How to Replace Front Forward Subframe Bushing 2008-2013 Nissan Rogue
Buy Now!
New Subframe Bushing from 1AAuto.com 1aau.to/ia/1ASFK06948
This video shows you how to install a front forward subframe subframe bushing on your 2008-2013 Nissan Rogue.
This process should be similar on the following vehicles:
2008 Nissan Rogue
2009 Nissan Rogue
2010 Nissan Rogue
2011 Nissan Rogue
2012 Nissan Rogue
2013 Nissan Rogue
Tools you will need:
• Pry Bar 1aau.to/oRV/1AXAA00020
• 20mm Wrench
• 12mm Socket 1aau.to/obpx/1AXAA00015
• 18mm Socket 1aau.to/oaeg/1AXAA00043
• 21mm Socket 1aau.to/oaeg/1AXAA00043
• Bushing Removal Tool
• Air Chisel 1aau.to/oby/1AXAA00270
• Ratchet 1aau.to/obw2/1AXAA00016
• Socket Extensions 1aau.to/obpx/1AXAA00015
• Torque Wrench 1aau.to/oaAX/1AXAA00044
• Anti-Seize Grease
• Chisel 1aau.to/okv/1AXAA00055
• Grinder
• Hammer 1aau.to/oSH/1AXAA00091
• Pole Jack
Subscribe: / @trq
Check out our playlist:
Nissan Rogue 2008-13 1st Generation: • Nissan Rogue 2008-13 1...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money
Thank you. My front bushings were completely ripped. There was a loud clunk noise as the vehicle either accelerated or slowed. To remove the old bushing shells, I heated the tube for about 2 min and used a hammer and chisel (big screwdriver) to hit all around the sleeve. Each bushing was about 7 min to remove. To install, I did not have the bushing install kit. You might be able to rent it from an auto parts store. Whatever you do, Don't try to pound it in with a hammer. At about the 8 min mark of the vid, you can see that technician cut a chamfer (is that the right word?) to get the bushing started. I cheated and since the subframe was out of the car, I took it to the shop and they installed for $50. Working in the driveway I used a jack to lift the subframe into place. This is a very helpful video. The most valuable part, for me, is the torque settings. All together, this was a $90 repair. Plan you work space, time and tools. This can easily be done in 4 hrs (hiccups and corrosion pending)
Some of the best instructionals on the tube
Tomorrow, I'm fixing my 2009 sentra subframe bushings and this video is making me very confident in what I need to do to replace it myself. Basically the same parts as a 2009 rogue since it's the same engine and transmission as in a sentra from the same year. And my cradle condition is very similar to the one in this video. Front forward bushings are shut and almost non-existent, and the bolts have the same amount of rust on them. I must say, you're pretty confident in taking those off without penetrating fluid first, good job for not having destroyed any bolts. I hope my repairs will be as simple as this video shows.
Thanks for the video It was very helpful
I really enjoyed watching this excellent how you show how it should be done
Thanks, very helpfull, Is ir absolutely necesary to removevthe lower ballboint?
Thank you so much,great video⭐⭐⭐⭐⭐
The amount of rust I would just replace the whole subframe.
Great video
Great video!!! Thanks!!
And repeat in 12months time, or 8 months in my case... OR buy poly bushes from PS Bushings in south africa and fit and forget :) the OEM type bushes aren't branded and it's impossible to tell the quality, I got mine from E bay and they didn't last, it's such a big job go for the PSB (problem solving bushings) one, you won't regret it :)
Is this called H beam bushings too?
7:58 do you need the bushing installation tool? can you just whack it with a rubber mallet?
May I know the name of the Bushing Removal Tool used in this film? Actually it was used for the installation of the new bushing. Thank you.
Where did you get the installation tool?
What is the took called to press the bushings in
Anyone know where to get the tool?
Like 🎉
Great info... can my issue be like subframe bushing ? sound is coming from my front wheel passenger side. kzhead.info/sun/iaeTncpvmp6oe58/bejne.html
You didn't show how you pushed the bushings into the subframe.