Wire rope doesn't close

Leave a slightly longer tail end, makes life easier, also a bit of tape on the strands stops them fraying so much

We call that a 'Flemish eye' but we use a 2 & 4 strand divide and fasten the ends with a bulldog grip. We use it in emergencies for a quick fix and normally use a Liverpool splice but there are many variations & mixed ways to splice. I was a trawler man but friend of mine was a rigger in the mines at Whitehaven England and it was magic how he managed those huge cables. There were no twisting machines then and when the came they made the job so much easier. It must be great to have brains!

Это опасная петля. И опасность в том, что она сразу не расплетается, она расплетётся позже и неожиданно, когда вы поверите, что она надёжная.

This is great, can you help me to check safe weight load for it?

We ran into this problem before. Try forming the eye from the middle. It push up the core as much. Hopefully that works.

Here's a tip for strand ends ...tape them up with electricians tape .wrap it to tighten strand anti clockwise...also good when cutting strands stops them opening

you can twist the strands back to its natural lay, after the lay is broken.

So many experts in the comment section. Oh my!

I make my Tails 1 Ft or so longer than the Eye ,Then do the Eye & wind the 2 tails into single line , Then Put the Eye in a Vice & take a tapered bar & Twist the Notch of the eye & Lay the Tail into the Standing Line & put on a a few Cosby Clamps - Quick & Easy

the smaller the eye and the thicker the wire, the sooner this type of splicing becomes a problem. the fact that the two ends had an overlap complicated things even more in this case.I always start intertwining the to pairs from the middle to the both ends. give the left a twist, then the right on etc...

I read all comments. Comment: cut the free hand of rope from the wooden reel. It was obvious from the first picture you started the video that will lead you wrong finish. When you separated strands 3-3 it was the second signal, first 3 strand was different lengths of position, .. etc .. etc,.. of course everyone knows what they are doing and of course you all know better than me !

Not a high enough helix in the strands. Make wire rope of a living and that looks like cheap imported rope. We check every rope every time we cut to make sure the helix is in spec for every rope we make. Told the cheap imported stuff don't go through the same quality checks.

It did it cause the 3 strands had to much gap between the wires. Set wire where it bends up n pick at 3 oclock open six times with core on right

the lay length of rope are wrong from the manufacturer..in others words that is called fly away..

just tie a granny not in it , that always works . :)

That's called a Molly Hogan loop

I really am not sure what the problem is here or even if there is a problem. Please explain someone what is going on.

Nice

That is a mess... that’s what happens with China Rope

you guys definitely do not know what you are doing.

Well, that didn't work.

Is that eye can worked well?? I don't think so.....

First, I think this cable is probably junk. Second, if you wound the core side in rather than the strand side, this would not happen. One more thing, Why does it take two people to do this?? I have done this for 35 years now and I can do 2" regular eyes.

you picked the wrong strands to work with was all. find the 12 o'clock point and go back 2

FFS they dont have a clue how to tuck wire rope that rope is 1 1/4 inch hard to handle, but they messed it up when they undone the strands!

i just play with it. you guys need more learning.

What you I need there's a big old bird nest

Te falto meter las puntas en mexico lo acemos mejor

bravo ti ga bato

soy estrobista.con 6 años de experiencia

Это не заплетение -это херня.Запелетение --это когда проколы делаешь/////

First off the lay on this rope is just not that good, second if you take more than 6 lays you should take 2 and 4 strands, however with this rope i would take 2and 4 anyway. Usually Chinese or American galvanized ropes have the worst lay preforms.

La costura FILIPINA

Cabo de aço 32 mm alma de aço pré-formação 6 por 25.

out of lay core wire is worng

32mm

Teen years experience I need work

now when some one dies or something is damaged because of subpar material, you're to blame...not the manufacturers...should have went with German or Japanese...

Sorry maybe i have had to splice too much junk rope . There is definatly a rope issue but your splicing technique exasperated the problem . If you take the 3strand side and get it started on the core side of the crotch it will keep the core from slipping in as you wind the eye. As soon as you locked the core side you could see the slip and should have unlocked and switched sides. But seeing as you did notnhave a sleeve on the cable i am guessing this was just a test ;)

so what now ?

ອ່ອນ

Wrong Wrong Wrong !!!

The wire rope it is not of the best quality

AMATEURS

why？ look like project fail.....

This is not compleat vdo

cheap chinese wire :D

wrong

too many ppl I made 15 dollars a hr. doing by myself I'm 6 5. in 355 lbs 💪😁

boring boring!!!!!!!