From a retired old welder, thanks for posting this. Wish I had this when teaching.
@TrollworksForgeАй бұрын
Cool ! I have wondered how tank welders manipulate the alignment & spacing of the plate seams. Now I understand. The "blank nuts are welded on 1st, giving something for the pin & wedge jig to place force against! Thanks for sharing that.👍
@PaulThomas-qo9vy2 ай бұрын
Miss ko n rn ang mag fitt up ng plate...im also a plater before in subic shipyard brder ..like side shell .bottom plate repair .thnks for sharing hope it will help us to have a idea hpw to use your special tool in plate fitting ..God bless brader..more vdeos pls.
@steeljas454011 ай бұрын
Thanks your comment much appreciated. Just keep pray to GOD
@welderausphil11 ай бұрын
Just cut a notch out of a piece of scrap plate that a wedge can fit inside so when it’s welded on one side it overhangs the butt weld area so both side can be brought level , tack them and then knock the plate off and move up to the next area! You now have your PLATE DOGS !!!!
@Then.722 ай бұрын
You can move your plates any direction using a key plate. Up down tighten your gap up loosen it up raise and lower each side and keeps your tank round a dog won’t do that. You keep pins in while your welding to keep it from sucking in/out
@robertboyle26212 ай бұрын
@@robertboyle2621 I don’t think you understand if you think you can’t use them in any direction
@Then.722 ай бұрын
@@Then.72u really don’t get it do ya?
@chauncey59622 ай бұрын
@@chauncey5962 explain why because I think you don’t understand how to level two pieces of steel plate nor do you know what Plate Dogs and a wedge are in Fabrication !
@Then.722 ай бұрын
@@chauncey5962 still for your explanation?????
@Then.722 ай бұрын
Your Contents are very informative keep on posting .God bless
@isaganicruz75888 ай бұрын
The sounds inside that tank are really interesting........almost like a Ennio Morricone 'Spaghetti Western' sound track......
@ypaulbrown10 ай бұрын
Thanks your comment much appreciated
@welderausphil10 ай бұрын
Bravo...well done, cheers from Florida, USA, Paul
@ypaulbrown10 ай бұрын
Thanks your comment much appreciated from Florida , USA,GOD BLESS
@welderausphil10 ай бұрын
Congratulations on the technique.
@jmarcelopacheco10 ай бұрын
Thanks your comment much appreciated.
@welderausphil10 ай бұрын
Excellent explanation, thank you very much
@rodolfocuero94586 ай бұрын
Thanks your comment much appreciated
@welderausphil6 ай бұрын
Nice and good job 👍
@waeltaha98277 ай бұрын
Thanks your comment much appreciated
@welderausphil6 ай бұрын
Nice. And good job
@priyohalder11 ай бұрын
Thanks you comment much appreciated
@welderausphil11 ай бұрын
Good job
@jawedali266911 ай бұрын
Thanks your comment much appreciated.
@welderausphil11 ай бұрын
Very cool, true, flush, and gap, I can use elements of this technique in the mining equipment I work on, kind of like dogging in three directions at once
@thomasmharris5 ай бұрын
Yhanks your comment much appreciated
@welderausphil5 ай бұрын
Thanks your comment much appreciated
@welderausphil5 ай бұрын
Great
@engasaadadnan84508 ай бұрын
Thanks your comment much appreciated
@welderausphil7 ай бұрын
Hello, do you have dwg projects of the equipment?
@MegaChelaz6 ай бұрын
Yes Thanks your comment much appreciated
@welderausphil5 ай бұрын
Teknik yang bagus bro
@fath137411 ай бұрын
Thanks your comment much appreciated
@welderausphil11 ай бұрын
Took me a while to see how that works but it’s pretty tidy
@WineScrounger Жыл бұрын
Thanks your comment much appreciated.
@welderausphil Жыл бұрын
abrasive round gauge blocks and ferrous cones. Its life jim but not as we know it. Sir if I may ask, what chirality and how many strands are your genetic chains? Triple helix left handed?
@cdrom107010 ай бұрын
Chirality is a concept that arises in the field of chemistry ,specifically in the study of molecules and thier three- dimensional structures.In other words , A Chiral object or molecule can not be perfectly aligned with its mirror image , no matter how the two are oriented. Genetic chains , specifically refering to DNA ,typically consist of two complementary strands that are arranged in a double helix structure. Each strand is composed of a sequence of nucleotides, which are the building blocks of DNA Thanks your comment much appreciated.
@welderausphil10 ай бұрын
@@welderausphil great reply to a heckler.....cheers
@ypaulbrown10 ай бұрын
Is this a traveling job?
@joshhathaway27916 ай бұрын
Yes Thanks your comment much appreciated
@welderausphil6 ай бұрын
What was the thickness of metal to be welded
@waqasmuneer79514 ай бұрын
6mm thanks your comment much Appreciated
@welderausphil4 ай бұрын
@@welderausphil can I use this method for 20 mm thickness tank?
@waqasmuneer79514 ай бұрын
@@waqasmuneer7951 No , not almost the same but a bit different. 20 mm More strong back inside tank specially in bottom section ,before erection of shell plate and Make sure the acurancy ,different welding process submerge arc welding and AGW welding for vertical ,stick welding ,flux cored gasless welding on the bottom ,content of tank like liquid fertilizer tank that i have experinced 20mm thickness shell plate . The video u have watched was leach tank that’s why is thin. 2nd shell plate ,no more welding tack on the gap .full welded the u plate instead tacking in the gap after that fit up .the AGW machine welding the vertical position .a bit different . Thanks your comment much appreciated
@welderausphil4 ай бұрын
solda muito ruim mnoBrasil não passa acoplamento otimo
From a retired old welder, thanks for posting this. Wish I had this when teaching.
Cool ! I have wondered how tank welders manipulate the alignment & spacing of the plate seams. Now I understand. The "blank nuts are welded on 1st, giving something for the pin & wedge jig to place force against! Thanks for sharing that.👍
Miss ko n rn ang mag fitt up ng plate...im also a plater before in subic shipyard brder ..like side shell .bottom plate repair .thnks for sharing hope it will help us to have a idea hpw to use your special tool in plate fitting ..God bless brader..more vdeos pls.
Thanks your comment much appreciated. Just keep pray to GOD
Just cut a notch out of a piece of scrap plate that a wedge can fit inside so when it’s welded on one side it overhangs the butt weld area so both side can be brought level , tack them and then knock the plate off and move up to the next area! You now have your PLATE DOGS !!!!
You can move your plates any direction using a key plate. Up down tighten your gap up loosen it up raise and lower each side and keeps your tank round a dog won’t do that. You keep pins in while your welding to keep it from sucking in/out
@@robertboyle2621 I don’t think you understand if you think you can’t use them in any direction
@@Then.72u really don’t get it do ya?
@@chauncey5962 explain why because I think you don’t understand how to level two pieces of steel plate nor do you know what Plate Dogs and a wedge are in Fabrication !
@@chauncey5962 still for your explanation?????
Your Contents are very informative keep on posting .God bless
The sounds inside that tank are really interesting........almost like a Ennio Morricone 'Spaghetti Western' sound track......
Thanks your comment much appreciated
Bravo...well done, cheers from Florida, USA, Paul
Thanks your comment much appreciated from Florida , USA,GOD BLESS
Congratulations on the technique.
Thanks your comment much appreciated.
Excellent explanation, thank you very much
Thanks your comment much appreciated
Nice and good job 👍
Thanks your comment much appreciated
Nice. And good job
Thanks you comment much appreciated
Good job
Thanks your comment much appreciated.
Very cool, true, flush, and gap, I can use elements of this technique in the mining equipment I work on, kind of like dogging in three directions at once
Yhanks your comment much appreciated
Thanks your comment much appreciated
Great
Thanks your comment much appreciated
Hello, do you have dwg projects of the equipment?
Yes Thanks your comment much appreciated
Teknik yang bagus bro
Thanks your comment much appreciated
Took me a while to see how that works but it’s pretty tidy
Thanks your comment much appreciated.
abrasive round gauge blocks and ferrous cones. Its life jim but not as we know it. Sir if I may ask, what chirality and how many strands are your genetic chains? Triple helix left handed?
Chirality is a concept that arises in the field of chemistry ,specifically in the study of molecules and thier three- dimensional structures.In other words , A Chiral object or molecule can not be perfectly aligned with its mirror image , no matter how the two are oriented. Genetic chains , specifically refering to DNA ,typically consist of two complementary strands that are arranged in a double helix structure. Each strand is composed of a sequence of nucleotides, which are the building blocks of DNA Thanks your comment much appreciated.
@@welderausphil great reply to a heckler.....cheers
Is this a traveling job?
Yes Thanks your comment much appreciated
What was the thickness of metal to be welded
6mm thanks your comment much Appreciated
@@welderausphil can I use this method for 20 mm thickness tank?
@@waqasmuneer7951 No , not almost the same but a bit different. 20 mm More strong back inside tank specially in bottom section ,before erection of shell plate and Make sure the acurancy ,different welding process submerge arc welding and AGW welding for vertical ,stick welding ,flux cored gasless welding on the bottom ,content of tank like liquid fertilizer tank that i have experinced 20mm thickness shell plate . The video u have watched was leach tank that’s why is thin. 2nd shell plate ,no more welding tack on the gap .full welded the u plate instead tacking in the gap after that fit up .the AGW machine welding the vertical position .a bit different . Thanks your comment much appreciated
solda muito ruim mnoBrasil não passa acoplamento otimo
Obrigado seu comentário muito apreciado