KZhead
Автокөліктер мен көлік құралдары

Easy and Cheap way to Compress a Brake Caliper Piston Without Any Special Tools

ScrewsNutsAndBolts
2021 ж. 22 Там.
625 282 Рет қаралды
Жүктеу

This is a cheap and simple way to compress a brake caliper piston without the need for any special tools. All you need is a couple of small pieces of wood and a couple of screwdrivers. This method works with most front brake calipers as the pistons push straight back into the caliper. It will not work with most rear brake caliper pistons as they have to be rotated as they are being pushed in due to the integrated handbrake mechanism. This video shows how to compress a rear brake caliper both with, and without special tools: • Rear Brake Caliper Pis...
Thanks for watching, please comment, like and subscribe !.
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2023
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.

Пікірлер

  • Here's a video showing how to compress a rear caliper piston both with, and without special tools: kzhead.info/sun/ddeSd8dtpaqao58/bejne.html

    @screwsnutsandbolts@screwsnutsandbolts6 ай бұрын

    • I tend to use my wood working trigger clamp but have also used those door lifting air bags.

      @LloydBrodrick-ne5ei@LloydBrodrick-ne5ei3 ай бұрын

  • Nice QUIET Video....just the welcome sounds of happy bird calls in background....🐦🐦❤

    @RockinProfessor@RockinProfessor21 күн бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts20 күн бұрын

  • Retired, but every days a school day, great tip thanks for your time doing this video

    @jacksrus@jacksrus2 ай бұрын

    • You're very welcome !, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • Using the old brake pads is very clever. The applied force is evenly distributed and any damage that could occur would only be to the old brake pads that you're going to throw out any way. Thanks so much.

    @TheInevitableHulk@TheInevitableHulk Жыл бұрын

    • You're very welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Thank you sir! You saved the day. Was doing a brake pad job and I didn't have a C clamp. Had a caliper tool, but the piston wouldn't budge. Found a block of wood and this worked like a charm. God bless you!

    @jeffsadowski7759@jeffsadowski775911 ай бұрын

    • You're very welcome

      @screwsnutsandbolts@screwsnutsandbolts11 ай бұрын

  • Lifesaver. I've done plenty of brake jobs and never had a problem compressing the caliper with a C clamp but today it would not budge. I was ready to give up and buy a new caliper thinking it was bad but then I came across the trick with the screwdrivers and it worked like a charm. I don't think I will ever use a C clamp again. Thanks.

    @stevenvecciarelli4679@stevenvecciarelli46798 ай бұрын

    • You're welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts8 ай бұрын

  • Thanks for watching my video. If you found this or any of my other videos helpful, maybe you could consider supporting my channel by using the ‘Thanks’ button below each of my videos. Your support would be really appreciated, thank you ! 👍 Screwsnutsandbolts

    @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Just did this with the 2 screw drivers, worked like a charm!

    @robertmartin1269@robertmartin126920 күн бұрын

  • My mechanic told me to buy a new one but i kept searching videos and could find yours. Thank you so much for this awesome video!

    @joethetraveller2755@joethetraveller2755 Жыл бұрын

    • You're very welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Happened to do this yesterday changing brake pads used the wood method,worked a treat!

    @aala7337@aala733719 күн бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts19 күн бұрын

  • That is a great technique I've never seen before. What I like in this approach that you can compress the piston without removing pads. On one of our cars (2003 Chevy Cavalier) the outer pad is locked w/special clamps, you need to have 2 screwdriver to put it back. And sometimes you just need to remove the caliper fm/the disc for other jobs. It is usually hard for me to put the caliper back on the disc, though I open the brake fluid cap. Thank you for this so clever tip.

    @olenaerhardt7725@olenaerhardt77255 ай бұрын

    • You're very welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts4 ай бұрын

  • Brilliant! Excellent video. Thank you!

    @PhunkyChikin@PhunkyChikin20 күн бұрын

    • Thank you !

      @screwsnutsandbolts@screwsnutsandbolts19 күн бұрын

  • What a great tip! Thanks also for demonstrating the Cube.I wasn't aware that such a tool was available. Much cheaper than the standard one. Thanks again for a great channel.M

    @markwilliams2830@markwilliams28302 жыл бұрын

    • Thank you as always :)

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • You just saved me! With using the old brake pad trick 💕🙏🏾🙏🏾

    @babygurlcrazy@babygurlcrazyАй бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • This got me out of a tight spot, thank you

    @DavidxLB@DavidxLB19 күн бұрын

    • You're welcome!

      @screwsnutsandbolts@screwsnutsandbolts19 күн бұрын

  • Brilliant video thanks for uploading.

    @savinggracechurch4112@savinggracechurch41123 ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts3 ай бұрын

  • Wow! Very smooth! Well done!

    @iWalkChris@iWalkChris3 ай бұрын

    • Thank you !

      @screwsnutsandbolts@screwsnutsandbolts3 ай бұрын

  • Bless you.

    @reallychadical@reallychadicalАй бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • Love you for this right now.

    @ScreamingRabbits@ScreamingRabbitsАй бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • Thanks for the info.. I was so close to calling it quits. Thanks alot

    @leninvega3158@leninvega3158 Жыл бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • BLESSS YOUUUU!! A big pain in the ass (I literally used a mini square of wood) but my caliper is now compressed with the screwdriver method. Thank you!

    @KINGCVSEY@KINGCVSEY Жыл бұрын

    • You're very welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Many thanks for this easy way. I will try it next time.

    @chachouachokri7860@chachouachokri78602 жыл бұрын

    • You're welcome :)

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • Thanks for sharing

    @andrewthacker114@andrewthacker1142 ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • Too easy, thanks

    @philmissen2365@philmissen2365Күн бұрын

    • You're welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandboltsКүн бұрын

  • aye man I did this right here and it worked perfectly, thanks.

    @gabrielortiz9594@gabrielortiz9594 Жыл бұрын

    • You're very welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Nice and simple idea..❤

    @SAM-tw6ld@SAM-tw6ld4 ай бұрын

    • Thank you !

      @screwsnutsandbolts@screwsnutsandbolts4 ай бұрын

  • Thank you.

    @Tripp111@Tripp11119 күн бұрын

    • You're welcome!

      @screwsnutsandbolts@screwsnutsandbolts19 күн бұрын

  • So So smart SIR!!

    @Tuan-DuongNgo@Tuan-DuongNgo2 ай бұрын

    • Thank you !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • Excellent explanation! I will try your method as soon as i have to replace the pads (never replaced them as a DIY mechanic, by the way) Thanks:)

    @galimusic7164@galimusic7164Ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • wow, it's such a clever maneuver.

    @samwu8070@samwu80702 ай бұрын

    • Thank you !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • you saved my life, thanks!

    @patosaavedra1@patosaavedra19 ай бұрын

    • You're welcome!

      @screwsnutsandbolts@screwsnutsandbolts9 ай бұрын

  • Thanks!

    @lancetaylor6976@lancetaylor69766 ай бұрын

    • Thank you very much Lance, I appreciate your support ! 👍👍

      @screwsnutsandbolts@screwsnutsandbolts6 ай бұрын

  • Thank you very much sir, u saved me a lotttt of trouble

    @kaleabzenebe1407@kaleabzenebe14072 жыл бұрын

    • You're very welcome

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • Great video. Here's a tip. Before you compress the piston, spray the rubber dust shield with silicon. It will prolong the life of the rubber.

    @frankhoward7645@frankhoward76453 ай бұрын

    • Thanks for the info!

      @screwsnutsandbolts@screwsnutsandbolts3 ай бұрын

  • Instead of wood planks, i use a pair of wrenches and the old brake pads. Thanks for the idea. It saved me a lot of time looking for clamps.

    @danstheory4164@danstheory4164 Жыл бұрын

    • You're very welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • I have got the rotation ones any simpler way to do them please please very good and clever trick

    @khalidarshad3448@khalidarshad34482 жыл бұрын

  • Best video on the KZhead. Been working on cars for 40 years and just now I see this?! so much time wasted!

    @RideAMAP@RideAMAP2 ай бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • Wow! Thanks!

    @ab-kn1gg@ab-kn1gg2 ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • Great 👍 work ✅

    @imwmanish@imwmanish2 жыл бұрын

    • Thank you! Cheers!

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • I can confirm the wood method works :D Thanks for sharing

    @7maszi7@7maszi7 Жыл бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Thanks man, nice.

    @abdelhafidramdani7393@abdelhafidramdani7393Ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • Saved me time and money 💡

    @dtownzfinest8608@dtownzfinest86082 ай бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • I use a big C clamp against the old brake pad and gently tighten it. Compresses the piston evenly. Very easy to do.

    @comedycafe3262@comedycafe3262 Жыл бұрын

    • I use a 6 inch c clamp. And or compressed air with a block of wood to keep the piston in its bore, but be free to remove the piston after the blast.

      @jayjaynella4539@jayjaynella453911 ай бұрын

    • That is indeed the best way. C clamps are cheap too. Not a specialized tool by any means.

      @nevinkuser9892@nevinkuser989211 ай бұрын

    • same here im using c clamp

      @VykersTechTips@VykersTechTips10 ай бұрын

  • Damn! That works great. Wish I’d known this years ago. I’ve been using a c-clamp. Thank You!

    @robertgarrett7007@robertgarrett70072 ай бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • You just saved me some money. Thanks. 👍🏿

    @homeschoolingandawareness@homeschoolingandawareness10 ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts10 ай бұрын

  • Just used this technique at 1am . You sir are a life saver

    @javalos3655@javalos36559 ай бұрын

    • You're welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts9 ай бұрын

    • Used it again on the front breaks 😤 haha

      @javalos3655@javalos36559 ай бұрын

  • bravismo. that worked great. thanks!

    @krazy.88@krazy.8811 ай бұрын

    • You''re welcome !

      @screwsnutsandbolts@screwsnutsandbolts11 ай бұрын

  • That if F'ing class mate 👌 definitely doing it this way don't have the tool anymore and apparently never needed it. If you came up with this idea you're a genius

    @godblessyou9743@godblessyou97432 жыл бұрын

    • Thank you ! :)

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • I was about to lose my sanity..then I watched this video..worked great. Thank you

    @DDOAgaming@DDOAgaming Жыл бұрын

    • You're very welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Good ideas.

    @jamkpa@jamkpa3 ай бұрын

    • Thanks!

      @screwsnutsandbolts@screwsnutsandbolts3 ай бұрын

  • Thanks. Really helped me alot

    @patrikandersson703@patrikandersson703 Жыл бұрын

    • You're welcome!

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Omg worked like a charm just gotta be strong to do it😂

    @KilosFlo@KilosFlo Жыл бұрын

  • And thanks for helping

    @silasmar8352@silasmar835211 ай бұрын

  • Nice work!

    @AcuraJ32@AcuraJ3216 күн бұрын

    • Thanks!

      @screwsnutsandbolts@screwsnutsandbolts16 күн бұрын

  • Thank you, Sir/Ma'am!

    @FairladyZ1991@FairladyZ1991 Жыл бұрын

    • You're very welcome!

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Very creative and thank you for sharing your video. I really enjoyed watching the technique.

    @murryslims9695@murryslims9695 Жыл бұрын

    • You're welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Absolutely Good idea

    @kurniawanayyas6362@kurniawanayyas6362 Жыл бұрын

    • Thank you :)

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Thank you sir 👍🏾

    @sprayatwill@sprayatwill Жыл бұрын

    • You're very welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Great great tip pal. Thnx so much

    @mumtazzafar1576@mumtazzafar15762 жыл бұрын

    • No problem 👍

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • What a great idea!!! No need to buy any spreader tool especially to be used probably only once in my live. I know similar old school idea with two crowbars, but this is more efficient and safe. Crowbars can slip and make some dents to car body or damage the paint. Thanks

    @Zly-Porucznik@Zly-Porucznik Жыл бұрын

    • You're very welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • 😀thank you so much friend i really needed to learn this. 🙂🙂👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼

    @troytavarez3883@troytavarez38832 ай бұрын

    • You're very welcome !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • That helped me

    @besmart6063@besmart6063Ай бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • Absolute legend

    @abnwil3873@abnwil3873 Жыл бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • nice one!!

    @ltfkdk861@ltfkdk8612 ай бұрын

    • Thanks !

      @screwsnutsandbolts@screwsnutsandbolts2 ай бұрын

  • Thanks for the idea

    @MainGhoul@MainGhoul Жыл бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Thanks really helpful

    @jayclippers3592@jayclippers3592 Жыл бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • wow thank you so much 👍🏽

    @waveyting3788@waveyting3788 Жыл бұрын

    • You're welcome! :)

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • I compress calipers before pulling. Sometimes a pry bar works but I jus use a c-clamp

    @Wheelingoffthewrench@Wheelingoffthewrench Жыл бұрын

  • For whatever reason I couldn’t be bothered to think this through. I became irritated with myself for procrastinating on KZhead as a ‘shortcut.’ I got chills from the sound of chirping birds in the background as I understood that I was getting what I actually needed: self-compassion, gratitude, a still mind. Oh yeah, and the practical solution that I needed.

    @cleeguitar@cleeguitar Жыл бұрын

  • Thanks buddie!

    @jacobuskai4594@jacobuskai4594Ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • Well done bro..

    @ThomasNappo@ThomasNappo18 күн бұрын

    • Thank you !

      @screwsnutsandbolts@screwsnutsandbolts18 күн бұрын

  • Excellent video another TIP, remember to clean the rubber boot cover on the piston before you push dust and crud back into the pistons prolongs their life and prevent them seizing up

    @cassk9999@cassk9999 Жыл бұрын

    • Thank you, and thanks for the tip !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

    • Best thing to do is spray some silicone on the rubber dust cover before pushing it back in. Silicone will extend the life of the rubber cover.

      @frankhoward7645@frankhoward764511 ай бұрын

    • With what?

      @404SportzCardz@404SportzCardz9 ай бұрын

  • You're video saved the day, um now night lol could NOT get the AutoZone compression tool to work watch this helped me understand how the tool worked. Next time I'll save $60 rental fee and get a block of wood lol

    @jury1phok@jury1phok9 ай бұрын

    • You're welcome lol :)

      @screwsnutsandbolts@screwsnutsandbolts9 ай бұрын

  • This did the trick. The simple physics of leverage. Thanks a million bud.

    @silasfirsthand@silasfirsthand7 ай бұрын

    • You're welcome!

      @screwsnutsandbolts@screwsnutsandbolts7 ай бұрын

  • I just put an old break pad against the piston n use a c clamp works great only time I do it diff is when there screw in pistons then I use the tool for that

    @bradi5050@bradi505011 ай бұрын

  • Why didn’t I think of this! However, in my opinion, the bleed nipple should be opened to release the fluid displaced by the calliper piston as it’s pushed back. The reason? The fluid in the calliper is old and has been subject to a lot of heat so should be discarded. Also, as the fluid is pushed back into the master cylinder, it can occasionally push back the floating piston where it can stick because it travels into the unused part of the cylinder.

    @martinhann1672@martinhann167216 күн бұрын

  • Saved my ass after the kids lost the C Clamp and the car is already all apart with no ride to buy another one I appreciate you👍

    @timkayjr2958@timkayjr29582 жыл бұрын

    • You're welcome ! :)

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

    • Sameee

      @kaleabzenebe1407@kaleabzenebe14072 жыл бұрын

  • Your a life saver my brakes started grinding so I went to replace them realized I didn’t have a C clamp and thought I was screwed

    @nikosilvis4568@nikosilvis45683 ай бұрын

    • You're welcome, thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts3 ай бұрын

  • Excelent video, 👍👍👍👍👍👍😌😌😊 it is very usefull for me, i liked ir so much, thanks you so much i going to put on practice

    @oscaraguilar4024@oscaraguilar4024 Жыл бұрын

    • Thanks for watching ! :)

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • That's a nice method. I've always used a C-clamp and the old brake pad to compress the piston.

    @glennsampson5945@glennsampson59458 ай бұрын

    • Thanks !

      @screwsnutsandbolts@screwsnutsandbolts8 ай бұрын

  • Brilliant...

    @resistireland694@resistireland6944 ай бұрын

    • Thanks !

      @screwsnutsandbolts@screwsnutsandbolts4 ай бұрын

  • I’ve used a G clamp for this on many many vehicles… as it’s tightened by hand it’s very slow and gentle…

    @richardhampton4612@richardhampton46123 ай бұрын

  • My savior

    @bodiemitchell3091@bodiemitchell30914 ай бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts4 ай бұрын

  • Thank you so much man, very helpful 👍

    @steez23@steez23 Жыл бұрын

    • You're very welcome!

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Like that idea bro👍

    @jamesmartin7559@jamesmartin7559 Жыл бұрын

    • Thanks !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Nice trick and what about to do it the opposite way? After replacing the brake bads?

    @hectorontiveros7083@hectorontiveros70837 ай бұрын

    • Thanks. When you refit the pads and caliper, just press the brake pedal to push the pads back in contact with the discs.

      @screwsnutsandbolts@screwsnutsandbolts7 ай бұрын

    • @@screwsnutsandbolts oh ok thanks man

      @hectorontiveros7083@hectorontiveros70837 ай бұрын

  • Thank you!

    @eatwhatukiii2532@eatwhatukiii25322 жыл бұрын

    • You're welcome!

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • Excellent video

    @topautos@topautos2 жыл бұрын

    • Thank you very much! :)

      @screwsnutsandbolts@screwsnutsandbolts2 жыл бұрын

  • I met this Guatemalan guy who would come up with techniques like such, him growing up poor couldn't buy tools he had to figure things out with whatever he can come up with and improvised tools. He once patched my flat bicycle tire by just pulling the hole and tying it with 15 inches of waxed thread cord. That tired never leaked.

    @moisesr7840@moisesr7840 Жыл бұрын

  • very helpful

    @hanandezmuamaarr7809@hanandezmuamaarr780911 ай бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts11 ай бұрын

  • Life saver, made it work with boards an inch thick.

    @stickybonesg@stickybonesg Жыл бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Excellent hack!

    @094340@09434010 ай бұрын

    • Thanks !

      @screwsnutsandbolts@screwsnutsandbolts10 ай бұрын

  • Brilliant tips using the pieces of wood. Wood's better because they won't wreck the brake pads(if you plan to reuse them).

    @Johny40Se7en@Johny40Se7enАй бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandboltsАй бұрын

  • Thanks

    @lawrencemorgan3299@lawrencemorgan32999 ай бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts9 ай бұрын

  • Thank you sir

    @jomilez4731@jomilez4731 Жыл бұрын

    • You're welcome !

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Bravo!

    @souadsalhi550@souadsalhi55010 ай бұрын

    • Thank you !

      @screwsnutsandbolts@screwsnutsandbolts10 ай бұрын

  • VERY HELPFUL. THANK YOU SIR! THIS SAVES ME!!!!

    @kimex1989@kimex1989 Жыл бұрын

    • Glad it helped!

      @screwsnutsandbolts@screwsnutsandbolts Жыл бұрын

  • Thanks for the video. What size is the wood, 2x4?

    @greeneking77@greeneking773 ай бұрын

    • You're welcome. It was nearer to 1x2

      @screwsnutsandbolts@screwsnutsandbolts3 ай бұрын

  • Great video, very helpful tip , much appreciated

    @Retrobrownpaperbag@Retrobrownpaperbag7 ай бұрын

    • Thanks, You're very welcome !

      @screwsnutsandbolts@screwsnutsandbolts7 ай бұрын

  • ❤thank you i got it🙏

    @aminiasisegai2841@aminiasisegai28416 ай бұрын

    • Thanks for watching !

      @screwsnutsandbolts@screwsnutsandbolts6 ай бұрын
KZhead