KZhead
Автокөліктер мен көлік құралдары

Soldering Stainless Steel - Oil Cooler Side Scoops 427 Cobra

Pete's Garage
2022 ж. 11 Нау.
14 716 Рет қаралды
Жүктеу

You can solder stainless steel parts as an alternative to welding. I requires the use of acid flux made specifically for soldering stainless steel.

Пікірлер

  • *Pete's Garage* Bravo well done, thank-you sir for taking the time to show us how its done. God Bless.

    @MrRebar15@MrRebar152 жыл бұрын

    • Thanks 👍

      @PetesGarage@PetesGarage2 жыл бұрын

  • Great video on soldering stainless. I've been searching for a solution for this for a long time.

    @burtreynolds3143@burtreynolds31437 ай бұрын

    • I was convinced that I needed to use a silver solder. I'm very surprized you were successful with regular lead free. I wish you'd shown the flux can because that flux seems to work well and appears to be the key.

      @burtreynolds3143@burtreynolds31437 ай бұрын

    • The flux is just an acid based flux for stainless steel, pretty easy to find

      @PetesGarage@PetesGarage7 ай бұрын

  • Thanks Pete for the very informative instructive lesson, very appreciative

    @thunderstruck5484@thunderstruck54842 жыл бұрын

    • Glad it was helpful!

      @PetesGarage@PetesGarage2 жыл бұрын

  • Very instructive and I appreciate the oft-repeated safety warnings.

    @jakklump@jakklump Жыл бұрын

    • Thanks my friend

      @PetesGarage@PetesGarage Жыл бұрын

  • Thanks for the video. Have used StayClean and Silver Bearing Solder for larger stainless to copper joints. But have a commercial sink project with 16 gauge and have to reattach the base of the divider. I'll probably use oxy with a small brazing torch to focus the heat and move quickly.

    @mxdev6387@mxdev63874 ай бұрын

    • That's really interesting

      @PetesGarage@PetesGarage3 ай бұрын

  • Thanks for the help. My Lincoln tig is down so might try this on a stainless tank.

    @curtmanley8336@curtmanley8336 Жыл бұрын

    • It will be pretty strong but not as strong as a weld

      @PetesGarage@PetesGarage Жыл бұрын

  • Thank you for this! Very informative!!

    @keystonekreative2174@keystonekreative2174 Жыл бұрын

    • You are so welcome!

      @PetesGarage@PetesGarage Жыл бұрын

  • What an interesting idea. Great demo and brilliant explanation. I've used this for my dog's collar, where my dog license inevitably gets lost. A few drops of solder on the metal clip and the license tag never comes off.

    @spelunkerd@spelunkerd2 жыл бұрын

    • It's a great alternative for those who do not have welding equipment

      @PetesGarage@PetesGarage2 жыл бұрын

  • Excellent video

    @howardharmon3451@howardharmon3451 Жыл бұрын

    • Thank you my friend

      @PetesGarage@PetesGarage Жыл бұрын

  • Nice work I appreciate the video

    @jimkillen1065@jimkillen10652 жыл бұрын

    • Thanks Jim

      @PetesGarage@PetesGarage2 жыл бұрын

  • Amazing! I had no idea you could do that! It's a shame...Frank missed a damn good video! LOL! Thanks Pete!!

    @littlejohnny4470@littlejohnny44702 жыл бұрын

    • Frank misses a lot...lol. Thank you

      @PetesGarage@PetesGarage2 жыл бұрын

  • That was so cool, Great vid Pete.

    @PeakyBlinder@PeakyBlinder Жыл бұрын

    • Thanks my friend

      @PetesGarage@PetesGarage Жыл бұрын

  • Hi Pete I'm building my second cobra and it's going to be a big block. My real concern about building the motor is determining the correct length of the push rods. I can build the bottom in install the crank put the heads on all that good stuff but I've never had to figure out aftermarket push rod length to get it just right. If you have a video on that that would be great. Otherwise I might have to give you a call once I save up enough money to get this going things sure have gotten expensive in the last year or two. Thanks

    @BKMDano17@BKMDano172 жыл бұрын

    • I'll try to make a video, but have many resources if you need help

      @PetesGarage@PetesGarage2 жыл бұрын

  • Thanks Pete

    @tracycolorado@tracycolorado2 жыл бұрын

    • Thanks!

      @PetesGarage@PetesGarage2 жыл бұрын

  • This is helpful.

    @kevinhornbuckle@kevinhornbuckle2 жыл бұрын

    • it's good if you do not have a welder

      @PetesGarage@PetesGarage2 жыл бұрын

  • I've welded on 6 inch columns and we had to preheat it up to 350 to 500 degrees and maintain that temperature we never turned off the rose buds then we had to put fire blankets

    @tinoflorentino3577@tinoflorentino3577 Жыл бұрын

    • This is solder, not weld

      @PetesGarage@PetesGarage Жыл бұрын

  • I believe there is a certain temperature in order to weld stainless and also maintain that temperature till finish

    @tinoflorentino3577@tinoflorentino3577 Жыл бұрын

    • This is solder, not weld

      @PetesGarage@PetesGarage Жыл бұрын

  • Will that stainless rust now that its been heated and had acid flux on it? Does it need to be painted afterwards?

    @Mrdubomb@Mrdubomb9 ай бұрын

    • No, you neutralize the acid with baking soda

      @PetesGarage@PetesGarage9 ай бұрын

  • Do your engine building videos relate to all builds regardless what motor or internals? Still follow the same steps and do it all the same way? I’m looking to get 900-1000HP with a boosted lq9 6.0. And I want to do it all myself.

    @FPS360VIDZ@FPS360VIDZ2 жыл бұрын

    • I try to make videos that show techniques that will apply to all engines

      @PetesGarage@PetesGarage2 жыл бұрын

  • I've also seen aluminum stainless and brass brazed together

    @tinoflorentino3577@tinoflorentino3577 Жыл бұрын

    • This is solder, not weld

      @PetesGarage@PetesGarage Жыл бұрын

  • Any reason not to do this with TIG brazing?

    @satamanschmidt3428@satamanschmidt34282 жыл бұрын

    • Nope

      @PetesGarage@PetesGarage2 жыл бұрын

    • This is for ppl that don't have welding equipment or just picking up a new hobby

      @tinoflorentino3577@tinoflorentino3577 Жыл бұрын

    • You can talk about safety stuff but some of us learn the hard way some ever the harder way

      @tinoflorentino3577@tinoflorentino3577 Жыл бұрын

  • I believe your wrong about copper copper takes a long time to heat up that's why there in 3 phases and high voltage machines

    @tinoflorentino3577@tinoflorentino3577 Жыл бұрын

    • This is solder, not weld

      @PetesGarage@PetesGarage Жыл бұрын

  • It's OK but solf​ ​solder..!!

    @guytiips3906@guytiips390611 ай бұрын

    • Lead free solder is very strong

      @PetesGarage@PetesGarage11 ай бұрын
KZhead