How to test a car starter out of the car, applies to most starters.
Пікірлер
Nja you have to see if the coals are worn out. Moisture often gets inside the oil sand. It's for all cars. It is necessary to open, clean and change the carbons and clean the contacts.
@raitshots10 ай бұрын
👍👍👍👍
@dawidkwiecien99385 ай бұрын
ماشاءاللہ ❤❤❤
@MuhammadUmer-nc7tg8 ай бұрын
I didn't see the solonoid engaging
@owenndazizi67379 ай бұрын
When you attach the positive to one side of the wire, test the other side of the wire to make sure you are getting power for sure. If you are getting power then the selonoid may be bad. How old is the car and how many miles?
@cgcars34279 ай бұрын
Ma nel motorino nuovo, non esce l'escursione dell'ingranaggio.😮
@balbeppe746210 ай бұрын
U joined those wires wrong mr
@calvinbom6 ай бұрын
No surprise this starter died, because you "banged it"
@paulaur4 ай бұрын
Hey genius, the starter was already bad hence why I took it out of the car. It gets stuck so I banged it and it worked for a little but too old, worn and rusted.
@cgcars34274 ай бұрын
@@cgcars3427yep, if you get stuck somewhere you have to hit it to get home or where you're going.
@markleach2177Ай бұрын
Excellent pilgrims 😁pip pips
@patrickjobling8676 Жыл бұрын
Solonide was not doing its job on the new stater thou. Only spin but not moving foward
@kemabosh358811 ай бұрын
Are they. Inter changeable with tatest model starter
@gilbertkarmun88947 ай бұрын
Latest model 😂
@gilbertkarmun88947 ай бұрын
😂. they should be
@cgcars34277 ай бұрын
Why the new one is goat a loop wire on but is not on the old one
@user-jc6jv6kn2hАй бұрын
They both are wired the same. May be hard to tell.
@cgcars3427Ай бұрын
Uhhh….
@just__dave10 ай бұрын
What??your testing a new one😊
@gaamedjames339411 ай бұрын
What🤨? Just showing the process of testing it and that the test actually works.
Nja you have to see if the coals are worn out. Moisture often gets inside the oil sand. It's for all cars. It is necessary to open, clean and change the carbons and clean the contacts.
👍👍👍👍
ماشاءاللہ ❤❤❤
I didn't see the solonoid engaging
When you attach the positive to one side of the wire, test the other side of the wire to make sure you are getting power for sure. If you are getting power then the selonoid may be bad. How old is the car and how many miles?
Ma nel motorino nuovo, non esce l'escursione dell'ingranaggio.😮
U joined those wires wrong mr
No surprise this starter died, because you "banged it"
Hey genius, the starter was already bad hence why I took it out of the car. It gets stuck so I banged it and it worked for a little but too old, worn and rusted.
@@cgcars3427yep, if you get stuck somewhere you have to hit it to get home or where you're going.
Excellent pilgrims 😁pip pips
Solonide was not doing its job on the new stater thou. Only spin but not moving foward
Are they. Inter changeable with tatest model starter
Latest model 😂
😂. they should be
Why the new one is goat a loop wire on but is not on the old one
They both are wired the same. May be hard to tell.
Uhhh….
What??your testing a new one😊
What🤨? Just showing the process of testing it and that the test actually works.