🛩️ Fimi Manta VTOL - How I Got Mine To Fly Properly On INAV
A quick video showing how I got my Fimi Manta VTOL rc plane flying decent with INAV 7.1 firmware.
Want to help me keep making videos? www.buymeacoffee.com/gizfpv
If you want to try my programming/settings, below is a DIFF file you can download and then upload to your Manta. Make sure that first you flash your Manta with INAV 7.1 firmware, using the target MATEKF405TE_SD. Note that unless your Manta build is identical to mine, you may need to tweak some settings. You might also need to manually adjust the linkages on your servos. Use the below DIFF file with caution!
drive.google.com/file/d/1hL2E...
00:00 Introduction
1:14 Slowing down the tilt servos
3:19 Autotune
4:06 Changed the flight modes
6:46 Fixing corrupt sensor data
10:24 First flight and RTH test
17:08 Second flight
19:19 Conclusion
YES..good information to use MixerTab for TilRotorSpeed and tiltservo positions to have "TransitionDone" smoother ❤
Now let’s try tail sitter in inav!
Thank you so much for demystifying this model. And, thank you for the files! Great job!
That's an impressive improvement. Thanks for sharing your various tweaks 🙂
Great insights Giz. It flies, "it's not stupid!" A design matter that stands out is the motor-tilt hinge-line is not aligned with the thrust line of the motor (1:35). If you look at the HeeWing VTOL (and other tilt designs), the motor mount and thrust-line are centre aligned with the tilt pivot axis. The Fimi Manta pivots from the top of the motor mount (1:35), so servo torque applied will be non-linear. When the tilt servos where moving faster, they also had to created additional unwanted torque from gyroscopic effects of the spinning propeller. (worse on transition from hover to wing flight due to higher motor rpm) For fixed-wing mode, it may be interesting to experiment with a tiny mix between elevon servo and the motor tilt servo. This could be a way to increase roll rate, and pitch response.
Good point about thrust line and pivot point....A schoolboy error by Fimi....🤔😳😏🇬🇧
Awesome flying, dude! 😃 Thanks a bunch for all the tips for setting it up! Stay safe there with your family! 🖖😊
Very good, baby steps paid off. I use Horizon mode quite often in iNav as it gives full control of the flight surfaces to full deflection regardless of tune. The wobbling however is caused by Horizon Mode, so its a double edged sword. Once tuned, flying in Acro mode or gyro rate Mode if you prefer will give a much smoother flight overall. Yeah, position hold can only be used once its hovering, not before. Great progress eh?...🤔😳😏😀🇬🇧
This is wildly impressive. I’m gonna either use a donor plane or straight build my own plane very soon.
Excellent Giz, been waiting for this. Many thanks
If you wanna give Inav a go on your Manta, I've put in link in my video description to download my DIFF. Will give you a head start on the programming :)
@@gizfpv Got it. Excellent
the video I was waiting for... Thanks! will you share the dump cli parameters? I want to test inav on my manta with your setup
I've added a link to the video description :)
Beautiful
Wow! Amazing job ... My respect for the improvment and the final result. Many Thanks for share!
Awesome!
Nice that you got it working with INAV. If mine don’t fly well in ardupilot at least I got back up 😅. Btw you gave me a good idea with blu tack👍
I changed the mode in Ardupilot from QStab to QLoiter. Which has two big advantages. First off, it will not arm until you have satellite lock and secondly, it is much more stable and hovers reasonably well in this mode. A lot of folks get in trouble with the stock setup and take off not realizing that they don't have satellite lock. Then when they do RTH, it will fly away into never never land.
@@raptr49 this is mine:kzhead.infoZ4g_wTjkYk8?si=GKQf2FMeksmjcE3T It flies pretty well. For the time being, I will stick with Ardupilot.
Nice.
If you limit the transition angle to 45 degrees or higher, the roll/yaw oscillation is greatly reduced. I don't want to slow my tilt servos, because the transition from 45 to forward flight has a ludicrous pitch up, as the rear motor just turns off while the tilt motors are still pointed upwards. It would be great if the rear motor turned off slowly at the final transition instead of instantly. I do the whole transition in Acro, no self leveling needed.
Now u need a servo on your roll switch for a camera tilt function so u can see better
Great video, I'm still hesitant to switch to INAV. In the VTOL position, the engine mount is vertical with the engines horizontal ? On the original version, the engines are tilted slightly towards the rear.
Thanks for the diff, got it set up, just one question how far should the throw travel on the wing servos end points be and how high should the rates be? my rates are at 100 percent. not sure if the diff you gave records these settings? Cheers.
i'm totally buying one of these next time they go below $110 USD for the PNP+FC version
14:38 it has three motors, instead of quad I think better call it tricopter, multirotor, multicopter
Would you comment on how it performs in INAV versus ArduPilot? Also, how did you connect the compass? I bought the RTH version and the two leads for the compass are not connected. Where exactly do they connect on the flight controller. Thanks
😱 OMG. I have so many questions. Did you use the FC version? Would you make a video of your conversion? Will you share your CLI dump. I been trying to get mine to fly with Arduplane with absolutely no luck at all. This looks like an awesome alternative.
Yeah man, using the stock manta with the stock electronics and the stock fc. Check the video description, Ive uploaded a cli dump there for people to copy 😊
Great Vid! Could you please provide the 3d print for the gps mount? Would help a lot. Thanks!
www.thingiverse.com/thing:6610586
Hi i would like your cli dump too please! mine has been a pain with the stock ardupilot, cannot get osd working properly with 03 air unit, too slow getting gps fix no matter what gps module you use or where you mount it.
I've added a link to the video description :)
@@gizfpv Nice!
Nice! Dump file please. I'm thinking about getting one
I've added a link to the video description :)
Awesome!
what vtol would you raccomend to start?
Probably the Heewing T1 VTOL, as its a very well designed and build aircraft. Although if you're inexperienced and feel like you're likely to crash a lot, get the Manta as its cheaper lol
Can you provide the dump file for us please 😊
I've added a link to the video description :)
1st view!
Bad ass!!
It was very good, you are doing a good job updating Fimi Manta at Inav. Congratulations!!! I am waiting to fly mine too, I would like to ask you to look at your email if it is possible, the click that passed me has missed a profile! 😅
Turns out that a CLI dump doesn't work for a VTOL. Instead I think you need to do upload a DIFF ALL file instead. Check the video description, I've added a link to download the DIFF all file. Hopefully it'll work!
@@gizfpv I managed to solve by copying the profile that was missing from the Github page and putting it together with what sent me, I did not test for not being able to find a place to fly, but thanks for sharing with me and now putting the link, sure it helped me and will help me more people. Thanks!!!