KZhead
Ғылым және технология

KiCad 7 STM32 Bluetooth Hardware Design (2/2 PCB) - Phil's Lab

Phil’s Lab
2024 ж. 22 Мам.
136 410 Рет қаралды
Жүктеу

Step-by-step schematic and PCB design tutorial for STM32WB-based hardware (USB, RF, power) in KiCad 7. (Part 2 of 2) (Part 1: • KiCad 7 STM32 Bluetoot... ) PCBs by PCBWay www.pcbway.com
[SUPPORT]
Hardware design courses: phils-lab-shop.fedevel.education
Course content: www.phils-lab.net/courses
Patreon: / phils94
Tag-Connect: www.tag-connect.com/solutions...
[GIT]
www.github.com/pms67
[SOCIAL]
Instagram: / philslabyt
[LINKS]
KiCad 7: www.kicad.org/
STM32CubeIDE: www.st.com/en/development-too...
MCU Datasheet: www.st.com/resource/en/datash...
AN5165: www.st.com/resource/en/applic...
AN2867: www.st.com/resource/en/applic...
Hardware Design Playlist: • Hardware Design
Controlled Impedance: • KiCad Controlled Imped...
PCB Stack-Up & Build-Up: • PCB Stack-Up and Build...
Manufacturing & Assembly Files: • How To Get Your PCB Ma...
[TIMESTAMPS]
00:00 Introduction
01:03 PCBWay
01:42 Courses
02:19 PCB Set-Up
08:14 Design Rules
12:47 Trace and Vias Sizes
13:53 Controlled Impedance
19:15 Importing Components
20:19 Adding Missing 3D Models
24:53 Rats Nets and Net Colours
30:16 Initial Layout
36:16 Tag-Connect and USB Layout (Initial)
39:31 Mechanical Constraints
41:30 RF Layout (Initial)
42:36 Crystal Layout (Initial)
44:13 SMPS Layout (Initial)
45:28 UART Layout (Initial)
46:51 Layout Fine-Tuning
52:46 Decoupling Caps Layout
01:05:57 Misc. Layout
01:21:15 Board Outline
01:26:15 Routing Introduction
01:28:13 Ground Planes
01:31:38 Mounting Holes & Fiducial Markers
01:37:51 Via Placement
01:48:30 RF Routing
01:51:20 Crystal Routing
01:54:40 SMPS Routing
01:58:30 SWD Routing
02:00:21 USB Routing
02:05:29 Misc. Routing (NRST, BOOT0, UART, LED)
02:15:04 Power & Ground Routing
02:25:57 Stitching
02:28:08 Clean-Up (Silkscreen, Teardrops, Non-Functional Pads)
02:33:12 Design Rule Check (DRC)
02:36:03 Further Checks
02:38:11 Bill of Materials (BoM) and Pick 'n' Place (CPL)
02:41:23 Gerber
02:43:54 Additional Documents
02:49:45 Ordering
02:55:56 Outro

Пікірлер

  • Thanks a lot for watching! If you like the video, please leave a like and a comment - this really helps me out :) Part 1: kzhead.info/sun/oc-BdtOwnGKjpY0/bejne.html

    @PhilsLab@PhilsLab5 ай бұрын

    • I am from pakistan but living in germnay. I am PCB designer , I recently shifted to altium, and i started following you. Thanks man ; ich bin sehr dankbar.

      @eemhi@eemhi5 ай бұрын

    • Thanks for your support - und hallo aus Heidelberg :)

      @PhilsLab@PhilsLab5 ай бұрын

    • @@PhilsLab und hallo aus Frankfurt :)

      @eemhi@eemhi5 ай бұрын

    • My experience with Germany is they tend to scam foreigners and pay them less@@eemhi

      @paugasolina5048@paugasolina50485 ай бұрын

    • @@eemhi do you use kicad before shifting to altium?

      @azizbillah@azizbillah5 ай бұрын

  • Exceptional work man, this will most likely become a student standard for designing a board, period.

    @ARBB1@ARBB15 ай бұрын

    • Thanks a lot, that would be awesome! :)

      @PhilsLab@PhilsLab5 ай бұрын

  • Thanks Phil, this is pure gold! You provide guidelines on so many critical topics of the design process! Otherwise it would take years and years of experience to figure out all this on your own!

    @zalbb@zalbb5 ай бұрын

    • Thank you very much - hopefully these are helpful! :)

      @PhilsLab@PhilsLab5 ай бұрын

    • @@PhilsLab I'm absolutely sure that they are! I would also be interested in your opinion about thermal relief SMD pad connection vs. same-net-island_but-no-thermal-relief connection to SMD pads. This is because I believe the latter could more often lead to tombstone'd SMD parts due to unequal heat dispersion capabilities with reference to opposite ends of a two pin SMD component for example. There were examples for both in this video of yours, so I would be interested to know your opinion about the methods. Maybe others could benefit from your response as well? Thanks!

      @zalbb@zalbb5 ай бұрын

  • Another great new feature in KICAD 7 is the pack feature. Just highlight the parts in your schematic you want to place next (e.g. a whole block like RF or USB-C), switch to the PCB Editor window and press "P". This will automatically group the selected parts on your cursor and you can drag them wherever you want. Great video!

    @stupyvy@stupyvy5 ай бұрын

    • Thank you - very cool, I didn't know about that!

      @PhilsLab@PhilsLab5 ай бұрын

  • Perfect , please create more and more projects, those are the type of long videos that we need 👏🔥

    @mohamedyahia809@mohamedyahia8095 ай бұрын

    • Thank you, Mohamed - I'd love to create more of these long-form videos. Unfortunately, even for simple projects such as this one, they take a rather large amount of time...

      @PhilsLab@PhilsLab5 ай бұрын

    • @@PhilsLab Take all my money.... worth every minute

      @konturgestalter@konturgestalter5 ай бұрын

  • Phil - Fantastic series - The attention to detail, tips and design considerations are highly beneficial !!

    @ZoltanHatos-vy1xe@ZoltanHatos-vy1xe19 күн бұрын

  • Amaizing video. Perhaps for your next project you could consider making a video involving a battery powered PCB with support for USB C charging and have support for being powered by both USB & Battery (power muxing) at the same time!

    @anonymgris1987@anonymgris19875 ай бұрын

    • Thank you! Battery-powered/low-power devices is something I'd definitely like to make one or more videos on.

      @PhilsLab@PhilsLab5 ай бұрын

    • I been working on a very low power RF project .. found Ricoh RP605 smps that seems ideal to me

      @peterlaidlaw8655@peterlaidlaw86554 ай бұрын

  • 3 hours! It's just like a New Year came earlier🎉🎉

    @xfxox@xfxox5 ай бұрын

    • Haha thanks :D

      @PhilsLab@PhilsLab5 ай бұрын

  • Nice tip about the color coding of the different net classes, keep up the high quality videos and information 🔥🔥

    @twellmann@twellmann5 ай бұрын

    • Thank you - glad you thought that tip was useful! More videos to come :)

      @PhilsLab@PhilsLab5 ай бұрын

  • So clearly explained, and packed with pure electronics geekery! I thoroughly enjoyed this video and gained a lot of confidence in doing my own projects. Thank you, Phil.

    @insanelydigitalvids@insanelydigitalvids5 ай бұрын

    • Thank you very much for your kind words! Glad this video is helpful.

      @PhilsLab@PhilsLab4 ай бұрын

  • Your channel is a blessing! You deserve more subscribers!

    @julianmuller981@julianmuller981Ай бұрын

  • Terrific job Phil. Your videos are highly detailed and informative. Many thanks.

    @mitchellhw2006@mitchellhw20065 ай бұрын

    • Thanks a lot for watching!

      @PhilsLab@PhilsLab5 ай бұрын

  • WoW! Very nice look onto how its done! Meself using KiCad for a few years now learned some new features. Thanks!

    @blackxiivexil8255@blackxiivexil82554 ай бұрын

    • Thanks a lot!

      @PhilsLab@PhilsLab4 ай бұрын

  • Hi Phil! This was a great tutorial!! I have about 15 years of experience in PCB design and I'd say I agree 99% with all the decisions you took on this design. I came to your video mostly to get knowledge on how to better use KiCad and I'm glad both the KiCad aspects as well as PCB design are very solid. I'll probably get your course on Fedevel to deepen my understanding on KiCad. Thanks for sharing this for free!!!

    @desaoaraujo@desaoaraujo2 ай бұрын

  • This channel is such a gem 💎

    @andrewlloydwebber2616@andrewlloydwebber26165 ай бұрын

    • Thank you very much!

      @PhilsLab@PhilsLab5 ай бұрын

  • been looking forward to this since part 1. I'm currently working on an esp32 board (my first) and while the schematic was relatively straight forward with the hardware design guide (and using other boards I already had been using as reference), the layout and routing still feels very daunting, even with the hardware design guide and reference board. this will help me a lot!

    @ElvianEmpire@ElvianEmpire5 ай бұрын

    • Thank you! Hopefully this video is helpful.

      @PhilsLab@PhilsLab5 ай бұрын

  • For rounding edge cuts, you can right click the rectangle and then click "Fillet Lines" :) Going to have to try the DXF approach though, would make it easier to make a 3d printed case later

    @AndrewOrtman@AndrewOrtman5 ай бұрын

    • Thanks for the tip!

      @PhilsLab@PhilsLab5 ай бұрын

  • Thanks a LOT Phil. I will be doing these projects during my break! Bless you man. Please make one with RF or FPGA

    @faizanmalik7886@faizanmalik78865 ай бұрын

    • You're very welcome - I hope all goes well with your own designs! :)

      @PhilsLab@PhilsLab5 ай бұрын

  • Been looking forward to this one since part 1!

    @GregCormier@GregCormier5 ай бұрын

    • Thank you, Greg!

      @PhilsLab@PhilsLab5 ай бұрын

  • Yess, the second part! My life feels whole now. ☺

    @gergelyhalasz9754@gergelyhalasz97545 ай бұрын

    • Hahah thank you

      @PhilsLab@PhilsLab5 ай бұрын

  • the video is top again- and for me the first 60min are so important(settings before routing etc.) , because I didn´t know that with net class colors, which mae route much easier- thanks Phil great work.

    @haraldh.9354@haraldh.93545 ай бұрын

    • Many thanks, Harald! Glad it was useful.

      @PhilsLab@PhilsLab5 ай бұрын

  • Really love your Phil's Lab video series.

    @nicka3375@nicka33752 ай бұрын

    • Thanks!

      @PhilsLab@PhilsLab2 ай бұрын

  • Incredible amount of information thanks a lot for this

    @hamburgengineer@hamburgengineer3 ай бұрын

  • Phil, i really really hope this content gets good views for you (the work you put in is incredible as always)!!! Appreciate the youtube algorithm may not be friendly with these long form videos, and you are relying on subs to watch (which they will as thats why we sub!). I've always LOVED your content so please keep on the good work! Something I really liked was when you made the m.2 card. Would really love to see more of the 'high end' stuff like pcie implementations (now the pi 5 has a pci breakout - 2 lane - i could see a 'market' for people wanting more info on things they make for themselves using it rather than relying on hats). Have you ever thought about CM4 carrier board design as it has the mix of matching B2B connector layouts, pci, usb, etc.. however do appreciate your main knowledge base is STM32. I find all your content so therapeutic! I know you use the Tag connect pogo pin thing but any tips of homebrewing it as the official ones are stupidly expensive for what they are £40+ for some ribbon cable, 6 pogo pins and cheap molded plastic... we know the cost price to tag-connect is gonna be cheap like £1-5....

    @Thats_Mr_Random_Person_to_you@Thats_Mr_Random_Person_to_you5 ай бұрын

    • Thank you very much! Surprisingly, these long-form KiCad videos typically perform far better in terms of views compared to shorter ones/different topics. I have a number of more advanced/non-STM32 vids on the channel, also touching on PCIe routing with FPGAs. But I agree, a carrier board for a CM4 or NVidia SBC would make for interesting content - thanks for the suggestion! Regarding Tag-Connect, the upfront cost may seem high, but the practicality of the cables, ease-of-use, not needing headers on boards makes up for it many, many times in my opinion. Thanks for your support!

      @PhilsLab@PhilsLab5 ай бұрын

    • ​@PhilsLab yh a carrier board might be fun as you have a LOAD of options to design for a mix of easier and complex IO. You could add pci to usb or ethernet chips, pci mux. Would love to see high-speed usb (ie usb 3.x) as well with usb c. As always love the content and wishing you a GREAT christmas and heres to 2024 and wishing it be a hreat year for you and the channel

      @Thats_Mr_Random_Person_to_you@Thats_Mr_Random_Person_to_you5 ай бұрын

    • Many thanks for the suggestions! Thank you, I hope you have a great Christmas and 2024 as well :) All the best!

      @PhilsLab@PhilsLab5 ай бұрын

  • Excellent tutorial as aways!!! Now, what we really want is the same procedure but made in Altium :)

    @pixlfactory@pixlfactory4 ай бұрын

  • Thank for this detailed and professional tutorial. However, 3:55 as a hobbyist I can't agree with this statement that 4 layers are very inexpensive. The same number of 2 layer pcbs from pcbway would cost $5. Or 10 times less expensive than 4 layers! Considering the fact that half of my projects were less than $50 (including components and enclosure), I would say that unless it is required by technology or design is very complex, I always to try to route pcb in 2 layers first.

    @MSP_TechLab@MSP_TechLab4 ай бұрын

  • You have really been helpful in my project and I am grateful. Please continue to make videos like this it helps.

    @Eleazer.changetheworld@Eleazer.changetheworld5 ай бұрын

    • Thanks a lot, glad these videos are helpful!

      @PhilsLab@PhilsLab5 ай бұрын

  • "BluePhil", nice naming. And I learned a couple of useful tips for my next design.

    @Gengh13@Gengh135 ай бұрын

    • Thank you! :)

      @PhilsLab@PhilsLab5 ай бұрын

  • Great Video! Nice Phil!

    @kiprof4350@kiprof43504 ай бұрын

    • Thanks a lot!

      @PhilsLab@PhilsLab4 ай бұрын

  • great video as always man! will be waiting for the Altium version.

    @mochariefazzmisantoso2508@mochariefazzmisantoso25085 ай бұрын

    • Thank you! I have a similar STM32 + Altium video here: kzhead.info/sun/g7F-oLWScGKcZmw/bejne.html

      @PhilsLab@PhilsLab5 ай бұрын

  • Brilliant tutorial, thanks!

    @mikehibbett3301@mikehibbett33015 ай бұрын

    • Thank you, Mike!

      @PhilsLab@PhilsLab5 ай бұрын

  • Fully appreciated ur works..

    @shamssalehin2376@shamssalehin23765 ай бұрын

    • Thank you very much!

      @PhilsLab@PhilsLab5 ай бұрын

  • Thanks!! Awesome video. I learned a lot from it!

    @wcaeng@wcaeng4 ай бұрын

    • Thanks!

      @PhilsLab@PhilsLab4 ай бұрын

  • Watching it right away 🎉🎉🎉

    @Ajaykrishna97_@Ajaykrishna97_5 ай бұрын

    • Thank you :)

      @PhilsLab@PhilsLab5 ай бұрын

  • Pure Gold! Thanks!

    @GingerBeker@GingerBeker5 ай бұрын

    • Thanks a lot!

      @PhilsLab@PhilsLab5 ай бұрын

  • Finally, thank you again Phil.

    @fra5715@fra57155 ай бұрын

    • Thanks for your support! :)

      @PhilsLab@PhilsLab5 ай бұрын

  • Great video as usual. Thanks

    @rrhamelin@rrhamelin5 ай бұрын

    • Many thanks!

      @PhilsLab@PhilsLab4 ай бұрын

  • Excellent video! Thank you!

    @dsrsolucoesemeletronica8373@dsrsolucoesemeletronica83734 ай бұрын

    • Thanks for watching!

      @PhilsLab@PhilsLab4 ай бұрын

  • @PhilsLab thank you for you videos especially for KiCad it is really very helpful, I just use it as tutorial to create mine project (best one in youtube right now)

    @zionvad@zionvad3 ай бұрын

  • thanks philsLab, the best pCB designer

    @toto123752@toto1237525 ай бұрын

    • Thank you!

      @PhilsLab@PhilsLab4 ай бұрын

  • Great Video, Phils Thanks

    @eemhi@eemhi5 ай бұрын

    • Thank you!

      @PhilsLab@PhilsLab5 ай бұрын

    • The video came out 3 minutes ago. How about you actually watch it before you call it good?

      @fredthechamp3475@fredthechamp34755 ай бұрын

    • @@fredthechamp3475 , You are absolutely right, but i know the content from Phil's and Robert So, i am 100% sure the video is great.

      @eemhi@eemhi5 ай бұрын

  • Cool video, thanks for sharing it :)

    @Bianchi77@Bianchi774 ай бұрын

  • The 'rule of thumb' is to never break up/interrupt the ground pours. But there are times (definitely seen it on professional boards) where you very much want seperated ground planes (I think this is for thing where there is a seperate analogue ground). I dont think I've seen many people cover pcb layout design where you really do want separate planes and like super uber use of via stiching etc.. is it one of those areas of knowledge like 'you KNOW when you need to do it because you have the specific special expertise to know about it' and basically every other time, without fault, you don't have split planes. Other than the PCB antenna video you made a bit back have you any other experience with PCB RF filters? I only ask as it seems usual for the layout team to be a seperate group from the schematic and design teams, and it seems like they may not have the 'full' knowledge of how to design such rf stuff (ie the calcs and knowing what needs to be done etc to waht signals etc) but still need to then layout and route it..... which sounds 'fun'...... I assume the schematic team and company as a whole would have custom footprints and the pcb layout team just need to lay them out even if they don't fully know how they work

    @Thats_Mr_Random_Person_to_you@Thats_Mr_Random_Person_to_you5 ай бұрын

  • You are inspiring new electrical engineers students

    @hollyizza3672@hollyizza36724 ай бұрын

    • Thank you, I hope so! :)

      @PhilsLab@PhilsLab4 ай бұрын

  • Keep the Great work 👍👍👍👍

    @ibrahimesam365@ibrahimesam3655 ай бұрын

    • Thank you, Ibrahim!

      @PhilsLab@PhilsLab5 ай бұрын

  • Thank you so much this video help me a lot

    @safwaniiiiiiz@safwaniiiiiiz5 ай бұрын

    • I'm very glad to hear that - thanks for watching!

      @PhilsLab@PhilsLab5 ай бұрын

  • awesome video!

    @paugasolina5048@paugasolina50485 ай бұрын

    • Thanks for watching!

      @PhilsLab@PhilsLab5 ай бұрын

  • This is just GREAT STUFF!

    @sigicnc@sigicnc5 ай бұрын

    • Thanks a lot!

      @PhilsLab@PhilsLab4 ай бұрын

  • More power to you, man. When can we expect a firmware tutorial on this, desperately need one guide, asking my Phil god for it! Thanks buddy.

    @user-rd2ro4pg5u@user-rd2ro4pg5u5 ай бұрын

    • Thank you very much! Firmware tutorial sometime start of next year - I have a few other video ideas lined up :)

      @PhilsLab@PhilsLab4 ай бұрын

  • ❤ thank you Phil!

    @pyrhockz@pyrhockz5 ай бұрын

    • Thanks for watching! :)

      @PhilsLab@PhilsLab5 ай бұрын

  • Can you do one more video on custom panelization of PCBs in KiCad?

    @ranaharsh365@ranaharsh3655 ай бұрын

  • thanks a lot for your work!

    @perceptron9834@perceptron98344 ай бұрын

    • Thank you for watching!

      @PhilsLab@PhilsLab4 ай бұрын

  • Great work again as expected,waiting for more videos but please in allium XD

    @patrickrostami@patrickrostami5 ай бұрын

    • Thank you, Patrick - more to come!

      @PhilsLab@PhilsLab4 ай бұрын

  • Love the name of the board!

    @shahinhaque95@shahinhaque954 ай бұрын

    • Thanks!

      @PhilsLab@PhilsLab4 ай бұрын

  • Maravilha de aula amigo, Abraço do brasil.

    @RicardoBHubner@RicardoBHubner5 ай бұрын

    • Thank you very much, greetings from Germany :)

      @PhilsLab@PhilsLab5 ай бұрын

  • excellent as always Phil thanks .. a quick question though.. should the USB shield be grounded or left floating instead?

    @trevorhunt6083@trevorhunt60832 ай бұрын

  • Very informative! Where did you get the pi network values?

    @osmanpasha96@osmanpasha963 күн бұрын

  • Heads up to all - 2:32:18 - If you de-select "Keep Outside Layers", you will get some questions during review (at least from JLC) about your design. I don't have ground pours on top/bottom layers but they seemed confused if they were blind/buried vias (not offered) or through holes.

    @GregCormier@GregCormier4 ай бұрын

  • Very interesting and well done tutorials. I suggest to the viewers to check also the two courses of Mr. Phil, they are worth every single euro.

    @gbernazzali@gbernazzali3 ай бұрын

    • Thank you very much!

      @PhilsLab@PhilsLab2 ай бұрын

  • Cheers!

    @pixelrancher@pixelrancher5 ай бұрын

  • Awesome work! How is the 2.4GHz RF performance? Any plans to use a spectrum analyzer like TinySA?

    @joseleflores4591@joseleflores45914 ай бұрын

    • Thanks, Jose! Yes, I'm gonna make a video on testing the matching network/antenna performance using a NanoVNA.

      @PhilsLab@PhilsLab4 ай бұрын

  • Thank you for the video. Even using KiCAD for a long while, I've got some good tips from it. What do you think about using microstrip vs coplanar waveguide for controlled impedance traces? Do you have any preference on that? If so, what's your reasoning? I haven't done much RF design, but the last one had a 4G modem. I used the suggested 4 layer Signal/GND/GND/Signal stackup and went for coplanar waveguide on top layer, GND copper pour on both external layers, but I might have just went with microstrip and no pour on external layers.

    @Kuro-ik3qn@Kuro-ik3qn4 ай бұрын

  • Thank You

    @alexramlakhan7858@alexramlakhan78584 ай бұрын

    • Thanks for watching, Alex!

      @PhilsLab@PhilsLab4 ай бұрын

  • I noticed that in my PCB editor, the "show pads in outline mode" (button on the left) was on by default, or perhaps I'd activated it with a hotkey at some point. Turning this off (as in Phil's video) makes things a lot easier to read.

    @JM-iu7qx@JM-iu7qx2 ай бұрын

  • Hi Very nice video. Can you please explain how I can get the plugin or if you can give the link of the plugin for generating BOM because the old one for kicad 6 is not working anymore in kicad 7.

    @muhammadzain1023@muhammadzain1023Ай бұрын

  • Hi Phil, Could you do a similar video with NB-IoT or Do you know where I can find how to design the same with NB-IoT? Thanks from Spain!

    @polbm99@polbm993 ай бұрын

  • Nice

    @diwakarmr9124@diwakarmr91245 ай бұрын

  • Hello Phil, Will there be a video on a board with the ESP32-S3 at some point? I would very much like to see how to create a custom PCB for it and maybe with a built-in display using either I2C or SPI :-)

    @Oerbaek@Oerbaek5 ай бұрын

    • Probably at some point, yes! Although I'd like to showcase an nRF design first :)

      @PhilsLab@PhilsLab4 ай бұрын

  • Very nice tutorial ! what software do you use to print out all manufacturing data you're presenting at the end of the video please ?

    @Scientific7556@Scientific75564 ай бұрын

    • The examples were actually made using a different ECAD tool (Altium Designer). However, I believe there are some plugins available for KiCad that should be able to create similar drawings.

      @PhilsLab@PhilsLab4 ай бұрын

  • This is an amazing series, thank you. Question: I followed everything to a T, yet I'm getting a ton of DRC violations. For example, on the WB55 footprint, for every pad I'm getting a "Front solder mask aperture bridges items with different nets" error. Thanks for any guidance you can provide.

    @jchatterton2113@jchatterton21134 ай бұрын

    • Thank you! Regarding that DRC violation, you can either space components further apart, or reduce the solder mask openings (we set them to 0 in the video and let the manufacturer adjust). Check out this forum post, for example: forum.kicad.info/t/6-99-drc-fail-solder-mask-aperture-bridges-items-with-different-nets/35311

      @PhilsLab@PhilsLab4 ай бұрын

  • Thank you Phil , will u do Altium version video ?

    @mahdisaad5041@mahdisaad50415 ай бұрын

    • I have a full STM32 + Altium tutorial here: kzhead.info/sun/g7F-oLWScGKcZmw/bejne.html

      @PhilsLab@PhilsLab5 ай бұрын

  • Thanks for great content Phil. Soon Kicad 8 will be out and you get to make it again :) I have a question on how the component sourcing works in practice. You specify parts from Mouser in germany in your BOM and PcbWay will source them. But do they just source the few components needed for your boards? Don't they need to order full reels of components for their PnP machines? For example the USB connector you specified, if they don't have it in stock, how do they go about that? Also, can PcbWay source components from LCSC? Wouldn't this be much cheaper since AFAIK they keep large stocks of components from various manufactureres, and they're located in china. A wish you a merry christmas!

    @zeeebrenn@zeeebrenn5 ай бұрын

    • Thanks for watching! Haha yeah, KiCad 8 vid will have to be made soon! Since PCBWay handles many orders at a time, they will combine and order 'in bulk' from various distributors to get parts together for various customers in parallel. Yes, they can source from pretty much any vendor (incl. LCSC). Happy holidays!

      @PhilsLab@PhilsLab5 ай бұрын

  • When I click on the impedance control, the price increases by 50 euros 😱. I took the 0.17mm and 0.22mm and ordered without impedance control and got pretty the same price as you.

    @perceptron9834@perceptron9834Ай бұрын

  • Do you have a PDF of the schematic?

    @ahbushnell1@ahbushnell1Ай бұрын

  • Very good explanation of the entire process but I am still not clear which service is better for PCB manufacturing and assembly for maker projects and hobby users: PCBWay or JLCPCB? If you can give us your evaluation, thank you!

    @javivi2097@javivi20975 ай бұрын

    • Thank you! PCBWay offers quite a bit more flexibility when it comes to both PCB specs and assembly, which can be/is very important in more intricate/advanced designs. For maker/hobby boards usually this doesn't matter too much of course, so in many cases either option is fine. I am biased however with the PCBWay sponsorship :)

      @PhilsLab@PhilsLab5 ай бұрын

  • Sir excellent video. Keep it up. Can you make video about higher ampere pcb design.

    @RatonEEE-bp2my@RatonEEE-bp2my5 ай бұрын

    • Thank you, good idea!

      @PhilsLab@PhilsLab5 ай бұрын

    • My pleasure ❤️

      @RatonEEE-bp2my@RatonEEE-bp2my5 ай бұрын

  • is there any 802.15.6 example?

    @mitkosokolov9382@mitkosokolov93824 ай бұрын

  • do you plan to make a tutorial how to route smd antena / rf-antenna design ? :)

    @perceptron9834@perceptron98342 ай бұрын

    • Yes, that's a video for this month (hopefully) :)

      @PhilsLab@PhilsLabАй бұрын

  • I could not find the schematics in the description

    @Ajaykrishna97_@Ajaykrishna97_5 ай бұрын

    • I'm afraid I don't provide the design files for this. My personal experience is that I learn better by doing designs myself from scratch, rather than copying.

      @PhilsLab@PhilsLab5 ай бұрын

    • @@PhilsLab I get it , I just wanted a pdf version of it just to compare my design against it as a reference design. Anyways the video was a great help for me. Thank you. :)

      @Ajaykrishna97_@Ajaykrishna97_5 ай бұрын

  • Have you ever done emc testing in test house? Have you ever had an emc problem ? Would the board designed here pass emc tests ?

    @AlbertRei3424@AlbertRei34245 ай бұрын

    • Yes, I've done this many times. And EMC problems of course do crop up at times - I'd like to make some videos on the process. These types of boards typically require an RF can/shield in many cases to pass certification testing (e.g. check out pre-certfied modules from u-blox, ST, u-blox, etc..).

      @PhilsLab@PhilsLab5 ай бұрын

    • @@PhilsLab definitely a good idea of video! Following the design of a pcb from the beggining to the emc testing, emc testing are expansive so maybe recording the process for a board you do at your job? The most important is the thought process to counter emc issues, not the emc testing themselves

      @AlbertRei3424@AlbertRei34245 ай бұрын

  • I tried Altium for some time and got back to KiCAD, cause it does not add any obstacles. You just draw and trace. I don't develop 12 layers AMD motherboard, and so will never use 90% of Altium features, but I found out that it does not help to make work fast. Please, more edu vids with KiCAD. May be with some useful plugins.

    @sc0or@sc0or4 ай бұрын

  • Thank you sir for your resourceful contents. I would like to ask what you studied in college and how you were able to learn pcb design.

    @dayoflic_@dayoflic_5 ай бұрын

    • Thanks for watching! I studied electrical and control systems engineering, however, PCB design wasn't part of the curriculum. This is pretty much all self-taught.

      @PhilsLab@PhilsLab5 ай бұрын

    • @@PhilsLab I'm grateful for your response. Can you suggest a pathway how one can self-teach electronics and pcb design or do you have a video on it? Thank you.

      @dayoflic_@dayoflic_5 ай бұрын

  • Respect ++

    @mridulsanthosh811@mridulsanthosh8113 ай бұрын

  • 1:50:34 do we need to add a RF guard ring for better performance? Will it make any good , could you please explain the use of a RF guard ring

    @Ajaykrishna97_@Ajaykrishna97_5 ай бұрын

    • You could do if you want to go through certification, for example. I may make a video on this in the future.

      @PhilsLab@PhilsLab5 ай бұрын

    • @@PhilsLab got it. ST have a companion IPD ic for RF , if I add that do i still wanna do the trace impedance matching? Also that ic is more expensive than a LC filter , is that worth it?.

      @Ajaykrishna97_@Ajaykrishna97_5 ай бұрын

  • i didn't understand 2:43:54 "Additional Documents" parts. Although maybe my English not good enough to understand. But can someone save me a time for saying is that important part or just a "making the pcb close enough to the perfect part"? if someone answer me, I'll appreciate it.

    @sabbrush6001@sabbrush60015 ай бұрын

  • So i can just opt for Chip antenna instead of antenna connector?

    @ihsanas@ihsanas5 ай бұрын

    • Follow the datasheet of the chip antenna - this'll give you information on GND/copper structures, and matching impedance. But in essence, it's a pretty straightforward implementation.

      @PhilsLab@PhilsLab5 ай бұрын

  • 🐐

    @HipocratesAG@HipocratesAG5 ай бұрын

  • I'd also like to know if it was in college you learnt a bulk of the knowledge of pcb or you self-leaned. What would you suggest someone studies and learns to perfect this skill.

    @dayoflic_@dayoflic_5 ай бұрын

    • He made a video on that topic, called something lile 'my journey pcb design'

      @AlbertRei3424@AlbertRei34245 ай бұрын

  • Did anyone submit the gerber files to PCBway to only have the board manufactured? I’m curious what anyone else might have gotten back in terms of the price. Mine (without shipping) was roughly $105. Thanks!

    @cowanjt@cowanjt4 ай бұрын

  • What does this PCB do?

    @AbhaySingh-ht1qr@AbhaySingh-ht1qr13 күн бұрын

  • Ah, the quirks are always something with KICAD but it is free so its just a workflow thing. The worst package I use professionally is PADS, if you want to hate your job give it a try!

    @matthewprestine1974@matthewprestine19745 ай бұрын

    • Definitely! I must say, it had also been about a year of not using KiCad, before preparing for this video, as I've just been using Altium - I'm sure there are easier/better ways of doing things at times. Definitely haven't heard the greatest things about PADS haha..

      @PhilsLab@PhilsLab5 ай бұрын

    • @PhilsLab I dont recall if you did one, but a video about multi-sheet schematics in KICAD would be nice. Its another quirk that is strange compared to any other EDA.

      @matthewprestine1974@matthewprestine19745 ай бұрын

  • What is the total price for 5 boards that PCBWAY quoted?

    @bartoandras@bartoandras5 ай бұрын

    • Assembly was about 130 USD for 3 pieces incl. components. PCB cost around what you see in the video - there can be a surcharge for impedance control.

      @PhilsLab@PhilsLab5 ай бұрын

  • can you make any video about electronics as core , R, L,C,Antenna design, not the basic level but advance level such as designing own circuit . emebedded is like only programming , i looking for designing tutorials.

    @dhishoomdhishoom8574@dhishoomdhishoom85745 ай бұрын

    • Yes, definitely - something I have a few upcoming videos planned on!

      @PhilsLab@PhilsLab5 ай бұрын

  • Make video on PoE ethernet complete design guide, Thanks

    @eemhi@eemhi5 ай бұрын

    • At some point, definitely! :)

      @PhilsLab@PhilsLab5 ай бұрын

  • 👍🙏❤️

    @tamaseduard5145@tamaseduard51455 ай бұрын

  • Small tip, any reference PCB MIFA Antenna design would work better than these chip antennas. These have bad null points.

    @aneeshprasobhan@aneeshprasobhan5 ай бұрын

    • Indeed. I recently (finally) acquired a nanoVNA and wanted to test out various antennas, as I have used trace and off-board antennas quite a bit and thus wanted to give this a go :)

      @PhilsLab@PhilsLab5 ай бұрын

    • ​@@PhilsLabim hyped to see your result soon :)

      @lynes2peters438@lynes2peters4385 ай бұрын

    • Just FYI, the NXP application Note AN11994 talks about a decent MIFA design.@@PhilsLab

      @aneeshprasobhan@aneeshprasobhan5 ай бұрын

  • Arduino integrated with nrf24 module

    @Onlyindianpj@Onlyindianpj4 ай бұрын

  • 19:34

    @abcdefg91111@abcdefg911112 ай бұрын

  • 1:37:51

    @abcdefg91111@abcdefg911112 ай бұрын

  • 2:19:22

    @abcdefg91111@abcdefg911112 ай бұрын
KZhead