KZhead

Epoxy Resin Art Pour Painting

Andy's Art Lab
2023 ж. 31 Там.
38 859 Рет қаралды
Жүктеу

Ready for some relaxing resin pouring? In this video I did away with any instructions to go with it and just left it as a video to watch and to enjoy some relaxing music. I will make an epoxy resin art for beginners video that will talk through these steps so if that is of interest give my channel a follow :-)
FREE GUIDE: If you are considering taking up resin art as a hobby, or even a side hustle then grab my FREE guide on Resin Basics for Beginners on my website andysartlab.com
-------------------------------------------------------------------------------------------------------------------------
🖌🎨 ART SUPPLIES 🖌🎨
Resin: amzn.to/46ApieL
Resin Molds: amzn.to/3OhoT8z
Resin Dye: amzn.to/3DGvjcC
Measuring Cups amzn.to/43RbLgb
Alcohol inks amzn.to/3DGvjcC
Mica Powder amzn.to/3YpNVHd
Glitter amzn.to/3YpNVHd
Foil amzn.to/3Qnmxrn
Natural materials amzn.to/43Rghew
Pressed flowers etc amzn.to/43Rghew
Acrylic Supplies: amzn.to/3XyHUYi
Silicon for Molds: amzn.to/3PFNKFn
Vacuum Pot only: amzn.to/44eTTgo
Vacuum Pot and Pump: amzn.to/3pqr5SX
Pressure Pot: amzn.to/3JGgU3f
SAFETY EQUIPMENT:
3M Half Mask amzn.to/44X7n0w
3M Organic Vapour Filter amzn.to/45kEBH1
3M Eye Protection Goggles amzn.to/3OnMbJR
Nitrile Gloves amzn.to/3s4QkLy
-------------------------------------------------------------------------------------------------------------------------
✨🎇 FOLLOW ME ✨🎇
Tik Tok: / andysartlab
Twitter: / andysartlab
Instagram: / andysartlab
Web and Blog: andysartlab.com
Newsletter: zaap.bio/andysartlab
-------------------------------------------------------------------------------------------------------------------------
🔧🔨SOFTWARE I USE 🔧🔨
Link in Bio: 10% Off code 'zaap10' zaap.ai/?ref=andysartlab
Boarderless Banking: Wise wise.com/invite/ath/andys99
Social Media Content Re-purposing: neon.ly/repurpose
Email Marketing: neon.ly/aweber
VPN: SurfShark: neon.ly/surfsharkoffer
KZhead Optimization: www.tubebuddy.com/nftiethings
--------------------------------------------------------------------------------------------------------------------------
DISCLAIMER
These videos are for entertainment purposes only. Follow manufacturer instructions and always wear PPE when dealing with chemicals like resin. Some of the above links contain affiliate products where we make a small commission, but at no additional cost to you.

Пікірлер

  • very interesting art

    @arpanbhatt3335@arpanbhatt33355 ай бұрын

    • Thank you so much 😀

      @AndysArtLab@AndysArtLab5 ай бұрын

  • I’m just starting in epoxy resin. I really hope to reach that caliber someday. Question, how much does that design table now sell for? Round figure is fine.

    @josephpoitras3090@josephpoitras30906 ай бұрын

    • Thanks very much. It looks harder than it actually is. You just need to start doing these art pours and you will get to know what works. I These sell for around the $100 + $150 USD figure.

      @AndysArtLab@AndysArtLab6 ай бұрын

  • I do pour painting and I’ve never seen anyone trying to blow the design out with a heat gun , the heat gun is only used to pop the bubbles , people usually use the hair dryer then let it dry before applying resin to protect the design

    @daze8585@daze85852 ай бұрын

    • Thanks for watching. You are correct a heatgun is great at removing air bubbles. I find with a fast cure resign if its starting to cure while pouring the extra heat the heat gun provides over a hairdryer makes it a bit more viscous again to blow it a little further. I find that you have a little more control with a heatgun over a hairdryer in pushing the hotair as well, however I use a hairdryer at times as well.

      @AndysArtLab@AndysArtLab2 ай бұрын

  • Where can we get these MDF rounds???

    @JudyKritikos@JudyKritikos5 ай бұрын

    • I made mine and have a video on my channel how to make them if you have a router. You can buy them from some art supply places as well.

      @AndysArtLab@AndysArtLab5 ай бұрын

  • Bellissimo davvero quanto è spesso il pannello? Grazie se mi risponde

    @gabriellaragona3897@gabriellaragona38975 ай бұрын

    • Thank you 😍 The panel is 18mm thick.

      @AndysArtLab@AndysArtLab5 ай бұрын

  • Sir, is there any such chemical available that if a design is made on a wet cloth with a roller, it will remain the same?

    @mohdjabir6828@mohdjabir68283 ай бұрын

    • If the cloth was stuck to some kind of backing like wood then you could coat it in Epoxy Art Resin and it would protect it. You would have to watch for airbubbles and use a blue flame to pop them.

      @AndysArtLab@AndysArtLab3 ай бұрын

  • Hocam merhabalar ben de bu işi yapmaya başladım ama kenarları sizin gibi olmuyor nerede hata yapıyorum sehpanın kenarları açık kalıyor

    @ibrahimaktan5421@ibrahimaktan54212 ай бұрын

    • Thank you for your comment. First you need to tape the underside with painters tape to make sure you can remove any drips once it's dry. Next you need to make sure that it's 100% level so the resin runs off the edge evenly. If you have gaps you can run your gloves hand around the edge to make sure it's all covered with resin. I hope this helps.

      @AndysArtLab@AndysArtLab2 ай бұрын

    • Teşekkürler hocam

      @ibrahimaktan5421@ibrahimaktan54212 ай бұрын

  • What us This wood name?

    @SehrishNawaz-ki3iz@SehrishNawaz-ki3iz6 ай бұрын

    • The wood is called MDF: Medium Density Fibreboard. Its an engineered wood and its cheaper than plywood.

      @AndysArtLab@AndysArtLab6 ай бұрын

  • Buenas noches pueden explicarme en español por favor gracias me gustaría hacer un cuadro

    @epalminedesmancilla956@epalminedesmancilla9564 ай бұрын

    • Escribiré una entrada en el blog esta semana sobre cómo hacer una pintura de resina para ti.

      @AndysArtLab@AndysArtLab4 ай бұрын

  • Sar chemical k naam batao

    @SaleemSaleem-ts2gf@SaleemSaleem-ts2gf4 ай бұрын

    • Sorry I was unable to translate your comment. Are you able to put it in English if possible?

      @AndysArtLab@AndysArtLab4 ай бұрын
KZhead