【加工動画56】旋盤でV溝/How to cut a V groove with a lathe
2024 ж. 25 Сәу.
21 050 Рет қаралды
旋盤で端面にV溝を削りました。
安全に留意してアイデアの種にしていただけたら幸いです。
00:07 快段目盛15cmスケール(定規):amzn.to/3EoY8L0
04:15 チップソー(110mm): amzn.to/3vqTf2W
背景音楽/BGM: New Land - ALBIS
撮影機材:amzn.to/3bNBj5D
使用した旋盤/Lathe model: ワシノ/Wasino LRS-55A
背景音楽/BGM: New Land - ALBIS
We would appreciate it if you could use it as a seed for your ideas after considering safety.
I don't understand a lick of Japanese writing, but this is easily one of my most favorite channels.
Спасибо за познавательные уроки! Ваш стиль работы приносит огромное удовольствие!
Здравствуйте ваши возможности использовать станок поражают😊
You can't be a Machinist! Your hands are too clean😊 Appreciate the Videos. 👍🏻
Спасибо за видео. После обработки диском, пришлось немного править поверхность?
Спасибо за просмотр. При обработке стружкорезом поверхность будет слегка волнистой, но если требуется точность, то придется дорабатывать бокорезом.
ОГО! Александр, здравствуйте!
Он точно вытачивает и собирает по деталям второй станок, помяните моё слово!)
I did one V on my homemade lathe too, it work good and nicely comfortable and helps me a lot work. Thanks😊😊😊
I always love watching the set up. You can always tell when someone knows what they're doing based on that! Your set ups are immaculate! When you set the saw blade up in the chuck, do you have to put the part on center?
Thank you for watching. The parts were fixed in the center. If the part is too low, the part will be pulled by the cutter and the backlash will be removed all at once, potentially damaging the cutter.
Leave it to the Japanese to design a scale that is so easy to read!!
Very good job, thank you
Master of machenist👍🏼👍🏼
❤ very nice arigatu
Похоже на поджимной сухарь рулевой рейки ваз 1118
👍
Bom dia do Brasil.
👏👏👏🤩🤩🤩
Is this going to be jaws for home made large tap wrench?
Thank you for watching. This part was fabricated for demonstration purposes. It's perfect for the kind of use you mention.
@@SwaplampJapan Yes you would need to thread the end and mill some flats ,maybe harden the jaws as well but it would make fine tap wrench that holds tap straight.Maybe a future project?
@@zumbazumba1 thank you for your reply. I currently have no plans to make a tap wrench, but I may do so in the future.
А куда патрон kitagawa делся?
Спасибо за просмотр. На днях я добавил УЦИ в различные части станка, оснащенного патроном Китагавы, сделав его непригодным для видеосъемки. Этот токарный станок в настоящее время оснащен очень старым патроном Кобаяши. Этот патрон также имеет большой диаметр проникновения, что упрощает его использование.
Диск отогнулся при резе, поверхность кривая - нет не пойдет такое! Жесткость диска никакая.