Brandon, this is the video I’ve been waiting for!!! I have 2 115hp Johnsons and 4 85hp this is what I’ve needed!!!!!
@MrCharles5047 ай бұрын
You made a wonderful job ! 👏 Well done Brandon !!! 👍
@adwyfriangliga84837 ай бұрын
Sounded really good on that first fire. Nice work keeping it running.
@jdub9766 ай бұрын
My last boat had a Johnson 90HP V4 very much like yours. It was cranky to start just like yours. Very interesting to see one being striped down and repaired. Nice job.
@iantyler40457 ай бұрын
In this engines , hone that cilínder and you could install only that piston oversized to .20 or .30 ,as long as the pistons weight the same you’ll be ok with only doing that cilinder…. Also make sure to gap those rings to that cilinder meeting the specs in that way you won’t be guessing the outcome.I used to be an omc mechanic trained in the factory …..I also done this and it comes out reliable.
@franciskreig33967 ай бұрын
Thanks for that info! Can I have your email ? Would love to have your input when I replace my piston in my 1980 115hp
@travist78456 ай бұрын
Man, your are genius, many thanks. I am about to rebuilt my 1985 OMC 115hp soon. This video help alots.
@TanNguyen-zz5hs4 ай бұрын
Really like that ring test with the light to see the gap, was was thinking ah just chuck a new piston in it and send it until you did that. P.s where’s the cash tote gone?! That used to make me chuckle seeing dollars thrown into that
@jamesread117 ай бұрын
Have the same exact motor took it apart today someone put the power head bottom gasket on backwards and it was leaking water.Good video!
@tallman2818307 ай бұрын
I have an old 1987 V4 90hp VRO Cross Flow? (I think) with all new parts, rebored, honed, and ready to reassemble. Been sitting in 25 boxes under my bench for a few years now waiting. I'm going to get at it soon. These videos are excellent confidence builders!! Thank you for sharing.
@rodwinsor41456 ай бұрын
Your a genius.. Thanks for this. What a lovely sound. A job well done
@rocketroy4692 ай бұрын
By the way sir could you tell me what size is the flywheel nut on that 115 horsepower v4
@rocketroy4692 ай бұрын
The best money can buy 👌
@dsciarrino36637 ай бұрын
Many thanks for the rebuild video. I was glad about the overall result on rebuilding my v4 crossflow but getting accurate information for certain things not answered in factory service manual was a royal pain in the neck. I think a 3/4" brass barbed fitting that you can get at Home Depot/Lowes works well as a piston wrist pin clip installer tool on those pistons. It's possible to get the OEM clips without that tool, it is a NIGHTMARE on those Wiseco pistons for the wrist pin clips. That connecting rod tool I wish was a 1/4 of the price. Had to align the rod caps using a pick or throw away the used rods that wouldn't line up because I didn't have the tool to compress the ends to align.
@havocsquad17 ай бұрын
Awesome job.
@paulcox50077 ай бұрын
Great video! Wish this was a Evin 25 HP, I have one of those, and want to rebuild it.
@bginvestor1017 ай бұрын
Your good bud..Real good....
@woody951246 ай бұрын
highly recommend using an engine or powerhead stand when installing pistons into a v4 or v6 crossflow. its not easy getting them in straight on a bench, and the block needs to be tilted to get it parallel. takes 5x longer and you end up dragging the rod over the fresh cylinder bores as demonstrated.
@ct17627 ай бұрын
Excellent video
@williambrooks45857 ай бұрын
Good video Brandon. What did the final tally of parts and repairs cost you? Got a couple 1980's 115hp that i want to hone and put new rings into.Can you do a video of the settings, linkage and sync, timing?
@troybenko7437 ай бұрын
Nice job! Above my pay grade but have a 78 Evinrude 115 that hasn’t been started in 10 years. Will check the compression and if bad will just trash it cause boat is not that good either.
@Berkner803 ай бұрын
where are you located i would love to pick your brain about a 1980 85 HP evinrude i have btw great videos you are the only one i want to get info from about my outboards !
@user-uz6jp4if7e5 ай бұрын
I bought a v4 and now I have 3 of them. Finish ed one partial rebuild. Enjoyed your video thanks!
@mattstoker83752 ай бұрын
Oh yeah, they duplicate. It's best not to get them wet or feed them after midnight.
@BrandonsGarage2 ай бұрын
Have you ever built your own water tubes? Tough to find. Also what kind of paint do you use. Thinking of powder coating but not sure.
@mattstoker83752 ай бұрын
I have a 95 115 that I’m rebuilding. Lost all my videos of the disassembly when phone was lost. This video is a life saver. Need additional video on shifting cables and shifter set up… wonder if I joined the patron would you be willing to to do that?
@tf338021 күн бұрын
Great job Brandon
@TimsWorkshopTJY7 ай бұрын
Enjoyed the video. I have rebuilt automotive engines and I’m curious. What purpose does that tool serve when installing the connecting rod caps? Can you install them without the tool? It looks really expensive. New subscriber. Thanks for the video.
@jimdrechsel36112 ай бұрын
What is the function of the bypass covers? I have had an engine block cracked on the outside of the bypass housing. Any ideas what may have caused this? Thanks again for a great video.
@jimdrechsel36112 ай бұрын
My 112 SPL has a VRO from factory, that looks like an aftermarket VRO delete kit
@just-a-waffle2 ай бұрын
I had to laugh at the coffee can thing. I still use one but for 10hp or smaller motors. Now that time is a factor with more motors to restore going to organize them so I can pick it up.
@TimsWorkshopTJY7 ай бұрын
Enjoyed that. We had some self-imposed rebuild rules in our shop.......... If it scored a cylinder wall and/or rolled a ring, we would always replace the thermostats, the water pump, and rebuild the carbs as part of the rebuild job. We also replaced the fuel pump. We didn't want a hot running engine and we didn't want a lean running engine. We were making an extra effort to eliminate what caused the problem to begin with. And, of course, we always checked to see if the heads got warped. More often than not, we planed the heads as a result. You usually never know what caused it. Ran hot? Why? Ran lean? Why? Total timing - is the stop adjustment loose? On and on........... Thanks for the video.
@mikedurhan99417 ай бұрын
Ron from Rons Marine believes the prop was too small. Which isn't a bad guess as it came with a pretty small aftermarket 4 blade.
@BrandonsGarage7 ай бұрын
I can see where that would do it, for sure. May have come off a pontoon and been put on a runabout. Thanks again.@@BrandonsGarage
@mikedurhan99417 ай бұрын
It looked like you put gasket sealer on the bolts too. Do you find that it helps with removing the bolts later if you did use it on the bolts? Thanks
@thecableguy11287 ай бұрын
Brandon, I am 79 to start with and just did what you did on a 1986 88hp SPL. This was new to me but after the rebuild, I am getting some hiccups and the idle screw is not coming back all the way even after Blaster and cleaning foam. I was thinking of adding a spring to bring the screw back to the stop for a better idle. What could be causing the infrequent hiccups on the hose water feed? jim
@jameshoffman11905 ай бұрын
Where is the best place to purchase complete engine rebuild kits
@terryrichardson14345 ай бұрын
The bubble back exhaust parts...are they compatible with the flat back engine blocks? I have a 100XP that's getting low on compression and these parts seem a no brainer to add while in there.
@user-vn7un4uu6g7 ай бұрын
Just a quick question if you don’t mind. How on Gods green earth do you keep up with all the nuts and bolts bolts and all the washers cotter pins etc?! Lol
@jeffbrummette162228 күн бұрын
Can you use a high temp silicone under the power head for a gasket?
@user-xe3id7xh9m6 ай бұрын
So I have a 1989 110 Johnson 2 stroke that came with a vro pump, and I replaced it with a regular aftermarket fuel pump, but do I need to remove the pulse limiter inline valve thingy?
@VapingSavesLives7 ай бұрын
Evinrude makes 112hp spl I have one, that has holeshot problems….Any suggestions would be appreciated
@americanmade81457 ай бұрын
Any idea what is the PSI after the rebuilt?
@mabo18117 ай бұрын
Great video I could change the spark plugs and maybe rebuild the carbs so I’m definitely not going to be a keyboard mechanic and point out what you are doing wrong 😅
@ktcarroll47237 ай бұрын
Cuál es el torque de las vielas y el crank
@Gperformance7775 ай бұрын
Buen trabajo amigo tengo un motor Johnson igual que ese quisiera saber si usted se dedica a este trabajo para arreglar mi motor con usted vivo en Miami florida
@El.explorador.2 ай бұрын
I've always been thinking that V-4 engines aren't best part of OMC outboards.( Unfortunately) this video didn't change my mind, althought Brandon made this job look so easy. Btw... My vintage Kawasaki outboard motor is a runner now😊, after sleeping some decades.
@minimibudjetti7 ай бұрын
Why do you not like the V4's? Whenever I see them torn down they look a heck of a lot like the V6's.
@mjodr7 ай бұрын
I got 1987 I will try to do one cilynder I have not done any like that before so my question is what dice should I order in Amazon hope you read my message- thanks for the video
@alejandrovargas93722 ай бұрын
What dice?
@BrandonsGarage2 ай бұрын
GReat video. Where can I purchase motor specific shop manuals? The one I have covers multiple years and engines. Need a specific manual for better detail and specs.
@terryrichardson14347 ай бұрын
Well, what year/HP is your engine? Or give me the model number
@BrandonsGarage7 ай бұрын
1994 Johnson 115 J115TLERC @@BrandonsGarage
@terryrichardson14347 ай бұрын
Brandon, any thoughts where to find one of these manuals.
@terryrichardson14346 ай бұрын
I would paint it black with Johnson white and orange and white stripes 😊😊
@larryperdue5087 ай бұрын
Are you interested in selling that motor???? If so how much would you want for it???
@DanVanDorn4 ай бұрын
From what I could see in the video, I probably would have just honed the cylinder wall, slapped in a new piston and rings and called it a day. Although I do have my own Kwik-Way boring bar, it takes all day to bore a cylinder because I only use it every couple of years for motorcycle restorations and I have to learn it all over again and its EASY to make a mistake.
@bobhamilton2987 ай бұрын
I've been thinking about getting one and trying it out. How hard is it?
@BrandonsGarage7 ай бұрын
Its not hard, but its easy to mess up. I have had a couple throw away cylinders because I don't use the boring bar enough. Not a good thing when boring cylinders on vintage engines! You can find these for just over $1000. I paid $3K for mine and it has not been cost effective as I don't use it often. But if you use one about once a month, it would be well worth it because you can do the job in a few hours once you familiarize yourself with it. Same with doing my own valve jobs.
@bobhamilton2986 ай бұрын
More good info to add to my knowledge bank when I inevitably have to do this. Shame you couldn't find a machine shop locally. Frustrating living here and never being able to find local businesses to do stuff.
@mjodr7 ай бұрын
Do the stats…killed my Johnson power head!!!
@raymondlantz92787 ай бұрын
am sure i've read in the book somewhere if one cylinder is bad you gotta rebore all 4. Especially after #1 clip the ring on a bad angle.
@fishawk907 ай бұрын
He reused all bolts probably gaskets lol
@chriscobb49397 ай бұрын
@chriscobb4939 hell yeah I did.
@BrandonsGarage7 ай бұрын
You must have read it backwards. 1 hole is fine by the book. As is reusing the bolts. They're not torque-to-yield so have no permanent deformation.
@paulmoir44527 ай бұрын
@@paulmoir4452 Reboring one hole is fine, but NEVER reuse the big end bolts.
@k.whiking43722 ай бұрын
@@k.whiking4372Not required on the old outboards I work on. I'd be a little surprised that it would matter much on a 2-stroke since, unlike a 4-stroke, the rod is always in compression.
@paulmoir44522 ай бұрын
I was an OMC tech from 74-86. When did the 115 get the bubble back? Used to be only the 135 and 140
@cchrisfish7737 ай бұрын
In 85 or 86 they changed from crank HP to prop HP. So the 140 became the 115 and the 115 became the 90. So this is similar to the old 140
@tylough23 күн бұрын
You do great job or this job is too hard for
@foudelnoreddine88623 ай бұрын
I can’t tell you how many engines I’ve rebuilt in my 38+ years of wrenching but that’s gotta be the fastest rebuild I’ve ever seen 😂😂 Glad to see you used a torque wrench 😂😂 An other great job 👍🏻
@ronaldjoyce73747 ай бұрын
Hello sir! I’m looking to upgrade the motor on my 17’ bass tracker. Currently it has a Johnson 40hp. So you happen to have anything larger and preferably with trim. What’s the best way to get ahold of you? Thanks!!
@clintdunning68416 ай бұрын
Well where are you located?
@BrandonsGarage6 ай бұрын
I’m in Flagstaff
@clintdunning68416 ай бұрын
Or is it possible to add a trim or tilt motor to my existing motor.
@clintdunning68415 ай бұрын
What's the average price to have an 60,70,75 hp Evinrude 2 stroke rebuilt ?
@Robin-by7nd4 ай бұрын
2000-3000 I would imagine
@BrandonsGarage4 ай бұрын
Can’t believe they didn’t clean the block!😮 I think I’d rather rebuild an sbc 😂
@davidroberts36926 ай бұрын
That thing came apart almost to easy.
@jimdoughty30057 ай бұрын
I'd dye it up, and hone it a second. See what it looks like,
@jamest.50016 ай бұрын
Putting in a 15, 30, or a 40 over size piston
@rreevesb34 ай бұрын
That was a 30.
@BrandonsGarage4 ай бұрын
Where you located at?
@michaelmonday5230Ай бұрын
Arizona, you?
@BrandonsGarageАй бұрын
@@BrandonsGarage florida
@michaelmonday5230Ай бұрын
i thought it was only the 140 hp that had the extra manifold between the cylinders the 115 hp engines i have seen only had a flat plate not the ball that contains the manifold
@ottoolsen95607 ай бұрын
Both types in a 115. Early ones had flat-back; later went to bubble back. Flat-backs are better, more durable engines.
@mikedurhan99417 ай бұрын
How many hours did that take you
@timburnett67297 ай бұрын
Months. I started it just before summer. Ron's wife fell ill, so he was a little delayed being able to accept the powerhead, then delays on parts, then I got busy with customer projects; and the delays just kept coming. I forgot to order spark plugs, and that delayed the video another week,
@BrandonsGarage7 ай бұрын
53 minutes. 😁
@dougaranda61877 ай бұрын
What is a VRO pump?
@jeffbrummette16227 ай бұрын
Mixes oil with fuel right before sending to the carbs. AKA the opposite of premix. Mine failed and I went regular pulse pump and premix.
@mjodr7 ай бұрын
VRO = Variable Ratio Oil. It mixes the oil & fuel together before sending it to the carburetors. At idle it mixes at between 150:1 & 100:1 ratio depending on years to prevent fouled plugs from excess idling. WOT it would mix around 50:1 ratio.
@t-bone437 ай бұрын
Very Rarely Operates
@k.whiking43722 ай бұрын
Why would you only bore 1 cylinder over and not all 4 never have I seen that and I've built dozens of motors
@kimgransden1426 ай бұрын
Money. $120ish for each cylinder + $100 for the piston. Good way to save $660 + tax on a low hour engine within spec. Now, granted, it might be a little cheaper than that; I did buy new rings, and I did pay for the honing, so it's probably closer to a $500 savings.
@BrandonsGarage6 ай бұрын
But it throws the balance out that 1 piston weighs more and will put more vibration in the motor it will eventually break again
@kimgransden1426 ай бұрын
I ran 100 hp commercial model evinrudes before honda 4 stroke took over the commercial crabbing industry after around 1000 hours on evinrudes they were junk & it was always the same issue rings sticking & this is what I could not understand why wouldn't they engineer a better design they knew exactly where their engines would fail & never made improvements also that primer injection gadget is a worthless pos
Brandon, this is the video I’ve been waiting for!!! I have 2 115hp Johnsons and 4 85hp this is what I’ve needed!!!!!
You made a wonderful job ! 👏 Well done Brandon !!! 👍
Sounded really good on that first fire. Nice work keeping it running.
My last boat had a Johnson 90HP V4 very much like yours. It was cranky to start just like yours. Very interesting to see one being striped down and repaired. Nice job.
In this engines , hone that cilínder and you could install only that piston oversized to .20 or .30 ,as long as the pistons weight the same you’ll be ok with only doing that cilinder…. Also make sure to gap those rings to that cilinder meeting the specs in that way you won’t be guessing the outcome.I used to be an omc mechanic trained in the factory …..I also done this and it comes out reliable.
Thanks for that info! Can I have your email ? Would love to have your input when I replace my piston in my 1980 115hp
Man, your are genius, many thanks. I am about to rebuilt my 1985 OMC 115hp soon. This video help alots.
Really like that ring test with the light to see the gap, was was thinking ah just chuck a new piston in it and send it until you did that. P.s where’s the cash tote gone?! That used to make me chuckle seeing dollars thrown into that
Have the same exact motor took it apart today someone put the power head bottom gasket on backwards and it was leaking water.Good video!
I have an old 1987 V4 90hp VRO Cross Flow? (I think) with all new parts, rebored, honed, and ready to reassemble. Been sitting in 25 boxes under my bench for a few years now waiting. I'm going to get at it soon. These videos are excellent confidence builders!! Thank you for sharing.
Your a genius.. Thanks for this. What a lovely sound. A job well done
By the way sir could you tell me what size is the flywheel nut on that 115 horsepower v4
The best money can buy 👌
Many thanks for the rebuild video. I was glad about the overall result on rebuilding my v4 crossflow but getting accurate information for certain things not answered in factory service manual was a royal pain in the neck. I think a 3/4" brass barbed fitting that you can get at Home Depot/Lowes works well as a piston wrist pin clip installer tool on those pistons. It's possible to get the OEM clips without that tool, it is a NIGHTMARE on those Wiseco pistons for the wrist pin clips. That connecting rod tool I wish was a 1/4 of the price. Had to align the rod caps using a pick or throw away the used rods that wouldn't line up because I didn't have the tool to compress the ends to align.
Awesome job.
Great video! Wish this was a Evin 25 HP, I have one of those, and want to rebuild it.
Your good bud..Real good....
highly recommend using an engine or powerhead stand when installing pistons into a v4 or v6 crossflow. its not easy getting them in straight on a bench, and the block needs to be tilted to get it parallel. takes 5x longer and you end up dragging the rod over the fresh cylinder bores as demonstrated.
Excellent video
Good video Brandon. What did the final tally of parts and repairs cost you? Got a couple 1980's 115hp that i want to hone and put new rings into.Can you do a video of the settings, linkage and sync, timing?
Nice job! Above my pay grade but have a 78 Evinrude 115 that hasn’t been started in 10 years. Will check the compression and if bad will just trash it cause boat is not that good either.
where are you located i would love to pick your brain about a 1980 85 HP evinrude i have btw great videos you are the only one i want to get info from about my outboards !
I bought a v4 and now I have 3 of them. Finish ed one partial rebuild. Enjoyed your video thanks!
Oh yeah, they duplicate. It's best not to get them wet or feed them after midnight.
Have you ever built your own water tubes? Tough to find. Also what kind of paint do you use. Thinking of powder coating but not sure.
I have a 95 115 that I’m rebuilding. Lost all my videos of the disassembly when phone was lost. This video is a life saver. Need additional video on shifting cables and shifter set up… wonder if I joined the patron would you be willing to to do that?
Great job Brandon
Enjoyed the video. I have rebuilt automotive engines and I’m curious. What purpose does that tool serve when installing the connecting rod caps? Can you install them without the tool? It looks really expensive. New subscriber. Thanks for the video.
What is the function of the bypass covers? I have had an engine block cracked on the outside of the bypass housing. Any ideas what may have caused this? Thanks again for a great video.
My 112 SPL has a VRO from factory, that looks like an aftermarket VRO delete kit
I had to laugh at the coffee can thing. I still use one but for 10hp or smaller motors. Now that time is a factor with more motors to restore going to organize them so I can pick it up.
Enjoyed that. We had some self-imposed rebuild rules in our shop.......... If it scored a cylinder wall and/or rolled a ring, we would always replace the thermostats, the water pump, and rebuild the carbs as part of the rebuild job. We also replaced the fuel pump. We didn't want a hot running engine and we didn't want a lean running engine. We were making an extra effort to eliminate what caused the problem to begin with. And, of course, we always checked to see if the heads got warped. More often than not, we planed the heads as a result. You usually never know what caused it. Ran hot? Why? Ran lean? Why? Total timing - is the stop adjustment loose? On and on........... Thanks for the video.
Ron from Rons Marine believes the prop was too small. Which isn't a bad guess as it came with a pretty small aftermarket 4 blade.
I can see where that would do it, for sure. May have come off a pontoon and been put on a runabout. Thanks again.@@BrandonsGarage
It looked like you put gasket sealer on the bolts too. Do you find that it helps with removing the bolts later if you did use it on the bolts? Thanks
Brandon, I am 79 to start with and just did what you did on a 1986 88hp SPL. This was new to me but after the rebuild, I am getting some hiccups and the idle screw is not coming back all the way even after Blaster and cleaning foam. I was thinking of adding a spring to bring the screw back to the stop for a better idle. What could be causing the infrequent hiccups on the hose water feed? jim
Where is the best place to purchase complete engine rebuild kits
The bubble back exhaust parts...are they compatible with the flat back engine blocks? I have a 100XP that's getting low on compression and these parts seem a no brainer to add while in there.
Just a quick question if you don’t mind. How on Gods green earth do you keep up with all the nuts and bolts bolts and all the washers cotter pins etc?! Lol
Can you use a high temp silicone under the power head for a gasket?
So I have a 1989 110 Johnson 2 stroke that came with a vro pump, and I replaced it with a regular aftermarket fuel pump, but do I need to remove the pulse limiter inline valve thingy?
Evinrude makes 112hp spl I have one, that has holeshot problems….Any suggestions would be appreciated
Any idea what is the PSI after the rebuilt?
Great video I could change the spark plugs and maybe rebuild the carbs so I’m definitely not going to be a keyboard mechanic and point out what you are doing wrong 😅
Cuál es el torque de las vielas y el crank
Buen trabajo amigo tengo un motor Johnson igual que ese quisiera saber si usted se dedica a este trabajo para arreglar mi motor con usted vivo en Miami florida
I've always been thinking that V-4 engines aren't best part of OMC outboards.( Unfortunately) this video didn't change my mind, althought Brandon made this job look so easy. Btw... My vintage Kawasaki outboard motor is a runner now😊, after sleeping some decades.
Why do you not like the V4's? Whenever I see them torn down they look a heck of a lot like the V6's.
I got 1987 I will try to do one cilynder I have not done any like that before so my question is what dice should I order in Amazon hope you read my message- thanks for the video
What dice?
GReat video. Where can I purchase motor specific shop manuals? The one I have covers multiple years and engines. Need a specific manual for better detail and specs.
Well, what year/HP is your engine? Or give me the model number
1994 Johnson 115 J115TLERC @@BrandonsGarage
Brandon, any thoughts where to find one of these manuals.
I would paint it black with Johnson white and orange and white stripes 😊😊
Are you interested in selling that motor???? If so how much would you want for it???
From what I could see in the video, I probably would have just honed the cylinder wall, slapped in a new piston and rings and called it a day. Although I do have my own Kwik-Way boring bar, it takes all day to bore a cylinder because I only use it every couple of years for motorcycle restorations and I have to learn it all over again and its EASY to make a mistake.
I've been thinking about getting one and trying it out. How hard is it?
Its not hard, but its easy to mess up. I have had a couple throw away cylinders because I don't use the boring bar enough. Not a good thing when boring cylinders on vintage engines! You can find these for just over $1000. I paid $3K for mine and it has not been cost effective as I don't use it often. But if you use one about once a month, it would be well worth it because you can do the job in a few hours once you familiarize yourself with it. Same with doing my own valve jobs.
More good info to add to my knowledge bank when I inevitably have to do this. Shame you couldn't find a machine shop locally. Frustrating living here and never being able to find local businesses to do stuff.
Do the stats…killed my Johnson power head!!!
am sure i've read in the book somewhere if one cylinder is bad you gotta rebore all 4. Especially after #1 clip the ring on a bad angle.
He reused all bolts probably gaskets lol
@chriscobb4939 hell yeah I did.
You must have read it backwards. 1 hole is fine by the book. As is reusing the bolts. They're not torque-to-yield so have no permanent deformation.
@@paulmoir4452 Reboring one hole is fine, but NEVER reuse the big end bolts.
@@k.whiking4372Not required on the old outboards I work on. I'd be a little surprised that it would matter much on a 2-stroke since, unlike a 4-stroke, the rod is always in compression.
I was an OMC tech from 74-86. When did the 115 get the bubble back? Used to be only the 135 and 140
In 85 or 86 they changed from crank HP to prop HP. So the 140 became the 115 and the 115 became the 90. So this is similar to the old 140
You do great job or this job is too hard for
I can’t tell you how many engines I’ve rebuilt in my 38+ years of wrenching but that’s gotta be the fastest rebuild I’ve ever seen 😂😂 Glad to see you used a torque wrench 😂😂 An other great job 👍🏻
Hello sir! I’m looking to upgrade the motor on my 17’ bass tracker. Currently it has a Johnson 40hp. So you happen to have anything larger and preferably with trim. What’s the best way to get ahold of you? Thanks!!
Well where are you located?
I’m in Flagstaff
Or is it possible to add a trim or tilt motor to my existing motor.
What's the average price to have an 60,70,75 hp Evinrude 2 stroke rebuilt ?
2000-3000 I would imagine
Can’t believe they didn’t clean the block!😮 I think I’d rather rebuild an sbc 😂
That thing came apart almost to easy.
I'd dye it up, and hone it a second. See what it looks like,
Putting in a 15, 30, or a 40 over size piston
That was a 30.
Where you located at?
Arizona, you?
@@BrandonsGarage florida
i thought it was only the 140 hp that had the extra manifold between the cylinders the 115 hp engines i have seen only had a flat plate not the ball that contains the manifold
Both types in a 115. Early ones had flat-back; later went to bubble back. Flat-backs are better, more durable engines.
How many hours did that take you
Months. I started it just before summer. Ron's wife fell ill, so he was a little delayed being able to accept the powerhead, then delays on parts, then I got busy with customer projects; and the delays just kept coming. I forgot to order spark plugs, and that delayed the video another week,
53 minutes. 😁
What is a VRO pump?
Mixes oil with fuel right before sending to the carbs. AKA the opposite of premix. Mine failed and I went regular pulse pump and premix.
VRO = Variable Ratio Oil. It mixes the oil & fuel together before sending it to the carburetors. At idle it mixes at between 150:1 & 100:1 ratio depending on years to prevent fouled plugs from excess idling. WOT it would mix around 50:1 ratio.
Very Rarely Operates
Why would you only bore 1 cylinder over and not all 4 never have I seen that and I've built dozens of motors
Money. $120ish for each cylinder + $100 for the piston. Good way to save $660 + tax on a low hour engine within spec. Now, granted, it might be a little cheaper than that; I did buy new rings, and I did pay for the honing, so it's probably closer to a $500 savings.
But it throws the balance out that 1 piston weighs more and will put more vibration in the motor it will eventually break again
I ran 100 hp commercial model evinrudes before honda 4 stroke took over the commercial crabbing industry after around 1000 hours on evinrudes they were junk & it was always the same issue rings sticking & this is what I could not understand why wouldn't they engineer a better design they knew exactly where their engines would fail & never made improvements also that primer injection gadget is a worthless pos
🇦🇺👍
🎉🎉🎉🎉🎉🎉🎉🎉😅😅😅😅😅😅😅😅
Do you have an instagram or facebook page?
I do not. I should though!