Check out this incredible device, Wire bender for making lures
Пікірлер
Very nice and clean! 👌
@taymot21312 ай бұрын
Go buy a valve core tool from your local parts store and start with half the tool already made 😊
@pattywaller189329 күн бұрын
Nice videos 🎉
@TNR_FISHING_VIDEOS7 ай бұрын
You are a genius
@amazing40s972 ай бұрын
Simple et efficace 👏👍 Merci 🎉
@brunoblanc9883Ай бұрын
Could you build something like this for 12ga wire but also put a nitroset clip in the loop and use a hand drill driver?
@jeremypremeau6856Ай бұрын
Gostei é simples e facil de fazer ✌️✌️✌️
@flaviobarbosa6778Ай бұрын
❤❤❤ GRAZIE ❤️❤️❤️
@MARTIN-ez2xh7 ай бұрын
Which wire size are you using? my loops came out awful and it might be because I'm using a softer wire (20lbs)
@ProducerDeejaySonic4 ай бұрын
Corde à piano obligatoire 😊
@gerardgoubel416913 күн бұрын
Gostei deste método bem mais simples e
@moisesjacinto63192 ай бұрын
볼트 🔩 만들수이서요?
@user-sj6wd8xf8qАй бұрын
How to For wire 0.4mm
@abyansyah406129 күн бұрын
Ačiū už patarymus,,, za trudi ne gliadia laik
@remigijusdriukas20947 ай бұрын
safety first!!!! be carefull, you could do all that with stationary equipment and with safety!
@NikosRitzakis4 ай бұрын
👍👍❤❤
@poissonnord54817 ай бұрын
You could sell those. 🤘🏻
@ChasingGrounders_8 күн бұрын
Взял отвёртку изнахратил 😂
@akmafishing9077 ай бұрын
Its cool to invent, create your own homemade things, but the Time, Effort, and Tools needed...., I personally Would just get an Inexpensive Wire bending loop Tool. But agree.... There is personal Satisfaction Making it yourself.
@eugenegress58962 ай бұрын
😮
@charlesmesserschmidt8026 ай бұрын
Very cool ideas but please if you try this use a vice or brace it on a table at least to protect your fingers when using a saw like this . I’d hate for someone to follow these instructions and have that saw skip over into their fingers .
@mikeylikesit6622Ай бұрын
Faut pas avoir peur des mouches😊
@gerardgoubel416913 күн бұрын
It's a good idea, but... the 'know how' is very dangerous! É uma ótima ideia, porém a forma como fez o corte não é nada recomendável, é muito inseguro.
@osvaldojunior1984Ай бұрын
Как ещё пальцы целы?
@user-mn2bz7cg9s3 ай бұрын
А в чём проблема эту накрутку сделать с помощью тех же круглогубцев и пальцев рук ну или в крайнем случае плоскогубцев и круглогубцев
Very nice and clean! 👌
Go buy a valve core tool from your local parts store and start with half the tool already made 😊
Nice videos 🎉
You are a genius
Simple et efficace 👏👍 Merci 🎉
Could you build something like this for 12ga wire but also put a nitroset clip in the loop and use a hand drill driver?
Gostei é simples e facil de fazer ✌️✌️✌️
❤❤❤ GRAZIE ❤️❤️❤️
Which wire size are you using? my loops came out awful and it might be because I'm using a softer wire (20lbs)
Corde à piano obligatoire 😊
Gostei deste método bem mais simples e
볼트 🔩 만들수이서요?
How to For wire 0.4mm
Ačiū už patarymus,,, za trudi ne gliadia laik
safety first!!!! be carefull, you could do all that with stationary equipment and with safety!
👍👍❤❤
You could sell those. 🤘🏻
Взял отвёртку изнахратил 😂
Its cool to invent, create your own homemade things, but the Time, Effort, and Tools needed...., I personally Would just get an Inexpensive Wire bending loop Tool. But agree.... There is personal Satisfaction Making it yourself.
😮
Very cool ideas but please if you try this use a vice or brace it on a table at least to protect your fingers when using a saw like this . I’d hate for someone to follow these instructions and have that saw skip over into their fingers .
Faut pas avoir peur des mouches😊
It's a good idea, but... the 'know how' is very dangerous! É uma ótima ideia, porém a forma como fez o corte não é nada recomendável, é muito inseguro.
Как ещё пальцы целы?
А в чём проблема эту накрутку сделать с помощью тех же круглогубцев и пальцев рук ну или в крайнем случае плоскогубцев и круглогубцев
Are you actually that poor???