Hi everyone, Caleb here from Brownells. Today, I’m going to walk you through the basic maintenance steps for your Ruger 10/22, the BRN-22, and pretty much any Ruger 10/22 clone. This is crucial for keeping your rifle in top condition, so let's dive right in.
First and foremost, safety is key. Make sure your firearm is completely unloaded. Remove the magazine, pull back the bolt, and check the chamber to ensure there's no ammunition inside.
Once that's confirmed, let’s start the disassembly. Most Ruger 10/22 models just need one tool for disassembly - typically a screwdriver. You'll find a screw at the bottom of the stock, right in front of the magazine well. Depending on your model, this could be a flathead or an Allen screw. Unscrew this, but there's no need to fully remove it; just enough so that the barreled action can be lifted out of the stock.
Here’s a pro tip: make sure your safety is in the middle position during this step. If it's not, it might catch on the stock, making it difficult to remove the barreled action.
With the action free, let’s focus on cleaning the bolt and the receiver. If you have a factory setup, your buffer and pins might fall out easily, and that's okay. Just set them aside. For those with aftermarket parts, they might be tighter, and you may need a punch to remove them. Once the bolt is accessible, clean it thoroughly using a good solvent like Hoppes No. 9. Apply the solvent to a brush and scrub all parts of the bolt and the receiver, paying extra attention to areas with visible build-up.
To clean the barrel, we apply solvent to the brush and run it through a handful of times. Then, we can follow up with clean patches as well as oiled patches to clean and protect the bore.
For the trigger group, a simple wipe-down is usually sufficient for regular maintenance. It’s important to keep the hammer and the ejector clean since they play crucial roles in the firing process.
Lubrication is next. Apply a high-quality gun oil to all moving parts where metal contacts metal. This includes the bolt, the charging handle, and especially the face of the hammer, which rubs against the bolt when firing.
Once everything is clean and lubricated, it's time to reassemble. Reverse the disassembly steps, making sure everything snaps back into place correctly. Finally, conduct a function check to ensure everything is working properly. This means checking the safety, firing mechanisms, and making sure the bolt retracts and returns smoothly.
And that’s it! You’ve just completed basic maintenance on your Ruger 10/22. Regular maintenance like this will ensure your rifle continues to perform well and lasts for many years.
If you have any questions or additional tips, please leave them in the comments below. Don’t forget to like and subscribe for more tutorials like this. Thanks for joining me, and I’ll see you next time!
I got my first 10/22 as a kid for my birthday. Shot the crap out of it. Fast forward 20 or so years and I started to have light strikes. I thought maybe the firing pin broke, or perhaps just wore down so far over the years. While disassembling the rifle to investigate, I realized I had never done more than clean the bore and wipe down internal areas I could reach. I had never even removed the tigger group much less the bolt assembly. I had been worried that it was similar to the Mark pistol series which was notoriously finicky. So I dove in and fully disassembled it, discovering for the first time how easy it is to maintain. And also discovering 20 years worth of 22LR buildup crud that was causing my issues. Runs like a top again. Moral of the story: don't be afraid to tear into something. Videos like this are a godsend in that regard.
Bro got a casual AT4 chillin in his locker.
Nicely done video. I've had a 10/22 for over 40 years, cleaned it hundreds of times, but I watched the video looking to pick up tips! Thanks Brownells for doing these videos
Always learning.👨🏻🎓👩🏻🏫
Caleb. Suggestions for a new video similar to this. Takedown, maintenance, and reassembly of a Mark II Ruger pistol. (Unless you have as much problem as I do with the reassembly and can’t fit it in a 30 minute video.) I will understand. 😎
Outstanding instructional presentation! Most gun cleaning videos are aimed at folks who already know how to clean guns. Kinda like lawn mower repair videos are aimed at people who already know how lawn mowers work. Your video gives me some confidence I can get my new rifle taken apart AND put back together.
Wait a minute! Do you actually cut your grass?
the timing of this is amazing, i JUST picked up a 10/22 yesterday, and my name is Caleb too! Amazing video
Two things I do beyond what is here. #1 is remove the extractor and spring, using the "Gunsmither" tool from Tandenkross. The extractor slot often acquires a lot of .22 crud. #2 is to use the same "Gunsmither" tool for bolt reassembly. Seems to make it easier to keep the bolt and bolt handle properly aligned (and squared), while fiddling the bolt handle lug into the bolt recess.
Got my 10/22 when I was 12. I am now 54 and to be totally honest I have never torn it apart to clean it. I know, I am a terrible gun dad but truthfully I have never had a problem with it in all those years. Guess it is time to clean it lol.
Thanks, I use the Otis cleaning kit with cables that can be pulled through from the breach end on a couple of rifles I own that you can’t run a rod from the breach end.
Ruger 3+ decades ago (before YT) used to have training sessions on the 10/22 (and MkI) to show us how to clean, maintain, and trobleshoot the firearms. Here is a quick suppliment to help out, based on Ruger. 1- Barrel and chamber should be cleaned and wiped DRY before firing. 2- Bolt should be LIGHTLY oiled and wiped almost dry. 3- Receiver should be LIGHTLY oiled and wiped almost dry. Both of those recommendations from Ruger were to limit the powder fouling with blowback 22LR firearms. 4- Recoil spiring is cleaned and wiped dry while jamming charging handle. 5- The bolt and charging handle are assembled differetly at the factory and by gunsmiths for easier assembly. The charging handle goes further back, and light finger pressure at the breechface is used to insert the bolt. 6- Ruger will NOT say this truth. Don't remove the stock, unless you have to for super cleaning or gunsmithing work. The attachment screw and/or barrel band bend the barrel, differently each time the stock is reattached.
Yes, with a caveat that some have or do shoot the crap out of their 10/22s to point of needing to. I've bought a few over the decades. Two have shot actually hundreds of pounds of 22LR ammunition, to point of showing extensive wear. I don't recommend the take down model for accuracy. But I actually was handed it by the president of Ruger when I bought it on the anniversary of the 10/22 model.
I like the glass bottle of Hoppe's #9. I need one.
Why hasn't anyone made a Hoppe's #9 cologne??? Because yes it is almost everyone's favorite!!
Then, Sprinkle yourself with saw dust, and even manly men would find you attractive! 😂
LOL! My Ex-Wife hated the smell so much I couldn’t use it in the house. That should have been my first clue!
@@phillipleighton9641 I have a buddy who decided to propose to his GF when he caught her huffing his Hunters Specialty Fresh Earth cover scent wafters that he left out on the coffee table... Their wedding rehearsal cake was a replica of the scent wafer can... Keeper.
I’ve actually brought this up to my wife several years ago. She said not a good idea. So when I clean my guns I make sure to put a little behind the ears.
Coming from the army, the clp smell is etched in my brain. It reminds of so many things. It's funny while doing it not so fond, but now its better.
Great video, yes please do the video on drilling the back out.
I may try that too. Bore Snakes work without having to drill your receiver👍🏼
TIP: Differences in torque on the reciever skrew affect your point of impact and group sizes. Hence, have to rezero after cleaning.
I use a Hoppe's Viper Bore Snake for cleaning my Ruger 10/22's. That way I can still clean them from the chambers without having to have aftermarket receivers.
I have a small parts washer filled with parts cleaner fluid (mineral spirits) for gun cleaning. After washing i blow off the parts with compressed air. I clean the barrel with either a bore snake or cleaning rod like yours. I have a Bergara BXR Carbon I use for SCSA competition. It has the hole at the back of the receiver making using a cleaning rod easy. Periodically I attach a bronze brush to a modified cleaning rod connected to a drill to clean the carbon ring in the chamber. I do this rather slowly. I also use a right angle screw driver to align the charging handle to the bolt, making assembly very easy.
I just use a bore snake on mine now to avoid the muzzle.
BORE SNAKES ALL DAY BRO
My fathers idea of cleaning his 10/22 was drowning the barrel with bore cleaner and letting it run its course hahaha When I received his 10/22 the bolt almost wouldn't come out. The amount of buildup in it was insane!
My father's 10/22 lived a similar life. I wouldn't be surprised if I was the first one to clean it. He had it before I was born. The first time I cleaned it in the 90s. It's a early one from first few years of manufacturing.
@@DB-yj3qc He had a ruger mark ii. I know he wouldve broken it trying to reassemble it, im definitely the first one to clean that one too. It was gross lol
Decided to watch this video for tips, and then had to ask myself, Did I clean my 10/22 after the last time I used it? I guess I will be adding that to the to-do list
Another Great Video. Thank you!
I have great memories of the sent of hoppes #9 with cleaning guns with my grandfather years ago. a while back thought of making a cologne out of hoppes for gun guys🤩
Its funny that the first firearm I had was a G34, and now I feel like I missed out on Childhood memories. Can't wait for mine to get to my FFL this week! Thanks for the walk through, Caleb!
Great Job with All the details! Keep up the Great Work!
Very nicely done. Straight and to the point, but informative. Thanks for sharing. Stay safe and God bless
Please do a video for the “ Receiver Drilling Jig For Ruger 10/22” which you mentioned in the video Also item is currently out of stock so please restock as well. 👍
I always swab the bore with a dry patch when I'm done so lessen the chance of any cleaning agents pooling on the bolt face.
I just learned so much thanks
Loved this.
Thank you good info,😁
When I run my Dewey Rod thru the chamber end of the barrel, I always unscrew whatever attachment, brush, jag, slotted tip before I pull the rod back thru to avoid any possible chance of damaging the crown. I heard there was a tool to aid in replacing the charging handle and bolt into the receiver. Does Brownells have such a tool?
Great Video 💯💥💥💥💥💥💥💥
On the factory receiver, I drilled a 1/4" hole in the rear of it years ago. Simple to do, no special 'fixtures' needed, just measure twice - drill once. It's something Ruger should have done for us.
They have to sell it through the video
I have a Dewey R-1022-H rod guide that fits over the muzzle end of a heavy barrel 1022. It works, but I since drilled the receiver to allow cleaning from the chamber end.
The Ruger BX trigger won't go all the way to safe when the gun isn't cocked. So you can dry-fire the gun after making sure it's unloaded and the safety selector will stop at the halfway point.
Good video I might have worn some gloves maybe in the future you can do a spring refresh for extractor and firing pin showing upgrades available first time seeing the drilled hole someone was thinking i was always mindful crown but thought it was overblown
Magpul recommends 20 inch pounds in their paperwork for the stock
Holding that charging handle in place while putting the bolt back in was a real pain in the ass the first time I did it.
Try it with a Ruger mk.3 or earlier pistol.
Great video! Would recommend you make a suppressed 10/22 version though. It took me ages to come up with a regime that would allow for more than 100 rounds fired without the gun stopping due to fouling. Using Hornady dry lube instead of any other lubricants was what worked for me. Doing so allows me to go about 1K rounds without any cleaning.
Brownell’s used to see a guide to drill the hole in the receiver.
Good Video. What is the alternative buffer ? Is it preferable to the stock buffer ?
I use high pressure air to blow hoppe’s with dirt out of the receiver.
Video Request: Specifically how to clean the AR15's chamber area. You know, that hard as heck to reach area where the bolt lugs lock into? The star area? I can only reach in there with cue tips from a few angles, and through the ejection port. But one whole side I simply can't reach. And those silly foam star shaped things you can push in there and twist, don't seem to work that well. Am I making it too difficult for myself? Maybe the simple answer is take it into the backyard and hose it down with break free Powder Blast (or aerosol gun oil?) to get all the crud out? Let dry then spray in some ballistol?
nice ATGM !
New 10/22s the pins aren't just gonna fall out, they need a punch.
"Carefully guide it in" 😂😂😂😂 classic comment 😂😂😂😅
My father just recently bought the Ruger 10/22 magnum, I was wondering what your thoughts were on a recoil buffer pin for the .22 magnum?
Thats nice you sell the jig for the hole,,here is a way simple solution to avoid crown damage and brissel splash in the receiver,,,just slide the cleaning rod down the barrel when you see it in the reciever take and screw the brush on and pull it out take it off and repeat,,
What is your opinion on ultrasonic cleaners?
When the video got to the part where you were running the brush in from the breach. Seemed to be zipping that back into the barrel really fast! Is that not a concern for the possibility of crown damage?
Are you ever coming back to BR?
Did you seat the barrel in that stock or float it?
Just curious if there's gonna be any videos on the trigger group (or if I missed it) such as installing an extended mag release or that upgraded bolt catch that was in another video
Yes, there will be. We have them shot and are currently being edited. Thanks for watching!
@@brownells awesome thank you!
Those damned pins falling out of newer Rugers can be quite aggravating, particularly when it's the magazine latch pivot pin. Reassembly can be quite frustrating. I have found that putting a touch of grease on the pins will keep them in place.
The problem is that grease attracts and retains dirt and grit when can end up wearing the parts. That's why it's very rarely used unless absolutely necessary or in a sealed area.
@@_droid You don't have to put the grease on first. You can insert the pin and add a touch of grease to the outside. It will still hold the pin in place while you reassemble the rifle. Alternately, you can use a dab of oil instead of grease. Oil is what I applied last time.
Is that lever mag release an option from Ruger for the 10/22? Thanks!
Is that an AT4 on the safe box?
Why not remove the barrel from the receiver to push cleaning rod from the breach?
great video! I would like to watch a video explaining this procedure for the Hammerli Tac R1 22lr
Doesn’t everyone love the smell of number 9
How often do you need to strip your 10/22 like this?
I'm no expert, so this is a legit humble question: would it help protect the crown if you wrapped the brush with a patch, below the bristles? Or would adding more girth with a patch cause more damage or be more of a headache than it's worth?
Hi Caleb. I have always been under the impression that when you run your brush or jag down the barrel, you should only go breach to crown, and never in and out both ways. Whenever I clean a barrel, I make one pass, unscrew the brush or jag, carefully pull the rod out, put it back together and repeat. Am I tripping, or is there anything to this? Thanks. P.S. - I'm not OCD, but I am prior service.
That is addressed in the video.
Basically, if there is metal rubbing on metal, it requires oil. Just a schoosh!
Where can I get the oiling bottle that you are using? I could use several of those to help with so many different types of solvents and oils I use to break down, refurb, and rebuild old firearms. I looked on the Brownells website but couldn't find it.
Brownells sells them, look in cleaning category, I think they are called needle oilers they come 3 to a pack and have a plastic cap that slides on the end to seal the tip. Some solvents and oils really soften the rubber seal under the metal cap, so don't overtighten the cap because it will deform the seal it's best to keep them upright when your not using them. Don't just toss them in your range bag. But they are great for your shop bench. One more thing it's nearly impossible to keep any kind of marker or ink to stay on the bottles and don't even think about a tape lable. Other than that they are great.
@@tubeonline629 Thanks I was able to find them once I went into the cleaning section. I tried to look them up from the home screen and they wouldn't come up.
The takedown version is easier to clean
Pro tip: air your gun safe rocket launcher out monthly.
I have a very hard time believing Caleb is a gunsmith! His girly hands have NEVER seen a hard day's work!
Bonjour, a quelle fréquence doit on effectuer ce nettoyage ?
You only have to clean every 6 years. Lead is a great lubricant
The pins in my ruger were so tight i had to beat them out with a hammer and they did not want to come out after the hammering guess what it looks like now
Why would a training video about a specific firearm not use the specific firearm? Aftermarket parts are fine but he should have used a stock factory 10/22
Caleb alone doing a video alone of course on a .22 rifle? Check A 10/22 rifle? Check but wait why is it modern version? As a collector and restorer of the old .22 short, 22. rifle and .22 Long Rifle Rifles we all grew up and cut our teeth on,; that we came to know and love growing up. Wouldn't one of those of older 1960's 10/22 been better for the video? As they all need the same cleaning, if not even more from the years of kids not doing it fully as they should have. Plus Caleb could show off some of that great collection he brags about owning, protecting, rescuing , and preserving. Plenty of time to discuss the old beauties without Steve there interrupting the rabbit hole Caleb would of course go down....
Why are the clips so hard to load
I sold my .22 and I regret it so much..... Something I always will regret
You can get a stock one brand new for $299
Why do we call the Crown and Muzzle, the same thing?
The crown is a specific area of the muzzle. Kind of like the nostril is a specific part of the nose.
Allen wrenches are like USB plugs, you'll never get it right on the first try.
I'M SURE THE BROWNELLS RECEIVERS ARE NICE, BUT DANG THAT SOUNDS LIKE THERES SAND IN THE GUN WHEN HE SLIDES THAT BOLT BACK AND FORTH. SHOULD GET RID OF THE ANODIZING INSIDE AND POLISH.
Those 2 Allen screws on my 1995 10-22 that hold the barrel to the receiver continue to loosen. Always check and tighten those when I break it down. Is that a common problem?
Have you tried Loctite?
@@Joe-hz1nw don't use loctite just torque it down to 12 - 15 in/lbs.
@@Joe-hz1nw No, I just check it each time I clean it. Gives me an excuse to clean it.
I never clean my guns. When they stop working I just buy new ones.
Why did he start at the muzzel with the brush instead of the breach?
He was simply showing those who have to start from that end,he said from the beginning it’s best to go in front the chamber if you can..
We recommend watching the whole video as he cleaned it from the breach and briefly addressed how to clean from the muzzle. The standard 10/22 is not possible to clean from the breach with a solid rod without removing the barrel.
Buckshot , why don't you pay attention while watching a video? You know it's better to keep your mouth shut and appear ignorant rather than opening it and proving so.
@@edwardkawecki8101 Sounds to me like you need a girlfriend or do you prefer men?
Hoppe's shampoo and conditioner.🧔🏻♀️🧖🏽
No safety glasses?
_Patches do not need to come out white._ …thank you! As a kid cleaning guns was an ordeal because I’d been taught that. Probably explains why I love Glocks so much 😂