What Causes a Spun Bearing in an Engine?
What is a spun bearing? Can you drive on a spun bearing? You can have a spun rod bearing or a spun crank bearing and when they fail, it sometimes destroys the engine like in our Lemons BMW. In this video I show you how to diagnose a spun bearing and possible causes. We disassembled the entire engine, every single nut and bolt, so you guys can see what causes an engine to throw a connecting rod and fail.
Our Backup Race Engine Being Built: • ChrisFix asked me to b...
Stainless Steel Headers: ebay.us/3OphJl
Chain Tensioner: amzn.to/3J5S7Uf
Timing Chain Cover Gasket: advanceautoparts.rt8x.net/4eMymL
Picking our Endurance Race Car: • How to Buy a Budget Fr...
How to Replace Power Steering Pump: • How to Replace a Power...
Complete Weight Reduction Episode: • How Much Weight can yo...
What Happened to the Lemons BMW: • What Happened to the L...
My FIRST Wheel to Wheel Endurance Race: • My First Time Racing a...
How to Install a Quick Release Steering Wheel: • How to PROPERLY Instal...
Completing my First 24hr Endurance Race: • What it Actually Takes...
0:00 How the engine failed
1:25 Installing the junkyard M54 engine
3:14 Stainless steel long tube headers
5:13 Backup BMW motor being built
6:44 What caused the motor to fail
10:20 What is a spun bearing
13:43 What causes a spun bearing
15:17 Oil analysis
18:17 Race car livery
→ As an Amazon Associate I earn from qualifying purchases.
→ Become a ChrisFix Subscriber: kzhead.info_c...
→ Instagram: / chrisfixit
→ Facebook: / chrisfix8
→ Website: www.ChrisFixed.com
→ My Channel Home Page: / chrisfix
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing.*
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
A common question in the comments is how can we have a junkyard engine and still be below the $500 limit and here is the answer: The goal of the 24hrs of Lemons is to try to level the playing field by having a bunch of junk cars race. This is the most affordable wheel to wheel racing in the world. Since our engine blew at our first race and we are putting in an equally junky 140k mile junkyard M54 engine which is what came stock with our car, the replacement engine does not count towards the budget. The new seals we installed to stop the oil leaks ($60) and the chain tensioner we installed ($6) does count and the headers ($100) definitely count but we were at $340 after selling everything we could from the car… So now we are at our $500 budget. I need to see if I can sell the cats because those are $400 but something tells me that we can’t haha. With that said, safety stuff does not count towards the $500 budget. Otherwise it’s impossible to race because the fire suppression system alone cost more than $500 and the cage cost $3800. Parts to make the car faster or perform better do count, but not stuff to save the drivers life. Now the “backup engine” is a good opportunity for a collab with another automotive KZheadr who wanted to get involved and is trying to grow his channel. We aren’t using the backup engine unless ours blows up again which I can’t imagine will happen (knock on wood). So that engine won’t count towards the budget because it’s not in the car at the start of the race. If we end up having to swap it in at the track, it still won’t count because the time it takes to swap it in will make it so we are not competitive anymore. The next race we would have to remove it and put in another junk engine or take penalty laps. Lmk if you have any more questions about the $500 budget. Again, the main goal is to prevent people dumping money into a car and have an unfair advantage because they have a bunch of money.
hey chris
so basically it's all the stuff that's on the car itself that counts?
@@OutrunRewind anything that makes the car more reliable or faster counts towards the $500.
@@CarSkull hey 👋
@@chrisfix Hello
My guy literally inspected and explained every aspect of an engine failure better than my engineering professors that brag about their phds shoutout to chrisfix ❤️🇪🇬
Instead of teachers and professors, schools should just play Chris's videos :D
💀💀💀so true
So true man. My teacher (im a certified mechanic) said to me, a spun bearing is nonsense. Well, screw him. I genuinely learned something.
@@PimSchouten What? He said that a spun bearing is nonsense? This guy is obviously not a certified mechanic... Smh..
😂
Excited for the next race! Your team is going to have a lot of fun and do great!!
Never expected project farm here lol
They claim they're making the most dependable BMW engine for Lemons racing. _We're gonna test that._ 😉
He’s the man that’s why he’s here
@@danielseelye6005 thank you 😂😂😂
Project farm next video on which is most reliable brand
The fact that you actually attempted an engine swap instead of giving up says a lot about you and your team. Can’t wait to see next year.
Thanks a lot! Here is next years video: kzhead.info/sun/jb6xnqh7gYaFq6s/bejne.html
@@chrisfix Oh, awesome!
I've never worked on a car engine in my life and only have basic knowledge on how an engine works, but the breakdown and explanation still made perfect sense to me! Love how you're able to take complex topics and break them down into an easy-to-understand video for even the non-mechanically inclined folks.
I’m excited for the next race, your team will be much better prepared 🏎💨 🏁
Lets hope that the next race will be better. 🙏
We will be for sure with your help!
Cant wait to see your next video of the machine shop: kzhead.info/sun/otN9hrSIiqKhimw/bejne.html
@@chrisfix Do you still have your new budget supercar, and why is there a red prius sitting in your driveaway. Are you next videos on those 2 cars
Glad Chris asked for your help!
Because of you Chris I got the courage to start my career in this field of work and I own my own shop now! Your the only one that made me feel like I had the ability to make it in thus industry
Yo thats sick. I hope i could open a shop as well. I hope youre doing well
Same! Chrisfix was a big influence and I was always interested in cars, so at 38 decided I had to give it a try, best decision I ever made! Anyone out there thinking about it, at least try, if you don’t you will regret it!
That is so awesome! Glad to hear that and it's exactly why I make my videos!
Damn, weird to see you here Logan, wishing you all the best I still remember when you got your first red camaro ss and posted about it!
would be awesome if i had more support in working on cars... currently attending a college but i dont feel like its what i want. i want this, i want to get my hands dirty and at the end of the day, take a look on a car and say "i revived this thing". thats what i want to do. hope i will find enough courage to do it like you guys!
That's THE...BEST explanation of a "spun rod bearing" I've ever heard and seen. Great job!
Thanks!
Chris Fix is the king of making car content that any level of mechanic can enjoy
Even after learning for years how internal combustion engines work I never knew how a spun bearing would damage the engine so this was quite interesting and I definitely learned something new , thanks !
Glad you learned something new!
Yeah it makes a big difference if you dont hear the sound and are in racemode so you might think the engine sounds good while its self destructing :) The car could have had very worn bearings from the start and if you buy a car and it sounds OK to you, there might be better condition cars that youve never experienced that could be the "normal condition" ones ;) My volvo 850 has some sound that feels like crank bearing knock but it still takes top speed runs and sounds normal when very warm. I'll let that old heap explode when or if it does :D It sounds "ok" and "normal for an old car" but if I compare it to my parents volvo with same engine thats been rebuilt few years ago its a night and day difference.
@@eamh2002 Ah I see that's very interesting but what about your volvo do you not care if it blows up?
@@ibrahimqureshi2420 It's a Volvo 850
@@eamh2002 yeah I'd like to hear a low mile version of the 3.0 v6 in my toyota, mine has 260k miles on the unopened engine and it runs and idles pretty smooth but it might be bad compared to a new one.
Yo this 24 hours of lemons series is gonna be absolutely legendary. Seriously I don't think any other content on KZhead can compare to the amount of dedication and entertainment you're putting into each and every video in this series.
Thanks a lot!!!
That explanation of the spun bearing was so gripping!
I love the explanation of this. I know a ton about metallurgy and it's so interesting to me that the problem was an oil problem -> bearing wear -> friction causing tons of heat -> heat changing the volume and properties of the metal -> and then an explosion. Heat is the BIGGEST problem with internal combustion engines and is absolutely the limiting factor for them.
I think it's important to also remember that oil gets really thin on the track. I actually would not use the factory recommended oil in this car. I'd consider going up to a 10w60 oil. I also recommend a product called Motorkote. I've been using it for years and it really does work. You can check out Project Farm's video on it, it will seriously save an engine in that kind of environment from being cooked. Even if it is a 240k mile worn out hoopty lol. I watched a friend run his chevy small block around the track for almost 20 minutes without realizing it didn't have oil in it (his oil pressure gauge stopped working). The only explanation we could come up with was that the Motorkote saved the engine
Thanks for the tip! I will look into it. We ran 10w higher than recommended but it might not be enough.
@@chrisfix 5w40 is what I run year round in my M54 in the northeast. The lifters like a heavier weight oil.
@@chrisfix this problem of your car smells like semi synthetic oil. use always full synthetic to reduce overheating
I track my bmw w/ the same motor, definitely invest in a oil pan baffle
I don't know about BMW but running thicker oil can over stress the oil pump and mess with the VVT system. Can confirm, 5w40 in a qr25de nissan engine will lead to engine failure.
You’re like the Mark Rober of cars and the passion and effort you put forth in these videos is absolutely amazing!
Thanks Marcus!
Fully agree
I think you should've also considered an overheated oil situation. Obviously oil gets thinner the hotter it gets and during prolonged race conditions it can reach temperatures of 130°C and more, which normal oils just aren't designed for. Also the warm oil weight (in your case 40) is measured at operating temperature (90-100°C), which is significantly lower than what you're gonna achieve on track. It means that you're actually getting thinner oil than you may have initially thought. To conclude i would personally run at least a 5W-50 oil, coupled with an oil cooler or at least oil temperature and pressure gauges to keep things in check in the future. Best wishes in the next race, love the content Chris!
Thanks for the tips!!!
I can confirm oil temps definitely affect the pressure. I run a pressure gauge on my dash and I’ve ran the car hot before at 220 (still in oem specs) but the oil was definitely hotter and oil pressure at idle was siting nearly 10psi lower than when coolant is at 180. I do have a factory oil heat exchanger that uses coolant but doesn’t help if the coolant is running at 220. Still made 75psi at higher rpm but definitely shows how real oil temps can affect its performance. Also that certain oils flash point really affect how well it holds up to heat. I’ve found liqui moly endures high heat a lot better than rotella t6 or castrol edge. For daily driving like a normal person, the “oil is oil” makes sense, but driving hard will separate the characteristics of different oils pretty well.
Yeah even my 110hp 1.8 celica had oil cooler
Misha made a video last year that described what kind of oil they run on their Ring Taxis compared to regular oil and also depending on the season. I think the suggest of investigating which kind of oil to run is good one
I didn't even consider this. Great thinking man!
I used to “pit crew” for my Dads boss doing dirt circle track racing with trucks. It was so different than what you guys are doing but there was one team that didn’t race all year. They had so many problems that they just couldn’t figure out but they came every other weekend just hoping it would work. Keep it up and I can’t wait to see the next race!
Thanks a lot!
That’s so sad but beautiful
I am an old mechanical idiot but can change basic things and follow instructions. I am most certainly a novice on this stuff but you break down what happens in a way I can understand. I find it so interesting how things work. I have so much respect for the knowledge that people possess and are willing to share. It is crazy how complicated things are that most, including me at times, take for granted. Thank you.
That parts layout table is FIRE! It looks so good. It's like those exploded diagrams from old school manuals, but in video form.
Thanks Brian! That’s exactly why I did it!!!
Let get fixing!!!! Hope you’re doing alright Chris
Thanks!
Pizza man. XD Nice name
@@chrisfix can you show a video on how to replace a Single battery cell for a 2005 Toyota Prius.
@@thejudgeexecutioner he did one for a full cell so I beleive it's close
@@malice6081 I saw that at one.
I was so sad when you guys didn't manage to get the new engine installed in time to complete the race, but you're all human and installing a engine in that short amount of time was bound to be difficult. Yes finally get to hear that glorious inline 6!!!
It sounds so good!
@@chrisfix It sure does!👌
Chris your videos are soo good that I willingly watch every ad to the end to make sure you get the commission, I don't think I've ever done that for any other youtuber. Thank you for the awesome videos man
This might be the most Thorough, I interesting, and informative on all KZhead. Great video.
Perhaps you could add on a oil pressure sensor. Also I love engine teardown and diagnosis, satisfying and I learn a ton out of it
We are! And I'm glad you learn a lot from the teardowns!
@@chrisfix Be sure to use an OBD tool that you have featured in your videos too!
One thing people in general should know is that "low oil pressure light" actually means "not enough oil pressure to even idle safely" (fuel pressure is not a fixed amount, it rises as rpms rise because the engine needs more oil in high rpms). When you get a low oil pressure light, immediately shut off the car. It will spin a bearing and do this quicker than you realize.
This why a lot of experienced Lemons teams have a seperate oil pressure sender set for a hot run or hot oil pressure...usually attached to GIANT trailer indicator light on the dash right in front of of the steering wheel. Drivers cannot be trusted to look at guages but a blinding light right in their field of view is hard to miss. Another is a coolant pressure light. In practice once up to temp the coolant system should be at at least 4 PSI and if it is, light is off. Second it drips below, light comes on. This is important because boiling coolant is still going to show about 212f on a temp guage which is a totally fine racing temp even as it is all boiling right out of the cooling system until you are totally dry.
You did a good job in the race, Chris. You worked hard, and tried everything to get back there, and you put your all into the race. Nice job Chris, never give up.
I totally appreciate how you channel has evolved, from simple topics of engine bay detailing to videos like this. Thank you.
Chris, you definitely have a talent for explaining things so that they are very easy to understand. That talent is not too common in the world from my experiences, keep up the good work!
Thanks a lot! Part talent but also lots of time and trial and error... but mostly lots and lots of time. For this video I spent 4 days filming, editing and then refilming parts I thought weren't clear and concise. I know people want more videos but I cant publish one I am not 200% happy with haha. I actually get my sister to watch the video when it's done and if she understands it, I know we are good to post haha.
I second this. There are alot of automotive channels of this type, no one does it like ChrisFix.
Very cool video man. I didn't even know about that aftermarket oil chain tensioner. I'm gonna check out that other video on the engine build now. Btw, don't you have to factor the cost of these replacement engines into the $500 budget? How does that work?
Thanks man! Since we blew up the engine at the race, as long as the same one or something crazy goes back in they wont count it against us. They just dont want you putting an LS or a Viper engine in there or something and making it unfair. An unknown junkyard motor that has a few new hoses and seals wont get us penalty laps... hopefully ;) haha
So basicly, your "500" dollar car exploded. It's now not worth anything. Even if it hadn't you just beat the shit out of a 500 dollar car for 3 days. Its value as far as the judges are conserned is 0. Replacing the same engine doesnt count against you. What could count are the upgrades hes doing to the replacement engine. but they arent actually in the car at the moment. In theory you could endlessly upgrade your car at the end of every race as long as it doesnt exceed 500.00 some of these teams race 4-5 times a year for the past 10 years.. they may look like crap.. but they are surprisingly well engineered by thier teams.
@@chrisfix Ah, nice. Did your teammate who worked on the replacement engine put new bearings in it? Might be something worth doing to prevent another blow up! 😬 They are pretty cheap, as I recall. When I did my rebuild, my main bearings didn't show much wear at all but the rod bearings definitely did for sure. Those can even be done with the engine in the car.
@@50sKid I had strongly considered doing so but I did not have the experience/knowledge/tools to check bearings so we as a team decided against it and I never checked any of them. The engine we got at the junkyard was spotless though, like some evidence of oil leaks that no one cleans up (typical lol) but other than that it was one of the best used looking engines I've seen so I think it was ok not cracking it open and letting all the magic out ;) I predict on my drift car my engine (2.5 with 265,000 miles lol) will shoot some component to the moon by the end of the season so when that happens, I would like to get a 3.0 and do a complete rebuild like you did. I went through your series on the rebuild and it was awesome!
Bearings are one of those things, yes you can replace them, but for the most part, if it isn't showing any issue just leave them or you could make it have an issue with them, a simple oil test. As you don't need to run Cats when racing, you could sell them off, and then the parts 'upgrades' are free/cost reduction.
Well done guys! Love your diagnostic breakdowns... you might want to consider bearing clearances for high endurance.. too tight could be a factor..
Thanks for the tip and thanks a lot!
@@chrisfix hi
Excellent break down of what happened. I did not know what a spun bearing was before this video, so thank you for the educational content; I always appreciate your videos.
Love to see a resealed and super clean engine replacement! Might as well flash an EU tune on the DME before the next race. Will go great with the catless headers and SAP delete! Great Job guys, looking forward to Jamie’s video!
It's pretty nice all put together now! And we will keep that in mind!
Thanks for the tip man! You think messing with the computer is a good idea for the endurance aspect of the car? We really dont need more power as much as we want reliability.
@@chrisfix ECU communicates with oxygen sensors on the cats for emission. Now, whatever it tries it will not help anything because theyre gone Flashing a tune professionally gets you a computer that gives the engine what it needs instead of trying to follow whatever regulations it was designed for Basically, done proper, you enhance reliability by flashing
@@chrisfix No problem! It might actually be better for long term as the extra airflow will be accounted for by the DME. The butt dyno probably won’t notice the difference but the engine should gain a couple HP too!
@@chrisfix EU2 tune is a stock tune that no longer cares for the SAP or post-cat O2 sensors. There should be zero negative effect on reliability as a lot of European E46s run it from factory. You can update it with winkfp and a $20 INPA cable off of eBay/Amazon. You can get the ZUSB (version number) from realoem. Look up "not so complicated install of BMW tools"
Does anyone else feel proud/really happy for Chris everytime he says "My Team"? He's come so far. Good on your Chris
Man, this video was super informative! I'm planning on building an engine for my car but for regular street use and occasional track use, so this was super helpful in understanding the flow of the oil.
Just you explaining how and why to your block makes me want to know more about engines... Thanx Chris. You're a heck of a guy!
@ChrisFix, I'm a former automotive powertrain engineer. When i was 16, I had no clue how cars worked. Thanks for making such awesome videos speaking about the chain of events. You'd be a great teacher.
That's awesome man!
The way you guys knolled those parts out on that table is _so satisfying._ It must have taken a while but it was totally worth it. It looks amazing.
Thanks a lot!!! It took 3 days to do that lol. Between the teardown and trying to figure out the best way to show the parts on the table and then removing the parts and taping towels on the table to make it easier to see. Such a simple thing in concept but as always, it takes forever haha.
@@chrisfix thank you for your great work Chris! Really appreciate it
Wow, good to know, I watch a lot of car videos on KZhead, I love the detail you said about HOW this motor failed. It really opened my eyes about things to watch out for. I am a engineer, I see things fail all the time but, the most things I want to see is HOW and WHY they failed and understand it. We can learn from others mistakes. It's something I lose sleep over. We can built it better. Thanks for a great detailed video.
This kind of videos help me a lot to better understand my automotive technician class in college :), thank you ChrisFix
Glad the video is helpful
Freakin' awesome breakdown, dude! Racing really demands details and extremes, and I love where this is going! Perhaps, you could consider ChrisFixRacing as another channel, and leave ChrisFix for the regular repairs on passenger vehicles? The attention to detail and analysis is sound. Keep it all up!
Thanks a lot! I cannot do more KZhead channels unfortunately. I already have ChrisFish too haha. I can include the good stuff on here and I will post any supplemental stuff on my IG.
you searched for everything probable causes when someone watch that takes so much khowledge really thank you
Hey Chris, if I were you I would re-weld those eBay headers. They’re known for being welded without the filler rod, which makes it easy for the welds to look good but makes them incredibly less strong then normal welds. Just something that could increase its reliability that much more
Thanks! I kinda want to try it out at the race. I will bring a spare just in case. Lets see if they hold up!
Exactly… what could possibly go wrong with unusually cheap EBay parts on a race car. 🤷🏻♂️
@@chrisfix hey Chris, I have the eBay headers in my E46 and they have held up great to tons of abuse!
I just searched up “project car” and started watching from when you first got this car, now it’s 6 AM and I wanna build an endurance race car 🏎️ ❤
Also INSANELY informative, I feel like I can build an engine just based on this video 😂 love the content
Do it!
I go back to this video after seeing the Great Comeback. Such a long journey with a lot of preparations and effort. It make today's succeed even more sweet. Hat off Chris 😀😀
Another stunning video. Just enough information to keep you informed and entertained without being overwhelmed with technical jargon. Thanks.
Thanks! That is the goal!
Agree, and the enthusiasm behind every single thing he says helps keep people interested and focused. Never a dull moment, no matter how technical or casual his explanation is in the moment.
ChrisFix getting into engine performance and building? Hell yeah!
Car detective? Chris just re-created the scene and I actually learned. Pffft and people say you can't learn anything from sitting at home watching videos. :D
That was the best explanation of a spun bearing that I've ever heard/seen. Thanks, ChrisFix!
Loved the forensic analysis of what happened and learned a great deal. Thanks for going into all the detail, as after watching your race video, I was very curious about what happened. I wish you all the best of luck, and safe travels always, on the next run!
Hi Chris, nice video ! I'm sure you already know some of these but as a former engine bearing expert, I would suggest couple of things to overcome this situation. It may be true that engine was badly maintained before the race, however it can encounter the same destiny within a short period in race conditions with standard bearings. It is very likely that coating is completely worn out in that con-rod, oil clearance is increased and thus oil pressure is dropped. 1) So high of a rpm for a long time, such as an endurance race, cannot be handled well by a babbitt coated bearing. This coating is very very soft and will wear out quickly even if you replace them with brand new ones. Babbitt coatings also start to detoriate after 180 C, which is very likely to happen during an endurance race. I can see that damaged bearings' brand is Glyco. I'm pretty sure that there is appropriate replacement bearings which are "sputtered". In this case upper con-rod bearings will be coated with much harder material, which will wear out much slower and will handle most of the beating coming from pistons. In this case, lower bearings should still be babbitt coated to embed all the dirt coming from oil with soft layer. 2) Consider using polymer coating ,preferably on top of sputter coating. This will enhance the emergency lubrication properties of the bearing surface especially for short periods of oil starvation (such as cornering etc.). Polymer coatings basically provide dry lubrication properties when there is not enough oil. Extra thickness that comes from polymer coating should be considered in terms of oil clearance ! 3) For race cars, oil clearance should be adjusted slightly higher than a normal street car. Otherwise, at high pressures during race, oil will be squeezed out of the bearing, leaving the bearing less than ideal oil amount.
Do you recommend adding additives like LiquiMoly Ceratec to the engine oil?
Your take was very helpful. I am a novice bearing engineer (hydraulic actuator bearings). I was wondering, does higher rpm require higher oil pressure to ensure oil film??. Also does changing the oil clearance require a change in oil pump/system change from stock??. Thanks!
my bearing spun & they said they found fine metal in oil because of it. I haven’t drove my car as far as a mile since the bearings spun. Do you think the engine can be rebuilt or am I likely to have to buy a new one
@@bpknows1 hello, depends on the situation of the crankshaft...
Great video! Such a clear explanation. I've heard the term "spun bearing" many times before and knew it was bad -- but now I really know just how bad it is.
Awesome video as always! I knew the term "spun bearing", but honestly until this I never exactly knew what that was. Thank you so much for always being informative, while always being entertaining. Side note, love the use of the address from back to the future with your oil sample. Great little easter egg there!
You did a great job explaining how an engine works to a layman. Keep up the good work!
Hey Chris, I just wanted to tell you. You've inspired me in the past 2 years. I'm only 13/2 years old, and I've learned so much for you! Thank you for all the informative videos.
Chris Fix brought good relations between China and the U.S
General secretary aren't you 68 years old bro
I'm glad you've been learning a lot and got inspired from the videos!
@@pillar43 I'm *69* nice
Hope putin watches chrisfix,
You have been a real inspiration to me I've been waching your videos for a long time now and because of you I have turned my 1990 camaro into a drift machine
I like your videos so much I had to stop and come back the next day to finish the video. Not leave and forget, or just outright leave with no intention of coming back. LEFT and CAME BACK. The best compliment I could ever truly give.
I had a spun bearing on my N63 a few years back, after watching this video, it finally made sense on what exactly happened. Thank you for explaining it so well. :)
15:47 lmao christopher fixtopher had me dying XD
I only want to congratulate you for the phenomenal leap of faith you took six years ago 👏👏👏🏆. Am about to take a plunge on a different path focusing on another industry, Thank you for the selfless inspiration and advice Chris🙏.
I remember when this guy was a diy how to mechanic and now he's got his name out and is racing and everything that's awesome keep up the good work
Thanks for going in-depth on the starvation issue. I’ve heard of spin bearings and understand the issue but this provides a comprehensive overview of what is going on and how things can go wrong.
*👆👆👆Thanks for watching send a direct message right away on the above number immediately☝️☝️☝️for more ❤️ ❤️ enlightenment•••*
Chris you inspire me to pay attention to detail and to always give my best in everything I do. Thank you!
I learned more in KZhead more than I ever learned in school nice job keep it up
Haha thanks!
Welcome
This is a great video dude. It’s the best demonstration of how these bearings work and fail that I’ve found.
I learned a lot from this video. Your diagnosis of finding out the cause is very clear to understand. Thanks for your sharing and your great team as well.
Great video! Really liked the root cause investigation you did and especially the data logging or RPM and coolant temp. Not only did you fix your BMW, but learned what went wrong and came out smarter and more prepared for the next race. One question I do have - are you going to install an oil pressure gauge now?
The amount of information of the engine running amazes me. Very cool video and info and even better team. The best of the luck for the next race, love you guys. Greetings from México.
Chris, your videos are the best, the way you explain how the engine work is amazing. really love your content! please upload more of these.
Glad that Chris used the proper term: oil GALLERY. Not oil galley. A gallery is a passage that, in this case, your engine lubricants flow through. A galley is the kitchen on a boat
Very consistent presentation in analysing what really happened. Mind blowing but very useful. Thanks again ChrisFix. I also love the way you elevated your driver's capabilities thus eliminating human error. Such a noble gesture. Educational and entertaining video.
I've learned more about my M54 in 20 min than the whole 14 yrs I've owned it. Thanks man love your vids
Very well explained but I wouldn’t except anything less coming from ChrisFix. I really learned a lot and I can’t wait to see you in the track soon.
I'm happy you explain things concisely and make it easy to understand. You're very good at this, Chris.... Thank you!
Thanks a lot! I spend a ton of time trying to do that so it is awesome to hear!
Love to see that oil analysis. This is such a cool video. As an oil analysis chemist who doesn't get to wrench on many engines, this definitely helps give me more insight into diagnosing certain oil samples. I honestly was expecting those wear metals to be wayyy higher just by looking at the damage. Let me know if you want some oil analysis kits! Keep up the amazing videos :)
I'm very excited in Chris and his team doing their second endurance race next year! I hope your team learned alot in your first endurance race
This was some nice insight into the mechanics of the internal components of an engine. I don't think I'll ever be the one trying to diagnose worn bearings, but good information nonetheless
Thanks! It's something you dont get to see every day!
Man this was an awesome in depth analysis. It actually helps me out, I had a similar issue happen to my vehicle. Engine blew a rod and the auto care service that was driving it at the time had it “inspected” and claimed it was just natural ware and tear. It’s hard to believe only because I took very good care of the vehicle and changed the oil per recommendations. This helps understand more of what could have potentially happened, so I really appreciate you breaking it down (pun) like this.
A shop blew your engine? Sounds a new, free engine is in order to me lol
How many miles did the engine have on it?
@@sufferr2914 it had 175k miles. Zero engine issues prior.
@@kpeezy765 Yeah sounds like you should get a new engine on the house
Chris, thank you for illustrating what a spun bearing is. I have read it a few times and heard about it many times, but did not understand it clearly until I saw this video. You have gained a new subscriber.
Glad it was helpful!
Loved the engine analyzing part after failure.
Chris I legit have been watching you since the beginning and I absoloutly love everything that you do! ❤ Hope you and your family are doing well❤
Thanks for the ongoing support!
@@chrisfix OMG it's so incredible that you replied!!! Love from syria my man❤
Bravo! After having enjoyed and been learning from so many of your videos over the years, this series is not only entertaining and exciting, but offering education and understanding of an ICE engine at a level I had not thought I could absorb. Well done - thank you!
No problem! That was the exact goal I was going for even tho we blew up the motor haha
Bro...his explanation was just on point 🤌🤌 love this channel
Thanks, I stopped working on BMW's when I ran into an early-2000's Z4 with a carbon fiber valve cover. Dealer, parts store, no one would warranty. Love the engine breakdown, like 2vintage channel, always a teaching moment
Well Chris, that was the best "Post Mortem" explanation I've seen. I agree about Oil Pressure gauges.. I have an old 95 MB and it drives me crazy having no Oil Pressure gauge. Anyway.. you'll get em' next time. Also, you can't win if you don't finish and you drove really well (to finish). Cheers
I've been working on my own cars for years and I've learned so much from your videos. Thanks man. If I had more time I'd buy a German car again because I like the way they drive. The ones I had were too unreliable, even with regular maintenance.
After experience comes Wisdom Chris... Here's to you and your team finishing next years race...💪💪💪
Glad to see that the lemons car is back into business, I’ll be waiting for the next race, good luck
Great video! I loved the failure analysis of the broken engine. I'm an automotive engineer and learned a lot!
Thanks a lot
Chris is such a positive person, excited for the next race!
That was an absolutely fascinating explanation of what happened. I also learned the importance of oil.
Love this series as someone with an E46, I remember not having a car and watching this channel and now I have the same car as Chris. I have also done a lot more to my car than what Chris has here but maybe we can see some more videos of this car and maybe it will get some more sophisticated engine mods.
Really happy with your positive take-aways. One of the hardest things to get new drivers to understand before they get in the car is the need for practice entering the car, exiting the car, and pit stops/fueling. I don't know if you've seen it yet but Mark Petronis has a video titled Survival about a near fatal wreck he had. Since his wreck he has been an extremely positive voice for safety in our hobby and I really appreciate you taking it so seriously in this series! Keep up the good videos.
Thanks a lot! At our practice day we will be going over that a bunch of times!
Thanks a lot man! Is Mark the guy with the Vette that wrecked and he was unconscious? If so, I read all about that and from that day on I said we are adding an auto fire suppression system!
@@chrisfix Yes he is! My primary non-lemons track car is a Corvette and I use several parts his company makes. He's always been really active in the corvette track community and is a very talented driver so when he had his accident it really brought home that we practice safety because of what can go wrong not because of what we expect to happen. I'm really excited to see the automatic fire suppression install, I haven't put one in yet but I've been looking at it for the same reasons!
Awesome breakdown. Super excited for the upcoming vids!!!! Also looking forward to drift season with the stang :)
What an awesome and thorough explanation, I definitely understand spun bearings better. thank you
Hey chris, it would be so awesome if you made a step by step engine rebuild video. Like disassembly, upgrading pistons rods, bearings, Crankshaft, oil pumps, ect. Your videos are awesome, thanks for the good information.
Do a reinforced oil pump for the M54, it will fail again (been there), and also, add trap doors to the sump to prevent oil starving in fast corners.
Thanks for the tip!
Yea a trap doors in the sump are important, friend's brother had a LS lockup because it was starved on the track
Wow, I've been a subscriber for a very long time but life happened and I had not seen any of your videos in more than a couple years. I'm shocked and happy to see how far you have come. That explanation was on point and I learned so much! Thanks man. You deserve all the success coz you are one hard working KZheadr.
Thanks a lot
man, i learned so much from this video today. that cam bearing explanation was really something. the datalogging too.
*👆👆👆Thanks for watching send a direct message right away on the above number immediately☝️☝️☝️for more ❤️❤️ enlightenment•••*
We're so excited for the next race !
Sick analysis Chris!! When's the next race? I'm really stoked about this series and rooting for you guys to win.
June 10-12! We are pumped!
Can't wait, really unique experience!