5 Tips and Tricks to Improve Flux Core Welding
I've said it before but this video I go into more detail on why you DON'T need the nozzle when flux core welding.
Tips and Tricks to making your Flux Cored Arc Welding (FCAW) or gasless MIG and MIG welds looking AWESOME!
Threaded Flux Core Nozzle: amzn.to/3MXzKWb
Slip on Nozzle: www.harborfreight.com/gasless...
Spatter Spray- amzn.to/403sStH
Nozzle gel- amzn.to/3ZLqNmg
Helmet- amzn.to/3JBQfVO
Gloves- amzn.to/3Jbw1kd
Angle Grinder- amzn.to/3mJe2Kt
Horizontal Band Saw: amzn.to/3JgdG5t
Magnets- amzn.to/3lcr5DQ
Clamps- amzn.to/3YF1xg9
Welding pliers- amzn.to/3Ta4lks
Wire Brush- amzn.to/3YOVuWu
Chipping Hammer- amzn.to/3Fp357h
1- Remove the Nozzle 0:07
2- Helmet 1:31
3- Settings 2:15
4- Keep It Simple 3:30
5- Nozzle Gel 3:58
#fluxcorewelding #howtoweld #harborfreighttools #diy
Happy Welding with out the spatter! Spatter Spray- amzn.to/403sStH Nozzle gel- amzn.to/3ZLqNmg
Love how you break it down so easy
Right on, thanks!
Thanks for the tips - Chris
Any time!
Put a heavy duty rubber band over the voltage and speed knob that way all you have to adjust is one
I'll have to try that!
I did a thing on welding without a nozzle in my tips and tricks. Try to cover the threads using an old diffuser insulator. Or get a piece that covers it like you showed, you don't have to but... I save money in brass diffusers this way not just the gas hole. The threads get ruined fast if you arc them off your product, just setting it down can bump the trigger or still have some amps in it to arc im sure you've seen it. I've made a few mistakes. Imo that's one I don't forget when you need it on a holiday weekend and the stores are closed.😅
Great advice 👍
Thanks for watching!
Is that a Miller Digital Infinity? How do you like it?
It is, I actually have the elite as well. I like the infinity better. It's slightly bigger. If you can find one with the 2.0 clear lens it's worth the extra.
I tried flux core for the first time a few days back it's weird first time around...dragging, no shroud, .if the slag came off like stick does I'd probably use it more .
When you get into thicker material or higher amperage it does peel off, almost like stick does!
I started a few weeks ago.... doing ok however my machine is super hard to find a decent setting and comes with no "suggested" sticker lol
What machine do you have? One suggestion is you can actually time the wire speed at the low, middle, and high settings and take that speed to online charts for a starting point.
@@-DIYPRO- "TP TOOLS" Lol, I'm in Thailand & everything is backwards, Arc sticks don't have numbers. Metric & Imperial are used in EVERYTHING so IDK if IP/M or MM/m lol. Even some steel at the hardware store is in mm thickness yet some is inch lol. I guess I can do the 6 second measurement & try that. So far for 2.6mm steel I've used 270-340 IPM? and about 16.5v. Feed seems low but cranking it seems to get too hot and the puddle bubbles. Could be the wire too as some I've noticed states + and some - lol yet I was assuming 99% is EN- lol. Simple tasks here are near impossible!
Do the feed and power knobs always move in tandem? IOW do you always move them to the same position? Both at 3:00 for example. - Thx! Eric.
@@gardenfork nope but I can try it lol
Sometimes they might line up but not always. Depends on the machine as well.
*Promo SM* 🏃