se hicieron antes de subirla a presentar
Boa noite iron essa é a segunda vez que eu me escrevi no seu canal parabéns pelo seu trabalho excelente amigo sucesso para você
Good penetration good appearance w/out undercut and porosity reinforcement also accepted nice job tanks you!
Очень хорошо, называется "маруськин поясок" мне нравилось варить горизонтали, хорошо заварено.
It is very interesting to show the angle of the rod (side view) while welding: sometimes your rod is almost perfectly horizontal while other passes you aim much more up. Understanding the perfect angle in relation of the plate is i think key of making a perfect weld. Thanks!!
its 90• degree
Excelente trabajo saludos desde Ecuador bendiciones
Root pass hot pass was 🔥you've made it like it is ez.
Keliatannya sangat mudah 😁tapi saya rasa menjadi tukang las itu tidak gampang 🙏skil anda luar biasa 🙏🙏saya salut dengan itu 👏👏👏
I took that course in 1991, and I remember that in the 45° x 1/8 bevel, the penetration electrode was 6010, in negative polarity. Yo realice ese curso en 1991, y recuerdo que en el bisel a 45° x 1/8, el electrodo de penetración era el 6010, en polaridad negativa.
Во-первых корень безобразный очень крупный Валик обратный громко тоже подрез идёт и последний валик тоже подрез потому что углом назад ввёл надо углом вперёд последний облицовочный вести Валик неправильное заполнение облицовочного шва последнего изначально очень крупный зазор и большое притупление можно было меньше притупления сделать и меньше зазор проплавление Аккуратнее будет меньше надо будет заполнять Это на будущее угол разделки будет меньше потому что из-за зазора и всё проплавится надо правильно собирать детали
EXCELENTE VIDEO¡¡ SALUDOS Y GRACIAS POR COMPARTIR¡¡
Hello sir ❤️ have a great day
Muy bien amigo, solo que, creo que fue mucha abertura al principio para el fondeo, con 3/32 de abertura es mas que suficiente y con eso queda una bonita vista por atras.
soldó de mas y se veia cochinon
Soy Nuevo en este oficio para mi no se ve malo
As working student I just wanna keen about welding at the beggining when I found this I'm so interested I have some guild thank you I'm just learning of welding
Gênio!👏👏👏👏👏
Great job. Thanks
Root pass had porosity. Cap was undercut. Grinder didn't have a guard.
He's welds would not have passed a bend test. I don't know how people think they can get all of the slag out without using at least a brush.
pushed into the top edge to much rather than letting the rod consume and fill it, which i think caused the undercut. i'm still in welding school, but i recently fixed my undercut issue for the cap passes on V-groove joints by watching how my instructor has literally 0 undercut on his cap.
You're right... top cover pass needs more upward angle & push in to fill over the undercut
Terima kasi bnyak titorial las 2g nya sir👍👍👍🤝🇮🇩
Probably a36 x 3/8 in thk plates.. cellulous root and lo hi capping rods... nice strings.. we use 6010/7016 combo here.. 🙏🙏🙏
the essence of welding connects two materials into one
Perfect weld.👏👏👏
This welding peace I love this work.
Desbordarles el materia superior para que por la gravedad se deposite en la parte inferior . Y darles primero con selulosico . Esa es la formas correctas. Del soldador . Saludos desde lo lejos .🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷
Qual a operarem que você está fazendo a solda?
Сварочный шов нагрузил на 300%. Зазор между деталями слишком велик!
В данном случае, показан способ сваривания, если такой зазор, попадётся
Хорошая работа , только вот диск на балгарине поменять на ежа было вообще идеально ,ну как тут не при...😂 на ультразвук на наличие трещин
Хорошие электроды.На вид-отлично заварил! Fine rodes, good job visually 💪
👏👏👏👏
Кстати да. Сразу видно качество электрода. Шлак просто одной- двумя чешуйками отслаивается
Здравствуйте! Хотел спросить можно ли варить 1 см материала любом электродам. Или есть разница??? Мне дали 4 электрод сварка очень слабый когда варю постоянно прелипаеться к металлу. Начальник говорит это в проекте так должен
@@user-ml6rk4tl1pэлектроды просуши, ток добавь. Пробуй в два шва варить. Электрод 4 для металла 4-6 мм, ток 120-200. Сантиметровый металл варится электродом 5-6 током 220-320. Либо токами слабее и электродами тоньше, но в три-четыре прохода
@@gatogordo2597 спасибо за ответ сделаю!!!!
Very cool. I wish good luck to the author of the channel.
Có vẻ như cái phôi đầu video đã bị hàn hỏng và đc thay thế bằng phôi mới. Khe hở chỉ để ở tầm 2,5~3,2 thôi. Khe hở ở điểm xuất phát nên bé hơn so với điểm kết thúc vì càng hàn thì nó sẽ càng bị kéo sát vào. Mặt phẳng 2 phôi nên bẻ ngửa 5 độ
Mantap....matur suwun ilmunya
Cool video. Seems like you did two runs. End plate was cut with the angle grinder but not after checking to stick number teo
Excelente 👌
I was taught to grind the bevel first at least 1-2mm to create root face so it would be easier for root pass.
Very nice finished weld. Why no backing for the root pass? Although I never used it, they make a tape you can use for this. The root gap also seemed a bit excessive but I am not certain. I design heavy steel structures and refer to AWS D1.1 for preapproved welds for guidance. Anyhow, nice looking weld.
this is open root that's why there's no backing
Mantap om 😁 tetap semangat 💪😊
Hello 🤩 thanks 😍....but just a question,why 6013 for the roots?
انا اشهدلك فنان
I did this schitt most of my life. I will tell you, I don’t miss it even a tiny bit. It’s a hard, nasty, hot, thankless job. Not to mention hazardous in a variety of ways. From burns to slag getting in your ear. Why anyone would want to do this for a living is beyond me. Haven’t picked up a welding rod in years and couldn’t be happier.
Pengelasan sampai akar menambah kekuatan benda kerja..ini keren temanku👍👍
4G Welding Tips And Trick Bro Am India Sarver Watching Yoer video😮😮
Very informative content
That's a good job
para mi parecer y despues de mas de 30 años soldando eso no se suelda asi, en primero lugar esta terminantemente prohibido la soldadura con electrodo rutilo ( 6013 ) lo normal es soldar con electrodo basico 7018, y esa forma de soldar estoy totalmente convencido que que hay poro en la raiz, en la posicion de soldeo en 2G se tiene que hacer como una especie de C con la parte superior mas larga que la inferior y sin avanzar mas que el material de aporte, este tipo de soldeo se podria realizar para uniones que no tengan demasiada importancia, como puede ser una barandilla, en el peinado has medito la amoladora y has hecgo un corte muy fino en el relleno de la pieza, tienes mucho riesgo por no afirmar por completo de falta de fusion entre pasadas, yo te puedo garantizar que esa soldadura no es viable para radiografia. deberias si es que quieres enseñar a la genta a soldar ese tipo de posiciones hacerlo bien , esa soldadura no es validad bajo ningun concepto
正解，6.28秒就是一个严重错误，这板子RT根本不可能过！
I don't know why I'm not seeing people calling this a fake. I've seen different sets of plates in this video and anyone who has ever welded an open root joint like that knows that a 6013 would not fill that huge root opening like that.
The gap is wider than I prefer, but to each their own. There was a lot of porosity in your root pass, but I didn't notice it nearly as much in the fill or cap. All in all, I think it would pass a bend test. 👍
Wouldn't even pass visual inspection. There's so much undercut on the last cap pass, which he wouldn't even need to do if he didn't grind the hell out of it, which would also fail you at most places, since they typically only let you grind the root to feather, and the rest will be wire wheel only. The probable porosity and slag inclusion from pure chipping and not any brushing could potentially crack it during a test. That's assuming that they even let you go to bend it. But given that no country with safety standards uses Arabic even as a third language, it would probably be fine even if it did crack.
@@volatile100 yea I didn't even notice the undercut on the top cap weld. That'd be a no go.
@@volatile100what do you think caused it to undercut?
@Trill Murray Too hot and having too little angle are most likely causes for it to happen. In this case it's probably the heat, since bead profile isn't drooping down like it would with bad angle. Turning down the amps or letting the plate cool would fix it.
@@volatile100 thank you! I really appreciate it.
Great job👍👍👍👍👍👍👍👍👍
Надо срезать вводные планки по бокам. Показать сварной шов по срезу.
Hello sir ❤️ have a great day
Там у него на корне поры , даже на камере видно
@@user-gz8nf1lo8g ну дак кто же на корне вперед-назад размазывает, и зазор там чет конячий был.
На просвет не пойдет. Для ученика еще более менее
Great lesson master😊
Saran aja nih bang kalo bikin tutorial tu minimal kasi tau ampernya jadi kita sebagai penonton juga menambah wawasan.
뒷쪽은 용접을 하는 장면이 안나왔었는데 어떻게 된거죠?
No undercut No porosity No slag inclusion No tungsten inclusion No over spatter No arc strike Good penetration Perfect...
Gostei da solda aprendi mais um pouco
Ça semble facile , mais c'est pas le cas 👍👍 je suis impressionné , bravo 👍😊
Mais qual seria a amperagem que está usando?
Горизонт, вертикал, потолок - только опыт приводит к хорошим результатам.
Luar biasa mantab penjelasannya sobat👍👍👍
Yes you are right Robert Good joint does not mean it passes bend test,,visual OK,, but must pass bend test,,,
A little more juice for good fusion, slag and crevice burnout, and use multiple stringer beads instead of weaving the fill.
Lovely Root weld! well done, but please never clean slag off with cutting disk ! just chip it off with chipping hammer, bad practice really, regards.
I am seeing slag inclusion and porosity, but overall, not too bad on the beads.
EL PROTECTOR DE LA AMOLADORA. RECORDAR MEDIDAS DE SEGURIDAD MINIMAS
Première passe électrode basique au moins. Bourrage et finition électrode au plus. Tenir l'électrode en arcs courts sinon votre soudure sera un champ de souflures sphériodales. D'ailleurs la première passe est toujours blanchie pour contrôler une bonne compacité du métal déposé.
Super bro
Bạn hàn rất đẹp ..❤❤❤
Bravo, Majstore.....
Saludos desde cali valle del cauca Colombia, quiero agradecerle por el video te comento, La raíz se debe hacer con 6010 o 6011 para la penetracion de la raíz , luego se hace el relleno con 7018 y se procede a hacer la presentación con 7018 con cordones intercalados de abajo hacia arriba me parece que el proceso está mal de inicio ya que se uso un procedimiento inadecuado
Correcto eso no sirve pa un carajo 😂😂
Awesome 👍👍
The last weld seams I saw the porosity , perhaps your electrode was not at the ideal temperature ?Because if it were a welding test that board is rejected...
Mantap bg metodenya mudah di pahami
You are a good welder but the undercut would fail it in a bend test. No cutting wheels to clean it thats what caused the undercut which equals weak joint. Good video though.
?🥔🥔🥔🥔🥔😊😊
V rezných kolieskach máš pravdu na 100%,ale zvaral veľmi dobre a pri koreni dodržal tvar hrušky aby vznikol koreň.
@@sdrafiqul6348 ❤❤❤❤❤❤❤❤ цих
I agree on the undercut. As a Boilermaker "certified, high-pressure welder, I noted several items. On the backside (root pass) the slag would seem to indicate some "push through". The weld tests, I've taken, would permit the use of a wire wheel on a grinder, but never a grinding wheel. That was grounds for fail. My certification tests were on schedule 40 tube with a test strip taken at 1:30, 4:30, 7:30, & 10:30. There would be a face bend, root bend then the ultimate two were given side bends. In over two decades I've never failed the cert test or on the job, had one of my welds fail ultrasound, magnaflux, x-ray. I never held the rod, to steady it, my idle arm was used to brace the arm with the rod holder.
I remember taking my 3G stick welding test some 20 yrs. ago. We were not allowed any power tools. Only hand tools. Chipping hammer, wire brush, and some dental picks were all I could bring. Not even allowed a grinder at all doing the test.
Ferramenta amolada, fogo alto!
In a nuclear power plant welding test. A grinder is only allowed when cleaning mill scale on your test plates.
Des année expérience , bravo...
жаксы ислеген усындай кылып ислеу керек рахмет
The world look good but there's one thing I know that heats up too high something's off because on a pretty Chevy 18 weld your flux should curl up behind and come off by itself as your welding
Top penetração Sangada top de mas. E acabamentos Lindo Meu Compadre ae Sim
Gambar pertama anda menerangkan proses pengelasan maju mundur.... Tapi saya melihat ada kegagalan di pola maju mundur sehingga mengakibatkan pembesaran jarak antara besi pada lasan... Dan anda berganti pola dengan pola berputar naik turun... Dan itu berhasil
I wonder what his settings are on the welding machine?
Terimakasih Ilmunya bang iron
En mi época no permitían hacer guía con el disco solo grata
Muy bien esplicado pero no seve la estufa para tener los electrones calientes que muy importante y la raíz tiene muchas mordeduras que en una radiografía salen y te la rechazan
Mantap bos ku menambah wawasan dan ilmu
My sadistic weld instructor had us use 6010 for our certification welds. While the day class got to use 7018. He told us we’d thank him when it came time to get a job because we’d be better welders than the 7018 guys.