KZhead
Тәжірибелік нұсқаулар және стиль

9 Amazing Electrical Tricks That Will Make You Level 100 Master

Creation Holic
2023 ж. 19 Шіл.
1 775 585 Рет қаралды
Жүктеу

Hello everyone! You are watching video "9 Amazing Electrical Tricks That Will Make You Level 100 Master"
I hope you enjoy watching my video!
► Subscribe: bit.ly/Creationholic
On Creation Holic channel, you can learn various inventions, science projects, crafts and DIYs teaching how to reuse or recycle.
© Copyright by Creation Holic ☞ Do not Reup
#tipsandtricks #diy #tips

Пікірлер

  • ❗Please enable subtitles in your language 🙋🏼‍♀ Thanks for watching 😋🤗😘

    @creationholic101@creationholic10110 ай бұрын

    • Franca😢

      @user-ws4fl4pg1x@user-ws4fl4pg1x9 ай бұрын

    • ¹¹¹ 😂​@@user-ws4fl4pg1x

      @angelramonrigal6677@angelramonrigal66774 ай бұрын

  • Ad 1: mindblowing Ad 2: the twist and extra stress can damage the metal wires. However the risk would be very small, no problem. Ad 3: nice idea! Ad 4: this might work if the remote can operate with just single battery. Which is sometimes the case, there are step up circuits. But even then a wire would be better than a pencil. Graphite has high resistance. Ad 5: another nice idea Ad 6: the last option is not better than the first one. The second option works better because there is longer path of the wire which would need to slide. Friction is therefore much higher and so the force needed to pull it out is higher. The third option does not extend the path much. Only the small part on right needs to move. And once it is pulled out then only the small part at left has to move. They don't get stressed at once. The force therefore does not go up much. And having two pieces of wire next to each other could actually decrease the friction if the metal piece is not reasonably flat. Option 3 is not an improvement. Use options 1 or 2. Ad 7: this one often works. What you do here is replacing a LED by a wire. LEDs cause a voltage drop. Wire does not. In order to provide a light there must be a current flowing through the LED. Too high current means it burns out. Now let's imagine you have power source of 48V and you use 12 LEDs where each one has 3V drop. Combined they do 36V drop. Each needs 20mA of current. To limit the current you use a resistor which would be 12V / 20mA = 600 ohm. The resistor would dissipate 0.24W of heat. Now, to the point. You replace one LED by a wire. So the voltage drop of the remaining 11 LEDs is only 33V. The voltage on the resistor is up to 15V. It will give current of 25mA and power dissipation would be 0.375W. Will the LEDs survive that current increase? And won't the resistor overheat? Real situation is even worse as the manufacturers want to decrease the power lost on the resistors and so use LEDs which have voltage drop lower than the source, but still as closest to it as possible. Replacing even a single LED by a wire could then easily mean the resistors would overheat and bad things could happen. Do not do this unless you have the schema and skills to evaluate the risk involved. Ad 8: works on non-critical wiring. Which means 99.9% of wiring around us. No problem with this either. Ad 9: another perfect idea!

    @karelberanek1007@karelberanek10079 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!

      @creationholic101@creationholic1019 ай бұрын

    • Replying to @ karolberanek1007 DARZHNARZHERFLARVERSHARVER? DARZHNARZHERFLARVERSHARVER?

      @tompsheridantsheridant7354@tompsheridantsheridant73549 ай бұрын

    • Uzb; Ad 8: men qilib ko‘rganman, tasma chiroqda 50 ta LED bor edi, 2 tasi singan edi, olib tashlab sim bilan ulab qo‘yganman, ishlab ketgan Eng; Ad 8: i tried it, the strip light had 50 leds, 2 were broken, i removed and rewired it, it worked

      @faxriyoralimov-2211@faxriyoralimov-22119 ай бұрын

    • Thank you so much for explanations! Nice video and it Is even more useful having in mind your comments.

      @markotesic8758@markotesic87589 ай бұрын

  • The coax cable repair shown will introduce an impedance mismatch at the location where it is spliced. Probably not an issue on receive but could be an issue for a transmitter. To keep the impedance you'd have to use BNC or N type connectors instead of the splice shown.

    @vk3fbab@vk3fbab9 ай бұрын

    • Hello! thanks for your recommendation. Wish you all the best!

      @creationholic101@creationholic1019 ай бұрын

    • @vk3fbab Using a strong enough transmitter makes this much less of a problem though because none of your pets will ever chew a cable again 😉

      @matthiaslastname9019@matthiaslastname90199 ай бұрын

  • 4: No need to cut a pencil. You can use one old battery instead.

    @the_wishmaster@the_wishmaster9 ай бұрын

    • Hello! thanks for your recommendation. Wish you all the best!

      @creationholic101@creationholic1019 ай бұрын

  • Semua teknik di konten video ini super kereeeeen

    @Sahabat-YouTuber-Pemula@Sahabat-YouTuber-Pemula8 ай бұрын

  • @ number 2, just buy a proper plug with tension relief. It’s default on any non-garbage plug.

    @Engineer9736@Engineer97369 ай бұрын

    • Thank you for sharing your feedback and expressing your perspective

      @creationholic101@creationholic1019 ай бұрын

    • And use proper wires )))

      @rotten-Z@rotten-Z9 ай бұрын

  • مبدع والله وننتظر منك المزيد وبارك الله فيك

    @AliOmar-qz8lf@AliOmar-qz8lf9 ай бұрын

    • Hello! welcome to Creation Holic channel. I am very happy to read your comment. Wish you have a nice day!

      @creationholic101@creationholic1019 ай бұрын

  • Nunca vi un control remoto que pudiera funcionar con la mitad de la tension de diseño

    @shusaku4@shusaku49 ай бұрын

    • I tried it and it works, you can try it

      @creationholic101@creationholic1017 ай бұрын

  • Excelente trabajo

    @jairnicolassandovaltrivino9813@jairnicolassandovaltrivino98139 ай бұрын

    • Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1019 ай бұрын

  • Putting uncrimped stranded wire into a screw terminal is enough to ban you from any kind of master title for all eternity.

    @feynthefallen@feynthefallen9 ай бұрын

    • Also, proper plugs have strain relief clamps that are designed to clamp onto the isolation and hold it in place. I don't know in what kind of backwards place you live in that you even HAVE plugs like that, but the only receptacle this plug should be in is a trash bin.

      @feynthefallen@feynthefallen9 ай бұрын

    • Thank you for sharing your feedback and expressing your perspective

      @creationholic101@creationholic1017 ай бұрын

  • brilliant mate. Australia

    @kengoold7157@kengoold71578 ай бұрын

  • Trik dan tips yg sangat menakjubkan

    @FahrulRozi-cu1rr@FahrulRozi-cu1rr9 ай бұрын

    • "Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things! "

      @creationholic101@creationholic1019 ай бұрын

  • Tipp 2. solche Stecker dürfen in der EU nicht verkauft werden. Natürlich Arbeiten ohne Adernendhülsen. Die Schraubendrehergröße stimmt auch nicht.

    @peterwalch8762@peterwalch87629 ай бұрын

    • Es ist erschreckend, was hier für „clever“ verkauft wird. LED löten, einphasig abgeschaltet… Top-Idee! 🤦🏻‍♂️🤦🏻‍♂️

      @marcsiegel3358@marcsiegel33589 ай бұрын

    • Thank you for sharing your feedback and expressing your perspective

      @creationholic101@creationholic1017 ай бұрын

  • Tuyệt vời 🎉❤.vietnam

    @Nguyenvanlong77@Nguyenvanlong779 ай бұрын

    • Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1019 ай бұрын

  • I am spaniard, from Cartagena Spain. ... and I am very pleased for your teaching videos ... thanks a lot

    @primera1ra385@primera1ra3859 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your support

      @creationholic101@creationholic1019 ай бұрын

  • Good job! 👍💯👍💯👍💯

    @UC_Tiger_SW@UC_Tiger_SW9 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic1019 ай бұрын

  • very good

    @CreativePassion88@CreativePassion8810 ай бұрын

    • Welcome to Creation Holic channel! Hope you have a good time while watching the video!

      @creationholic101@creationholic10110 ай бұрын

  • ❤ very useful ❤

    @rashidmahmoodjutt5988@rashidmahmoodjutt59889 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic1018 ай бұрын

  • Superbes idées 👍👍

    @stanislaspuskarczyk6887@stanislaspuskarczyk68879 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic1019 ай бұрын

  • ماشاءالله،عالی بود، آفرین

    @mohammadrezasaraei9561@mohammadrezasaraei95619 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic1019 ай бұрын

  • Mẹo rất hay!

    @HL3108@HL31089 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your support

      @creationholic101@creationholic1019 ай бұрын

  • Cám ơn bạn.Rất tiện ích

    @tantran9133@tantran91339 ай бұрын

    • Hello. Welcome to my channel. Thank you for your feedback!

      @creationholic101@creationholic1019 ай бұрын

  • Ini sangat bagus sekali

    @astahariyanto@astahariyanto19 күн бұрын

    • Thank you for watching

      @creationholic101@creationholic1016 күн бұрын

  • Thank you!

    @lagofranco7197@lagofranco71978 ай бұрын

    • Welcome to Creation Holic channel! Hope you have a good time while watching the video

      @creationholic101@creationholic1018 ай бұрын

  • Great idea

    @BHK_DIYAtHome@BHK_DIYAtHome9 ай бұрын

    • "Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things! "

      @creationholic101@creationholic1019 ай бұрын

  • Thanks

    @shaxawanchya3310@shaxawanchya33108 ай бұрын

  • Ótimo vídeo! Gostei demais do ritmo dado, geralmente são cortadas várias etapas do processo para deixar o vídeo mais rápido, mas o formato pelo qual optou me proibiu de assisti-lo em velocidade acelerada o que ajudou e muito na absorção das dicas. Também gostei dos textos inseridos ao longo do vídeo. Parabéns pela coragem de fazer diferente!!!

    @charleslisboa9531@charleslisboa95319 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!

      @creationholic101@creationholic1018 ай бұрын

  • 두번째 반단선 위험 있습니다. 전선화재 위험. 전선은 구부리지 않은 일직선이 가장 이상적입니다.

    @user-jl9yn1ct9w@user-jl9yn1ct9w7 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1016 ай бұрын

  • While watching this spectacular video, I can't help but wonder about one thing: I own rental properties, and I perform all the maintenance and repairs myself. To keep things organized, I have bins with parts and tools seperated by category: Plumbing, Electrical, etc. That's where my question comes from: Do people outside of the US have a kitchen "Junk Drawer" ? I'd welcome input from everyone, all around the world. If you know someone outside 5US, I'm eager to hear their answer. GREAT video !!!!!

    @GB-go6gp@GB-go6gp9 ай бұрын

    • @GB-go6gp - From my experience as a 64 y.o who lives in Australia, I find usually women of older generations have these kitchen junk draws, or males who are not handyman types. We had one at home of sorts ( metal biscuit tin full of junk and household fittings ( picture hooks, wire, string, insulation tape, batteries, screws & tacks for carpet etc ). When I was a teen, Dad & I used it most of all. However, if you have a male in the house who is the handyman type ( like me ) these days he's most likely got access to a garage full of tools with bits & pieces.

      @kimbal1958@kimbal19589 ай бұрын

    • @@kimbal1958 Well, I'm certainly not an older woman ("well I can't just call you Man"). I am however, the aforementioned handy-man, and I have a well organized, albeit small junk drawer. While I do have a garage full of tools, the small, unpowered tools that I use frequently reside in my junk-drawer.

      @GB-go6gp@GB-go6gp9 ай бұрын

    • Hello, you are such a nice person to have left me a comment! With a dream to contribute to making the world a better place, I really need good and useful ideas and solutions! If you have any other great ideas please share with me! Together we will make this world a better place! Wishing you good health, success and happiness! Thank you very much!

      @creationholic101@creationholic1019 ай бұрын

    • As a 37yo frenchman, I keep everything in several toolboxes: one for screws, screwdrivers, nails, hammers, drill bits, and an other one for all electrical, mechanical and plumbering stuff (wrenches/ratchets, soldering irons, electric tape, pliers...), a 3rd one for all that doesn't fit in the 2nd one, and all the other boxes are for my powertools (from drill to impact wrench).

      @Jean-Denis_R_R_Loret@Jean-Denis_R_R_Loret8 ай бұрын

  • 오~ 전기 작업 개꿀팁!

    @jhkim5305@jhkim53055 ай бұрын

    • I'm glad you enjoyed this project! Feel free to connect with other viewers in the comments section and share your results. It's always inspiring to see what everyone creates

      @creationholic101@creationholic1015 ай бұрын

  • 👌 Good sir.

    @vijaytoraskar4590@vijaytoraskar45908 ай бұрын

    • Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1018 ай бұрын

  • very good ❤❤❤

    @5-MinuteCreative-IQ@5-MinuteCreative-IQ10 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic10110 ай бұрын

  • Bravo bravo.

    @lelloaversa3108@lelloaversa31089 ай бұрын

    • "Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things! "

      @creationholic101@creationholic1019 ай бұрын

  • 電線不要纏繞會產生電感效應，固定電線要用壓接端子

    @chenweiming5628@chenweiming56287 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1016 ай бұрын

  • Very cool stuff thank u

    @bsb770@bsb7703 ай бұрын

    • Glad you like them!

      @creationholic101@creationholic1013 ай бұрын

  • Probing the light at 6:20 seems very dangerous as you are dealing with mains voltages without much protection.

    @saddle1940@saddle19409 ай бұрын

    • Yes.. terrible

      @marcsiegel3358@marcsiegel33589 ай бұрын

    • I used safety protection and my body did not come into contact with the ground

      @creationholic101@creationholic1017 ай бұрын

  • Amazing ideas bro

    @TechnicalSanaullah@TechnicalSanaullah10 ай бұрын

    • Thanks a lot

      @creationholic101@creationholic1019 ай бұрын

    • Danke, Schwester

      @ernstlessau8208@ernstlessau82089 ай бұрын

  • I haven't tried #4 , so I cant really say it won't work. but in theory , it shouldn't . because, not only are you cutting down on the operating voltage by 1.5 volts, using one battery, but then by using a pencil lead, which has electrical resistance, you are cutting the already halved voltage down even further. But if your device used AA you can use a AAA by putting a small ball of aluminum foil on the flat end of the AA battery. and it will work. but you might have to pack a little paper between the batteries so they wont move around and lose connection . AAA , AA and D sized batteries are very close to the same voltage just different sizes. to fit the battery compartment, and size of the device.

    @GothGuy885@GothGuy88526 күн бұрын

    • I use it in case I can't buy a replacement

      @creationholic101@creationholic10121 күн бұрын

  • Very good

    @user-le5jh9xq1m@user-le5jh9xq1m8 ай бұрын

    • Thanks

      @creationholic101@creationholic1018 ай бұрын

  • Step 4.....JUST USE THAT EMPTY BATTERY !!

    @kotorinest@kotorinest9 ай бұрын

    • I tried it and found it very good

      @creationholic101@creationholic1017 ай бұрын

  • Good idea 👍👍 Love from India ❤️❤️

    @Iammoolniwasi@Iammoolniwasi6 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic1016 ай бұрын

  • شكرا لكم . الحيلة الأخيرة ماذا بعد ثقب القارورة وتثبيتها بالجدار ؟

    @mhmdelsayed9121@mhmdelsayed91219 ай бұрын

    • Hello! thanks for your recommendation. Wish you all the best!

      @creationholic101@creationholic1019 ай бұрын

  • De l'Algérie 👌👌👍🇩🇿

    @zahret_elkoronfol@zahret_elkoronfol10 ай бұрын

    • Welcome to Creation Holic channel! Hope you have a good time while watching the video!

      @creationholic101@creationholic10110 ай бұрын

  • Полезно. 👍

    @user-vo6il1si4w@user-vo6il1si4w9 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1019 ай бұрын

    • Нет

      @jafionfirst6970@jafionfirst6970Ай бұрын

  • The first one only works because they removed the wire opposite the way they put it on. If the pipe had installed over a straight wire this would not have worked.

    @brownro214@brownro21426 күн бұрын

  • #6 the gentle pull makes a huge difference.

    @XB10001@XB100013 ай бұрын

    • Thank you for watching

      @creationholic101@creationholic1013 ай бұрын

  • Số 1 có nguyên tắc là gì nhỉ?

    @longpham5025@longpham502526 күн бұрын

  • your tricks are amazing

    @Alex-Tips@Alex-Tips10 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic10110 ай бұрын

  • Two things that surprise me: European plugs don't have cable clamps, and every household apparently has two different sizes of heat-shrink tubing lying around, and a heat gun, soldering iron and solder, but no proper co-ax connectors.

    @timf-tinkering@timf-tinkering3 ай бұрын

  • ❤

    @user-zp1sk2hj4u@user-zp1sk2hj4u8 ай бұрын

  • Начинает видео с застрявшей вилки, которую видели ещё в 2018 году. Ну не бывает такого, чтобы вилка случайно попала в такое узкое место.

    @FedorKalashnikov1911@FedorKalashnikov19115 күн бұрын

  • Very good.🙏❤️🙏❤️🙏

    @mohammadalipasargad@mohammadalipasargad5 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic1015 ай бұрын

  • superb

    @vinodtak9943@vinodtak99439 ай бұрын

    • "Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things! "

      @creationholic101@creationholic1019 ай бұрын

  • 😊ดีมากครับ ทำให้ทราบวิธีที่มีประโยชน์ แต่ข้อ 4 มีใหม่ 1 ก้อน ก็ใส่ไป ใช้งานได้ปกติแค่หมดเร็ว ข้อสุดท้าย ดีครับเพราะเหมาะกับช่างก่อสร้าง ช่างไฟ ช่างปะปา โดยเฉพาะถูกจ้างให้ไปทำตอนมีผู้อาศัยแล้ว ไม่ใช่บ้านใหม่ จะได้สะอาด😊

    @Sorn_4427@Sorn_44277 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1016 ай бұрын

  • Bei der Aktion mit den 2 Adern in dem Stecker, da gehören Ader-Endhülsen über die Kupferadern!!!

    @sabruwa@sabruwa8 ай бұрын

    • Thank you for your comment. Wish you have a nice day!

      @creationholic101@creationholic1018 ай бұрын

  • 0:37 Das ist wirklich meisterhaft, eine Litze ohne Endhülse verklemmen. 3:21 Ich weiß jetzt nicht, wieso der Hersteller zwei Batterien benutzt, wenn doch eine reicht. Wieso 3 Volt, wenn das Gerät mit 1.5 Volt auch funktioniert.

    @lutsifer5847@lutsifer58479 ай бұрын

    • Thank you for sharing your feedback and expressing your perspective

      @creationholic101@creationholic1019 ай бұрын

  • Good luck

    @AlirezaRezaei7070@AlirezaRezaei70709 ай бұрын

    • "Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things! "

      @creationholic101@creationholic1019 ай бұрын

  • Gostei do vídeo

    @edisonjesus4130@edisonjesus41306 ай бұрын

    • "Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things! "

      @creationholic101@creationholic1016 ай бұрын

  • good job..

    @Wal___eedz41@Wal___eedz412 ай бұрын

    • Thank you! Cheers!

      @creationholic101@creationholic1012 ай бұрын

  • 2,3,6,9번은 유지보수 기술로 좋은 팁.

    @asomine@asomine2 ай бұрын

    • Glad you like them!

      @creationholic101@creationholic1012 ай бұрын

  • ❤❤❤

    @mohammadshahriar4670@mohammadshahriar46709 ай бұрын

    • 🍀☘☘😘😘😘😚😚😚

      @creationholic101@creationholic1019 ай бұрын

  • Спасибо

    @alexrus1980@alexrus19806 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your support

      @creationholic101@creationholic1016 ай бұрын

  • You can not join coax cable, for every joint you make there is a 3 dB loss on the cable.

    @reonhenning3738@reonhenning37383 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1013 ай бұрын

  • Мм... Обожаю. Провод, который надо показать, что плохо закреплëн выдернул с видимым услием, а те, которые, типа, норм, те так... Слегка потряс из стороны в сторону. Ну, показал, ну молодец... Нет, безусловно, чем больше площадь провода, которая придавливается, тем лучше он будет держаться, но показывать это так убого ещё постараться надо.

    @yok-1123@yok-11232 ай бұрын

    • Thank you for watching

      @creationholic101@creationholic1012 ай бұрын

    • Он ещё и не правильно его посадил

      @jafionfirst6970@jafionfirst6970Ай бұрын

  • Indonesia,west java,karawang,cikampek,cikampek timur, cijalu, kebon kembang,

    @stoneofsky@stoneofsky9 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your support

      @creationholic101@creationholic1019 ай бұрын

  • Bro number 5 is straight up illegal and will potentially kill some one

    @iva00005@iva000059 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1019 ай бұрын

  • I'm from Indonesia

    @brlinrainf@brlinrainf9 ай бұрын

    • Welcome to Creation Holic channel! Hope you have a good time while watching the video

      @creationholic101@creationholic1019 ай бұрын

  • Def not going to want to do the LED light fix, that increases the voltage drop across the rest of the LED's in the circuit, might overheat, or start a fire.

    @ripcdburnme@ripcdburnme9 ай бұрын

    • Thank you for sharing your feedback and expressing your perspective

      @creationholic101@creationholic1019 ай бұрын

    • on the first LED fix it works, i have fixed LEDs over my room and work table for like... 2 or 3 years already. But with a 2nd LED fix in a few months the bulb melts (tried it with an independant connection) ofc the 1st fix must be made properly, 1 option is like in the video and a 2nd option can be using string wires (thin as hair) to secure the soldering iron

      @Elias-jq1ss@Elias-jq1ss8 ай бұрын

    • Just add a resistor

      @lucascosta3922@lucascosta39222 ай бұрын

    • @@creationholic101Your fine, just make sure there is no bad noticeable side effects these are all nice.

      @The_real_germeny@The_real_germenyАй бұрын

    • Сколько раз так делал и ничего не случилось

      @vehicles7462@vehicles746213 сағат бұрын

  • I am more likely to have proper wire strippers than nail clippers.

    @Geoff_G@Geoff_G9 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1019 ай бұрын

  • Don't play with electricity.

    @20secondsclips@20secondsclips2 ай бұрын

  • #2 without ferrules is illegal in germany, for reasons

    @Poboot@Poboot9 ай бұрын

    • What are the reasons? 🤡🤡🤡🤡

      @tompsheridantsheridant7354@tompsheridantsheridant73549 ай бұрын

    • Insufficient contact area of the cross-section, damage to the individual strands, risk of fire

      @Poboot@Poboot9 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1017 ай бұрын

    • @@creationholic101 Please do not make videos about electrics as you do not have in-depth knowledge of imitating people and endangering their health and life. In Germany you would have received an injunction and paid a large fine.

      @Poboot@Poboot7 ай бұрын

  • 6:50 no it's wrong. you can't just connect the chain instead of replacing the dead LED element. This is a common mistake in all such video tutorials. Because it will increase the brightens due to raising of load to other LEDs, making them suffer more and very soon one or more will be dead too.

    @jbnrusnya_should_be_punished@jbnrusnya_should_be_punishedАй бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic101Ай бұрын

  • ये बलफ का होल्डर पसंद आया इसके बारे में कुछ कहें या वीडियो बनाए

    @Devendradixit125@Devendradixit1259 ай бұрын

    • Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1019 ай бұрын

  • Nice

    @mdmonirul7255@mdmonirul72556 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your support

      @creationholic101@creationholic1016 ай бұрын

  • #4 why would you want the extra resistance?

    @XB10001@XB100013 ай бұрын

    • it will be very useful if you haven't bought a new device yet

      @creationholic101@creationholic1013 ай бұрын

  • First wone belongs to the 7 wonders of the world

    @damjanavativec210@damjanavativec2108 ай бұрын

    • Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1018 ай бұрын

  • # 2👍

    @avap2677@avap26779 ай бұрын

    • 🍀☘☘😘😘😘😚😚😚

      @creationholic101@creationholic1019 ай бұрын

  • Uzun süre kullanmadığım Raks vantilatörümü açtığımda hıç dönmedi. Motoru söküp şaftı hem önden hem arkadan yağladım. Dönmeye başladı ancak ilk açılışta hızlı dönüp😅 sonra yavaş dönmeye başlıyor. Ne arızası olabilir.

    @ibrahimozbek222@ibrahimozbek2223 ай бұрын

    • You should reapply the lubricant a few more times

      @creationholic101@creationholic1013 ай бұрын

  • Відео дуже корисне,але не зрозуміла операція з пляшкою.

    @user-wi3iw3hl3i@user-wi3iw3hl3i9 ай бұрын

    • Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful

      @creationholic101@creationholic1019 ай бұрын

  • 💜💜💜💜💜

    @hermesarm2721@hermesarm27219 ай бұрын

    • 🍀☘☘😘😘😘😚😚😚

      @creationholic101@creationholic1019 ай бұрын

  • zu 2, auf die Aderenden gehören aber Aderendhülsen drauf. Das sollten Sie aber wissen.

    @uranus348@uranus3488 ай бұрын

    • Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!

      @creationholic101@creationholic1018 ай бұрын

    • Diese verwendeten Stecker gehören in den Müll!

      @marcsiegel3358@marcsiegel33587 ай бұрын

  • Nunber 8 is the greatest joke. New cable or the correct f connector😅😅 2.80€

    @thomasschafer7268@thomasschafer72688 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1017 ай бұрын

  • A quien le ha pasado el número 1????

    @sebastianaguilera2410@sebastianaguilera24102 ай бұрын

    • Thank you for watching

      @creationholic101@creationholic1012 ай бұрын

  • Что за бред с карандашиком? Ничего, что схема и фотодиод рассчитаны на 3V?

    @user-mu8ov5yn8m@user-mu8ov5yn8m9 ай бұрын

    • I have used it and find it quite good

      @creationholic101@creationholic1017 ай бұрын

  • Да постоянно тески есть спать, смешно😂😂😂😂😂

    @user-sc6mo3bb7s@user-sc6mo3bb7s4 ай бұрын

    • Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1014 ай бұрын

  • дякую

    @Darya_Kravchenko@Darya_Kravchenko9 ай бұрын

    • Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1019 ай бұрын

  • This guy lives with stone age peoples

    @yametekudasai2273@yametekudasai22732 ай бұрын

    • I'm sorry to hear that the video didn't meet your expectations. I appreciate you bringing this to my attention

      @creationholic101@creationholic1012 ай бұрын

  • 2:11-А почему изолента не синяя?!?

    @STANISLAV_NIYAZOV@STANISLAV_NIYAZOV9 ай бұрын

    • TOC issues... 😮😮

      @Elias-jq1ss@Elias-jq1ss8 ай бұрын

  • Azərbaycandanam

    @balasasadov640@balasasadov6409 ай бұрын

    • Hello! welcome to Creation Holic channel. I am very happy to read your comment. Wish you have a nice day!

      @creationholic101@creationholic1019 ай бұрын

  • quella del telecomanda non è vera

    @enricodomenicobossi9594@enricodomenicobossi95949 ай бұрын

    • I tried it and found it very good

      @creationholic101@creationholic1017 ай бұрын

  • Clearly has never worked with cables and electricity

    @lumyre1706@lumyre17069 ай бұрын

    • Thank you for sharing your feedback and expressing your perspective

      @creationholic101@creationholic1019 ай бұрын

    • @@creationholic101 aaawww

      @lumyre1706@lumyre17069 ай бұрын

  • Номер 6. Все и так закручивают провод вокруг болта. Никто прямой провод не соединяет.

    @Hirurg_XX@Hirurg_XX4 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1014 ай бұрын

  • Bro this is just five minute crafts but smarter

    @makhisworld1969@makhisworld1969Ай бұрын

    • Thank you for watching

      @creationholic101@creationholic10129 күн бұрын

  • Ok everyone this is not how you fix electrical issues

    @tjmilligan1730@tjmilligan173029 күн бұрын

    • Please try and feel

      @creationholic101@creationholic10124 күн бұрын

  • I didn't understand the use of#9

    @fmitsinc9146@fmitsinc91469 ай бұрын

    • sawdust collection when drilling

      @bullpuppy7455@bullpuppy74558 ай бұрын

    • thanks you

      @creationholic101@creationholic1017 ай бұрын

  • Din Romania

    @PlicIulius@PlicIulius8 ай бұрын

    • Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best

      @creationholic101@creationholic1018 ай бұрын

  • З лампочкой таке не проходить пару разів робив перегоряє все одно

    @user-dd6ds9dd4v@user-dd6ds9dd4v4 ай бұрын

  • 3:30 your edits aren't smooth😅

    @GavinSkibz@GavinSkibz9 ай бұрын

    • Hello! thanks for your comment. Wish you all the best!

      @creationholic101@creationholic1019 ай бұрын

  • Не хочу обидеть, но многие из вариантов можно сделать проще и лучше😅 Лучше начните снимать обучающие электронике видео, а не старые лайфхаки😅

    @Aminael_00@Aminael_00Ай бұрын

    • I'm sorry to hear that the video didn't meet your expectations. I appreciate you bringing this to my attention

      @creationholic101@creationholic10129 күн бұрын

  • чё за бред с пультом, во первых от 1.5в он скорее всего даже не заработает или будет очень слабый сигнал, а во вторых грифель не проводит ток Лампочка с коротышом место диода проработает от силы неделю, потом сгорит ещё один диод, т.к. на все оставшиеся диоды будет подано больше тока

    @MARK2580@MARK258029 күн бұрын

    • it works very well, try it and feel it

      @creationholic101@creationholic10124 күн бұрын
KZhead