Should have put the cylinder sleeves in the freezer as well..
@sailaway101510 ай бұрын
Doubt shop has refrigeration
@peted521710 ай бұрын
@@peted5217 when I've done similar interference fits on tooling in the shop just using the lunchroom freezer. It's feasible, freezers are set to -18°C( -0.4°F), cold enough to reduce dimensions a few thousands. Plus heating the block, should drop right in.
@sailaway101510 ай бұрын
Ты думаешь они это не сделали?
@user-sd9jr3po2k10 ай бұрын
They should have had hot ice 🧊 at least mostly most shop for have it, we do.
@eliezerramosjr101710 ай бұрын
@@user-sd9jr3po2kThey clearly did not. The exterior color of the sleeves should have frosted when coming near the heated metal. Condensation, it's why you heat or cool, but not both.
@Pandaoniman10 ай бұрын
Дайте адрес,чтобы туда не ездить.
@user-vb6me4np4r10 ай бұрын
@@Dark_Stalker404 ахахахах
@miramistin477010 ай бұрын
Только хотел написать😂
@user-ql1il5zo7w10 ай бұрын
🤣🤣🤣🤣
@excavator-operator10 ай бұрын
@@Dark_Stalker404в Пакистане без перчаток работают 😂
@user-ce1lb3ss4l9 ай бұрын
@@Dark_Stalker404qp
@ibrahimadoumbaya42359 ай бұрын
Note to self: Never go there for engine repairs
@lala123abc9 ай бұрын
Put the liners in the deep freeze overnight and they will slide in or very little hammering.
@michaelcuff341810 ай бұрын
No Don't Hammer Put the cylinder sleeves in to liquid Nitrogen Cold shrinkage then insertion
@boboften995210 ай бұрын
You're assuming this third world "garage" has money for things that make sense...?
@shawnhuk9 ай бұрын
No definitely a rubber mallet and a wood block
@chrishall16929 ай бұрын
Liquid nitrogen? You mean dry ice?
@notstewie51038 ай бұрын
Liquid nitrogen? Good luck finding out if they have 24/7 electricity
@jeffsafawi794721 күн бұрын
Гильзы должны входить от небольшого усилия, ну никак от кувалды, .. Капец двигателю....
@user-if5cl4pi4j10 ай бұрын
Это ,, сухие" гильзы. На дизеле болгарского погрузчика такие гильзы ставили прессом, при этом грели блок двумя паяльными лампами.
@user-pg7ml4jh9p9 ай бұрын
@@user-pg7ml4jh9pзначит нужно было охладить гильзы и они бы в блок просто упали.
@dmitrbondar78149 ай бұрын
@@dmitrbondar7814 Гильзы тонкостенные, даже если их где-то как-то охладить, они быстро нагреются. Да и охлаждать их было негде.
@user-pg7ml4jh9p9 ай бұрын
I worked in a parts house with a machine shop, they would put the sleeve in dry ice for about half hour ,and use white lead to lubricant and pull it in with a air wrench and a threaded puller, and didn’t heat block,
@robertspeschel986810 ай бұрын
Well you just added 40k worth of miles to those cylinders and it hasn't even been rebuilt yet.
@solominded9 ай бұрын
Не правильно. Нагрев бесполезен, если так заталкивать.
@Zampolit201210 ай бұрын
Здесь должен быть жидкий азот.
@tayumajazz457010 ай бұрын
Да, охладить гильзу
@dimasemenov532910 ай бұрын
Кого ты лечишь мастер 🧐🧐🧐 они спецы 🤣🤣🤣🤣🤣🤦♂️🤦♂️🤦♂️
@excavator-operator10 ай бұрын
Здесь даже пропана будет достаточно.
@dmitrbondar78149 ай бұрын
I used dry ice on the liners and they just fell into the bore
@johnbollok55869 ай бұрын
Dry ice work better my friend or a deep freezer do the work
@joselitorosario307310 ай бұрын
Those idiots are ruining the engine. After the partial heating the block is crooked and will go to waste.
@sc1petrol10 ай бұрын
Would of been even better if you removed the locating dowels for the head and cleaned up the block face before fitting the liners because the flame rings on the liners protrute a few thou to seal the gasket and you got next to no show cleaning it properly once liners are in.
@stephengibbs437210 ай бұрын
Remarkable technique!
@user-ob6yf5nm1w16 күн бұрын
Уважаемые че Вам слабо сделать приспособу для постановки ГИЛЬЗ в блок, а это очень просто
@valmak869610 ай бұрын
Сразу видно мамтны умельцы
@xxxyxxxy748310 ай бұрын
Fhffh
@durgeshsahudurgeshsahu65310 ай бұрын
Definitely a Honda mechanic
@stephenhans1892 ай бұрын
Так ведёт блок бумерангом ! Его надо сразу весь греть ! Или гильзы азотам Эта Не ремонт .простите а филькина грамота !
@user-jp7ge1ru9l10 ай бұрын
Все верно дизель М400 гильзы сажают с азотом
@user-kx4nk8lf3oАй бұрын
도대체 누구한테 배워서 이런 영상을 올리는거야 옛날 옛날 구형차에만 그렇게 작업하거라. 뭐 요즘 신형차들은 엔진 보링할일은 없겠지만....
@bbomulsum8 ай бұрын
Как на заводе. Говорят они😂😂😂. Прямо по технологии!
@Sayga_45Rus10 ай бұрын
Гильзы полопаются во время работы. Даже если с азотом бывает потом лопаются либо блок рвут.
@dwalkman210 ай бұрын
Угу, спасибо
@user-dz8vy9hc7p10 ай бұрын
All those tools but yet they don't have any ice to shrink the sleeve so it'll slide nicely in instead of Smashing the top of them to seat it.
@DUKETACTICS3338 ай бұрын
Eso es reponer las camisas de los motores.❤🎉😂 Ánimo
@arcangeloninyanegro2791Ай бұрын
たった少し炙っただけなのにスリープ入れちゃうんだ、プロって本当に神ワザ持ってるんだなあ!
@gongon5059 ай бұрын
freeze sleeve, don't heat block
@averagejoe514310 ай бұрын
Freeze all inserts, heat outsert, 100 degrees spread at least
@charlestheodoreheissman84188 ай бұрын
Кувалда , резак и волшебные слова... Блок после этого должен нагнуться по идее
@user-xi2be6nk8e10 ай бұрын
Гильзы в морозилку а блок греть лучше.
@user-lz9os3nl8b10 ай бұрын
¹
@albertrabe329510 ай бұрын
Ахахахаха, мастера своего дела, сразу видно))) на горячую топ😂
@user-oo1do2mi4y8 ай бұрын
I think cast iron doesn't expand much with heat! the bandstand and cool the shirts! 🤦♂️🤦♂️🤦♂️
@energy1of2the3future10 ай бұрын
Better make absolutely sure those sleeves are perfectly straight
@matthewvasquez1018 ай бұрын
And that's how not to install the liners. Heating the block, hammering are bad bad choices. You should just cover the liners with liquid nitrogen and after it stops "boiling" just slip the liner inside without any need for a hammer or heating. *Heating the engine case like that will deform the metal as well as change it's chemical composition* It will never be the same material as it should be.
@Cr4sHOv3rRiD39 ай бұрын
He montado varias veces cilindros en el bloque y lo adecuado y perfecto es enfriar los cilindros y entrar sin necesidad golpearlos y quedan ajustados al estar temperatura ambiente la cual es casi de inmediato porque el bloque absorve el frío muy rapido
@josesoler24629 ай бұрын
Wrong x The bushing must be cooled for an hour with ice before being put into the cylinder
@AdelAdel-bx4qb8 ай бұрын
Интерестно мастера задумывались о том что когда случается перегрев двигателя то это не есть хорошо.
@Denisius_Vsemogushiy10 ай бұрын
Гильзы не сместятся, на них есть буртик, в блоке проточка.
@user-pg7ml4jh9p9 ай бұрын
If you can freeze the sleeve it would slide right in by hand...
@robrocco54209 ай бұрын
Next time use 2lbs of weed not 1lb
@Jaybird91310 ай бұрын
Каменный век.
@user-mj8vc5qf3x9 ай бұрын
Non à l'ancienne avant c'était comme ça 😊
@ryuz_yt9 ай бұрын
Lo de la temperatura, si bien es cierto, que no podríamos decir que no. A mi me da el vértigo, que precede al ataque de pánico. El objetivo de todo ello es la fiabilidad.
@ignaciogarcia21489 ай бұрын
I always keep a log of wood in my garage tool box
@pavw55089 ай бұрын
Вот что бывает когда школу не закончил, от нагрева метал расширяется, что бы гильзу вставить нужно ее охладить, а не нагревать!
@gxg_tv8 ай бұрын
This is a video of just what not to do when you're installing a sleeve
@user-xo3om9dx6w8 ай бұрын
Liners in to ice then put in block it is easy way
@santhoshtraders503710 ай бұрын
пацаны... вообще ребята....
@romandavydov86843 ай бұрын
Or a sledgehammer and a chunk of wood that's pretty good too LOL
@justcurious77799 ай бұрын
Mejor pongan las camisas en el refrigerador , para que el metal se contraiga 😂
@motivacionyreflexionwfr594610 ай бұрын
What’s the plastic for
@jerrycross31469 ай бұрын
Ah is that for electric cars?
@wizpin10 ай бұрын
Pues es posible, pero hay que tener cuidado. Con una prensa hidráulica se obtienen infinitos mejores resultados. por motivos mas que evidentes.
@ignaciogarcia21489 ай бұрын
Мне блок наверное тоже так делали , микротрещина появилась , два года не мог понять что такое
@Nikolas1981_.8 ай бұрын
All signs of intelligence had left the building a long time ago,
@robpeters52044 ай бұрын
Decía un ingeniero que fue mi maestro... La palabra ingeniería viene de ingenio. A propósito el día 1o de julio fue el día del ingeniero 🎉😊
@rafaeldominguez40649 ай бұрын
Dude just put the sleeves in the freezer for 2-3 hours and they will literally drop in and swell as they warm up .
@arizonawvkid8 ай бұрын
Варвары гильзы нужно охлаждать
@FuckedInTheMouthYoutube9 ай бұрын
Xy-lanh nầy không cần sử dụng ron cao su sao ? Nếu dùng ron cao su làm sao nó chịu nổi nhiệt độ ấy
@thanhuocchau59749 ай бұрын
Hola quería saber x q son así q acaso no son mecánicos como van ASER así para poner en tubo del pistón así es como puede tener a futuro problemas como filtra el aseite
@antoniomora664610 ай бұрын
The har part is getting the old sleeve out right lol
@mrshort49327 ай бұрын
Гильзы нужно было в морозильник на мин 15 положить ! И все чётко зашло бы сама ! Или недостаточно нагрели и в морозильник не положили гильзы !
@grillvalmaty361410 ай бұрын
У меня фотон мотор CY4105 (копия 4bd1) блок грел весь гильзы остужал в холодилтнике сутки не смог поставить... Пришлось потихоньку заприсовывать в блок
@user-ol7oc1cx1r9 ай бұрын
Esa no es la forma correcta
@joseramonbrachodelgado102610 ай бұрын
I feel like oil on a engine and a huge flame isn’t a good idea
@buddybefly33210 ай бұрын
😮 Wouldn't that hurt the heat treatment of the block And make Is the metal harder
@hiimholdin23979 ай бұрын
Era mejor usar el frío ! Que hacer esta barbaridad
@vigilandoalvigilante222310 ай бұрын
Quel motore avrà bisogno di un lungo rodaggio 😂
@user-ys1gn9yz1m3 ай бұрын
Tanpa dipanasi dgn api saja buringnya sdh bisa masuk cuma perlu ditekan dgn kayu dan di pukul pelan2
@teguhdjunaedi308810 ай бұрын
Uff con el hielo seco no hace falta maltratar con tantos golpes 🤦🏼♂️
@aldoflores407810 ай бұрын
Con hielo es Mejor y no golpeas el cilindro
@crbikerrincon24949 ай бұрын
Sleeves can save you money 💰
@reddevil49439 ай бұрын
Chacales congelen las camisas, usen nitrógeno líquido.
@osvaldoayala9559 ай бұрын
Deberían medir la dilatación del cilindro para q la camisa entre suave
@miguelmayorga15339 ай бұрын
Mai visto un sistema simile d’”incamiciare” un cilindro e non mi piace. Solo l’uso dell’azoto liquido è quello consigliato dagli esperti.
@NeroneFromItaly9 ай бұрын
Questi video insegnano che cosa non bisogna mai fare 😂😂😂😂😂
@agolavena10 ай бұрын
Yes. Technology.
@rmleh6 ай бұрын
Че угораете? Нельзя блок нагревать?) Там взрываться бензин будет😂
@StreetCats6669 ай бұрын
😂😂😂 надо мастеру по ремонту по рукам так набить за то что без жидкого азота
@Mr10068510 ай бұрын
Не, всё же хорошо у него есть кувалдочка ,🤣
@user-en2gg9nv1y10 ай бұрын
Eso es un trabajo hecho por principiantes
@DonBotita25 күн бұрын
Como de agencia,dándole con ese garrote
@cesarmendezesquivel85310 ай бұрын
Ben ! c est pas évident ! mais ça le fait !! voilà voilà
@lukaschabotier409710 ай бұрын
You should be freezing the cylinders not heating the block FAIL
@fuzznutz71822 ай бұрын
Ого! ( везде беротт🤫)
@user-bp8ob7rj3x10 ай бұрын
10 тыс хватит поездить , до первой замены масла а там хозяин сам решит ехать опять к этим горе специалистам или нет,это ремонт на скорую руку,не дай бог к таким попасть
@kurmashov143210 ай бұрын
Muy primitivo ese sistema 😊😅😢😂
@CarlosSanchez-kg6ux2 ай бұрын
Что бы так забевать не обязательно греть
@user-gk6qg4bl3v10 ай бұрын
Dry ice or nitro; works better
@angelluna57309 ай бұрын
galing nman po idol
@ragedaspric137310 ай бұрын
Ещё бы гильзу погорели
@bydkabydkin872110 ай бұрын
Thermal cycling freeze sleeves heat block by freezing n heating it changes the growth coefficient of each piece allowing for room should went in lil smoother
@kentaylor862310 ай бұрын
Как же резиновые кольца?
@user-qp8od1oe9f10 ай бұрын
Гильзы ,, сухие".
@user-pg7ml4jh9p9 ай бұрын
Don't you ever disrespect me with your cylinder blowtorch. You hear?
@THEDUDEABlDES9 ай бұрын
Tu amigo el que te cobra más barato jaja.
@leandroluque903810 ай бұрын
Delos que yo tengo un amigo que cobra más barato 😮😮..lo barato sale caro 😅
@pabloyo904110 ай бұрын
Лëд, холодильник, жидкий азот в полевых условиях или на войне. Вы о чëм?
@user-cv5pp4qd2r8 ай бұрын
How to get it out? 🙏
@chiuwaiming8 ай бұрын
in civilized countries the cylinder is placed in liquid nitrogen
@maniboy2k2539 ай бұрын
Se debe enfriar la camisa y entra sola sin un solo golpe. Que mal che
@pablitoaire10 ай бұрын
А пошреть подольше не судьба?))
@dmitrbondar78149 ай бұрын
A ese Mecanico no llego mi carro para eso hay otras formas de introducir las camisas nuevas
Should have put the cylinder sleeves in the freezer as well..
Doubt shop has refrigeration
@@peted5217 when I've done similar interference fits on tooling in the shop just using the lunchroom freezer. It's feasible, freezers are set to -18°C( -0.4°F), cold enough to reduce dimensions a few thousands. Plus heating the block, should drop right in.
Ты думаешь они это не сделали?
They should have had hot ice 🧊 at least mostly most shop for have it, we do.
@@user-sd9jr3po2kThey clearly did not. The exterior color of the sleeves should have frosted when coming near the heated metal. Condensation, it's why you heat or cool, but not both.
Дайте адрес,чтобы туда не ездить.
@@Dark_Stalker404 ахахахах
Только хотел написать😂
🤣🤣🤣🤣
@@Dark_Stalker404в Пакистане без перчаток работают 😂
@@Dark_Stalker404qp
Note to self: Never go there for engine repairs
Put the liners in the deep freeze overnight and they will slide in or very little hammering.
No Don't Hammer Put the cylinder sleeves in to liquid Nitrogen Cold shrinkage then insertion
You're assuming this third world "garage" has money for things that make sense...?
No definitely a rubber mallet and a wood block
Liquid nitrogen? You mean dry ice?
Liquid nitrogen? Good luck finding out if they have 24/7 electricity
Гильзы должны входить от небольшого усилия, ну никак от кувалды, .. Капец двигателю....
Это ,, сухие" гильзы. На дизеле болгарского погрузчика такие гильзы ставили прессом, при этом грели блок двумя паяльными лампами.
@@user-pg7ml4jh9pзначит нужно было охладить гильзы и они бы в блок просто упали.
@@dmitrbondar7814 Гильзы тонкостенные, даже если их где-то как-то охладить, они быстро нагреются. Да и охлаждать их было негде.
I worked in a parts house with a machine shop, they would put the sleeve in dry ice for about half hour ,and use white lead to lubricant and pull it in with a air wrench and a threaded puller, and didn’t heat block,
Well you just added 40k worth of miles to those cylinders and it hasn't even been rebuilt yet.
Не правильно. Нагрев бесполезен, если так заталкивать.
Здесь должен быть жидкий азот.
Да, охладить гильзу
Кого ты лечишь мастер 🧐🧐🧐 они спецы 🤣🤣🤣🤣🤣🤦♂️🤦♂️🤦♂️
Здесь даже пропана будет достаточно.
I used dry ice on the liners and they just fell into the bore
Dry ice work better my friend or a deep freezer do the work
Those idiots are ruining the engine. After the partial heating the block is crooked and will go to waste.
Would of been even better if you removed the locating dowels for the head and cleaned up the block face before fitting the liners because the flame rings on the liners protrute a few thou to seal the gasket and you got next to no show cleaning it properly once liners are in.
Remarkable technique!
Уважаемые че Вам слабо сделать приспособу для постановки ГИЛЬЗ в блок, а это очень просто
Сразу видно мамтны умельцы
Fhffh
Definitely a Honda mechanic
Так ведёт блок бумерангом ! Его надо сразу весь греть ! Или гильзы азотам Эта Не ремонт .простите а филькина грамота !
Все верно дизель М400 гильзы сажают с азотом
도대체 누구한테 배워서 이런 영상을 올리는거야 옛날 옛날 구형차에만 그렇게 작업하거라. 뭐 요즘 신형차들은 엔진 보링할일은 없겠지만....
Как на заводе. Говорят они😂😂😂. Прямо по технологии!
Гильзы полопаются во время работы. Даже если с азотом бывает потом лопаются либо блок рвут.
Угу, спасибо
All those tools but yet they don't have any ice to shrink the sleeve so it'll slide nicely in instead of Smashing the top of them to seat it.
Eso es reponer las camisas de los motores.❤🎉😂 Ánimo
たった少し炙っただけなのにスリープ入れちゃうんだ、プロって本当に神ワザ持ってるんだなあ!
freeze sleeve, don't heat block
Freeze all inserts, heat outsert, 100 degrees spread at least
Кувалда , резак и волшебные слова... Блок после этого должен нагнуться по идее
Гильзы в морозилку а блок греть лучше.
¹
Ахахахаха, мастера своего дела, сразу видно))) на горячую топ😂
I think cast iron doesn't expand much with heat! the bandstand and cool the shirts! 🤦♂️🤦♂️🤦♂️
Better make absolutely sure those sleeves are perfectly straight
And that's how not to install the liners. Heating the block, hammering are bad bad choices. You should just cover the liners with liquid nitrogen and after it stops "boiling" just slip the liner inside without any need for a hammer or heating. *Heating the engine case like that will deform the metal as well as change it's chemical composition* It will never be the same material as it should be.
He montado varias veces cilindros en el bloque y lo adecuado y perfecto es enfriar los cilindros y entrar sin necesidad golpearlos y quedan ajustados al estar temperatura ambiente la cual es casi de inmediato porque el bloque absorve el frío muy rapido
Wrong x The bushing must be cooled for an hour with ice before being put into the cylinder
Интерестно мастера задумывались о том что когда случается перегрев двигателя то это не есть хорошо.
Гильзы не сместятся, на них есть буртик, в блоке проточка.
If you can freeze the sleeve it would slide right in by hand...
Next time use 2lbs of weed not 1lb
Каменный век.
Non à l'ancienne avant c'était comme ça 😊
Lo de la temperatura, si bien es cierto, que no podríamos decir que no. A mi me da el vértigo, que precede al ataque de pánico. El objetivo de todo ello es la fiabilidad.
I always keep a log of wood in my garage tool box
Вот что бывает когда школу не закончил, от нагрева метал расширяется, что бы гильзу вставить нужно ее охладить, а не нагревать!
This is a video of just what not to do when you're installing a sleeve
Liners in to ice then put in block it is easy way
пацаны... вообще ребята....
Or a sledgehammer and a chunk of wood that's pretty good too LOL
Mejor pongan las camisas en el refrigerador , para que el metal se contraiga 😂
What’s the plastic for
Ah is that for electric cars?
Pues es posible, pero hay que tener cuidado. Con una prensa hidráulica se obtienen infinitos mejores resultados. por motivos mas que evidentes.
Мне блок наверное тоже так делали , микротрещина появилась , два года не мог понять что такое
All signs of intelligence had left the building a long time ago,
Decía un ingeniero que fue mi maestro... La palabra ingeniería viene de ingenio. A propósito el día 1o de julio fue el día del ingeniero 🎉😊
Dude just put the sleeves in the freezer for 2-3 hours and they will literally drop in and swell as they warm up .
Варвары гильзы нужно охлаждать
Xy-lanh nầy không cần sử dụng ron cao su sao ? Nếu dùng ron cao su làm sao nó chịu nổi nhiệt độ ấy
Hola quería saber x q son así q acaso no son mecánicos como van ASER así para poner en tubo del pistón así es como puede tener a futuro problemas como filtra el aseite
The har part is getting the old sleeve out right lol
Гильзы нужно было в морозильник на мин 15 положить ! И все чётко зашло бы сама ! Или недостаточно нагрели и в морозильник не положили гильзы !
У меня фотон мотор CY4105 (копия 4bd1) блок грел весь гильзы остужал в холодилтнике сутки не смог поставить... Пришлось потихоньку заприсовывать в блок
Esa no es la forma correcta
I feel like oil on a engine and a huge flame isn’t a good idea
😮 Wouldn't that hurt the heat treatment of the block And make Is the metal harder
Era mejor usar el frío ! Que hacer esta barbaridad
Quel motore avrà bisogno di un lungo rodaggio 😂
Tanpa dipanasi dgn api saja buringnya sdh bisa masuk cuma perlu ditekan dgn kayu dan di pukul pelan2
Uff con el hielo seco no hace falta maltratar con tantos golpes 🤦🏼♂️
Con hielo es Mejor y no golpeas el cilindro
Sleeves can save you money 💰
Chacales congelen las camisas, usen nitrógeno líquido.
Deberían medir la dilatación del cilindro para q la camisa entre suave
Mai visto un sistema simile d’”incamiciare” un cilindro e non mi piace. Solo l’uso dell’azoto liquido è quello consigliato dagli esperti.
Questi video insegnano che cosa non bisogna mai fare 😂😂😂😂😂
Yes. Technology.
Че угораете? Нельзя блок нагревать?) Там взрываться бензин будет😂
😂😂😂 надо мастеру по ремонту по рукам так набить за то что без жидкого азота
Не, всё же хорошо у него есть кувалдочка ,🤣
Eso es un trabajo hecho por principiantes
Como de agencia,dándole con ese garrote
Ben ! c est pas évident ! mais ça le fait !! voilà voilà
You should be freezing the cylinders not heating the block FAIL
Ого! ( везде беротт🤫)
10 тыс хватит поездить , до первой замены масла а там хозяин сам решит ехать опять к этим горе специалистам или нет,это ремонт на скорую руку,не дай бог к таким попасть
Muy primitivo ese sistema 😊😅😢😂
Что бы так забевать не обязательно греть
Dry ice or nitro; works better
galing nman po idol
Ещё бы гильзу погорели
Thermal cycling freeze sleeves heat block by freezing n heating it changes the growth coefficient of each piece allowing for room should went in lil smoother
Как же резиновые кольца?
Гильзы ,, сухие".
Don't you ever disrespect me with your cylinder blowtorch. You hear?
Tu amigo el que te cobra más barato jaja.
Delos que yo tengo un amigo que cobra más barato 😮😮..lo barato sale caro 😅
Лëд, холодильник, жидкий азот в полевых условиях или на войне. Вы о чëм?
How to get it out? 🙏
in civilized countries the cylinder is placed in liquid nitrogen
Se debe enfriar la camisa y entra sola sin un solo golpe. Que mal che
А пошреть подольше не судьба?))
A ese Mecanico no llego mi carro para eso hay otras formas de introducir las camisas nuevas
CO2 fire extinguisher will do the job
ни делайте так никогда